2014 Alfa Romeo 4C reset

❒press the
or
button to make the
adjustment;
❒ briefly press the SET/
button to
go back to the menu screen or hold
the button down to go back to the
standard screen without saving.
Belt reminder (Buzzer
reactivation for SBR
indication)
(for versions/markets, where provided)
This function can be displayed only
after a dedicated Alfa Romeo
Dealership has deactivated the SBR
system (see "SBR system" paragraph in
the "Safety" chapter).
Service (Scheduled
servicing)
With this function it is possible to view
information on mileage or time intervals
for servicing.
To consult this information, proceed as
follows:
❒ press button SET/
briefly. The
display shows the service interval
in kilometres (km) or miles (mi)
according to the previous setting (see
the "Unit of measurement (Setting
the unit of measurement)"
paragraph); ❒
briefly press the SET/
button to
go back to the menu screen or hold
the button down to go back to the
standard screen.
IMPORTANT The “Scheduled Servicing
Plan” includes car maintenance at
fixed intervals, refer to the
"Maintenance and care" chapter. The
"Service" function is automatically
displayed, along with thewarning
light coming on, with key at MAR-ON -
starting from 2,000 km (or equivalent
value in miles) before these deadlines
and is activated again every 200 km (or
equivalent value in miles). Below 200
km servicing indications are more
frequent. The indication will appear in
kilometres or miles according to the
"Unit of measurement" settings. In
addition, when the vehicle mileage is
close to a scheduled servicing ("service
coupon"), and the key is turned to
MAR-ON, the
warning light will
appear on the display along with the
word "Service" and followed by the
number of kilometres or miles left
before vehicle servicing. Contact a
dedicated Alfa Romeo Dealership. The
operations in the “Scheduled Servicing
Plan” will be performed and the
message will be reset. Passenger airbags
(Activation/Deactivation
of passenger's side
front airbag)
This function is used to activate/
deactivate the front passenger's airbag.
Proceed as follows:
❒
press the SET/
button and, after
the message (Bag pass: Off) (to
deactivate) or (Bag pass: On) (to
activate) is displayed by pressing
buttons "
"or"
", press the SET/
button again;
❒ a confirmation request message will
appear on the display;
❒ by pressing the
or
buttons
select "Yes" (to confirm activation/
deactivation) or "No" (to cancel);
❒ press the SET/
button briefly, a
message confirming the selection
will be displayed and you will go back
to the menu screen, or hold the
button down to go back to the
standard screen without saving. The
warning light
in the instrument
panel switches on.
67
24-9-2013 11:49 Pagina 67

Daytime running lights
(DRL)
(for versions/markets, where provided)
With this function is possible to turn the
daytime running lights on and off.
Proceed as follows to activate or
deactivate this function:
❒press button SET/
briefly. "On"
or "Off" flash on the display,
according to what has been
previously set;
❒ press
or
to make your choice;
❒ press the SET/
button briefly
to go back to the submenu screen or
hold the button down to go back to
the main menu screen without
saving;
❒ hold down the SET/
button
again to go back to the standard
screen or to the main menu
according to the menu options where
you are in. Exit Menu
This is the last function that closes the
cycle of settings listed in the menu
screen.
Briefly press the SET/
button to go
back to the standard screen without
saving.
Press the
button to return to the first
menu option.
TRIP COMPUTER
IN BRIEF
The Trip computer is used to display
information on car operation when
the key is turned to MAR-ON.
This function is characterised by two
separate records, called "Trip A"
and "Trip B", where the car's
"complete missions" (journeys) are
recorded in a reciprocally
independent manner.
Both records can be reset: i.e. start
of a new journey.
“Trip A” is used to display the values
relating to:
❒ Range
❒ Distance travelled
❒ Average consumption
❒ Instant consumption
❒ Average speed
❒ Trip time (driving time).
“Trip B” is used to display the values
relating to:
❒ Distance travelled B
❒ Average consumption B
68
KNOWING THE INSTRUMENT PANEL
24-9-2013 11:49 Pagina 68

❒Average speed B
❒ Trip time B (driving time).
“Trip B” may be disabled (see "Trip B
Activation/Data (Trip B enablement)"
paragraph). The “Range” and “Instant
consumption" values cannot be reset.
VALUES DISPLAYED
Range
This indicates the approximate distance
that can still be travelled with the fuel
in the tank, assuming that driving style
remains unvaried.
The display will show the reading “- - -
-” when the following events take place:
❒ range value lower than 50 km (or 30
mi)
❒ car parked with engine running for a
long period.
IMPORTANT The range value variation
can be affected by several factors:
driving style, type of route (motorway,
urban, mountain roads, etc.), conditions
of use (load, tyre pressures, etc.). Trip
planning must therefore take the above
into account. Distance travelled
This value shows the distance covered
from the start of the new journey.
Average consumption
This value shows the approximate
average fuel consumption from the start
of the new journey.
Instant consumption
This value shows the instant fuel
consumption. The value is constantly
updated. The display will show “----”
if the car is parked with the engine
running.
Average speed
This value shows the car's average
speed based on the overall time
elapsed since the start of the new
journey.
Trip time
Time elapsed since the start of the new
journey.
Indications on display
Each time a value is selected, the
following information is shown:
❒
the word “Trip” (or “Trip A” or “Trip B”)
(A fig. 62);
❒ name, value and unit of measure of
the selected value (e.g. "Range 520
km") (B fig. 62).
After a few seconds, the name of the
selected value is replaced by the
corresponding icon (see example fig.
63).
TRIP RESET button
The TRIP RESET button is located on
the right stalk fig. 64. With the ignition
key at MAR-ON, it allows you to view
the values described previously and
also reset them to begin a new journey:
❒ brief press: display various values;
62
A0L0122
69
24-9-2013 11:49 Pagina 69

❒long press: reset values and start a
new journey.
New journey
This begins after a reset:
❒ “manual” resetting by the user, by
pressing the relevant button; ❒
“automatic” resetting, when the “trip
distance” reaches 99999.9 km or
when the “trip time” reaches 999:59
(999 hours and 59 minutes);
❒ after disconnection/reconnection of
the battery. IMPORTANT The reset operation, when
"Trip A" or "Trip B" details are being
displayed, only resets the values
associated with the journey displayed.
Start of journey
procedure
With the ignition key at MAR-ON, reset
by holding the TRIP RESET button
down for more than 2 seconds.
Trip exit
The Trip function ends automatically
once all the values have been
displayed. You can exit manually by
holding the SET/
button down for
more than 1 second.
63
A0L0123
64
A0L0124
70
KNOWING THE INSTRUMENT PANEL
24-9-2013 11:49 Pagina 70

Warning lights ondisplay What it means
What to do
amberEXTERIOR LIGHTS FAULT
The symbol and corresponding message appear
on the display if a fault is detected in one of the
following lights:
❒
daytime running lights (DRL)
❒ side lights
❒ dipped headlights
❒ direction indicators
❒ rear fog lights
❒ reversing lights
❒ number plate lights.
The fault relating to these lights may be caused
by: one or more blown fuses, one or more blown
bulbs or a broken electrical connection. Check, and if necessary replace the fuses
involved, in accordance with the "Fuse
replacement" paragraph in the "In an emergency"
chapter; if this does not resolve the fault, check,
and if necessary replace, the bulbs involved, in
accordance with the "External bulb replacement"
paragraph in the "In an emergency" chapter.
Should this operation also fail to resolve the fault,
contact the dedicated Alfa Romeo Dealership, for
a comprehensive check of the electrical system.amber
SERVICE (SCHEDULED SERVICING)
The
digital warning light is automatically
displayed, along with a dedicated message, with
key at MAR-ON, 2,000 km (or equivalent value in
miles) before the following scheduled servicing
interval and is activated again every 200 km (or
equivalent value in miles). Contact a dedicated Alfa Romeo Dealership. The
operations in the “Scheduled Servicing Plan” will
be performed and the message will be reset.
84
KNOWING THE INSTRUMENT PANEL
24-9-2013 11:49 Pagina 84