2014 Acura TL stop start

Î
ÎÎIf you see a ‘‘CHECK DRL
SYSTEM’’ message on the multi-
inf ormation display, there is a
problem with the daytime running
light system. Take your vehicle to a
dealer to have it checked.
The headlights revert to normal
operation when you turn them on
with the switch.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. VEHICLE
OFF (LOCK) Mode is the
equivalent of LOCK (0). For
more inf ormation, see pages
and . With the headlight switch of f or in
the position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pagesand .
The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights on
reminder beeper.
:
:
184 187
184 187
Headlights
Daytime Running L ights
142
12/07/20 10:47:29 31TK4640_147

´
µ
´ µ Î
Î
Turn the f og lights on and of f by
turning the switch next to the
headlight switch.
You can use the f og lights only when
the headlights are on low beam.
With the light switch in the AUTO
position, you can also use the f og
lights when the headlights turn on
automatically. They will go of f when
the headlights turn of f .
Adjust the brightness of the
instrument panel by pressing the
or button with the ignition
switch in the ON (II) position. Press
the button to increase the
brightness and the button to
decrease it. Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
:
184 187
CONT INUED
Fog L ights Instrument Panel Brightness
Fog L ights, Instrument Panel Brightness
Inst rument s and Cont rols
143
FOG LIGHT SWITCH
ADJUSTMENT BUTTONS
12/07/20 10:47:37 31TK4640_148

Push the lever up to lock the
steering wheel in that position.
Make any steering wheel
adjustments before you start driving.
Push the lever under the steering
column all the way down.
Move the steering wheel up or
down, and in or out, so it points
toward your chest, not toward
your f ace. Make sure you can see
the instrument panel gauges and
indicators.Make sure you have securely
locked the steering wheel in place
by trying to move it up, down, in,
and out.
1.
2. 3.
4.
Steering Wheel A djustments
146
LEVER
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.
12/07/20 10:47:56 31TK4640_151

Î
Î Î
Î
CONT INUED
Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Use
only Acura-approved key blanks.The immobilizer system protects
your vehicle f rom thef t. If an
improperly coded key or keyless
access remote (or other device) is
used, the engine’s f uel system is
disabled.
When you turn the ignition switch to
the ON (II) position, or select the
ON mode with the engine start/
stop button, the immobilizer system
indicator should come on brief ly,
then go off. If the indicator starts to
blink, it means the system does not
recognizethecodingof thekeyor
keyless access remote.
On models without keyless access
system, turn the ignition switch to
the LOCK (0) position, remove the
key, reinsert it, and turn the ignition
switch to the ON (II) position again.On models with keyless access
system, set the power mode to
VEHICLE OFF (LOCK), then select
theONmodeagain.
The system may not recognize your
key’s or remote’s coding if another
immobilizer key or other metal
object (i.e. key chain) is near the
ignition switch or the keyless access
remote when you insert the key or
set the power mode to ON.
Your vehicle has the engine
start/stop button instead of an
ignition switch. See page f or
a comparison between
conventional power switches
and your engine start/stop
button. For more inf ormation on
selecting the power mode, see
page .
: On models with keyless access
system
184 187
Keys and Locks, Immobilizer System
Immobilizer System
Inst rument s and Cont rols
149
12/07/20 10:48:19 31TK4640_154

Î
Î
You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or the
ACCESSORY (I) position and open
thedriver’sdoor.Removethekeyto
turn of f the beeper.
You will also see a ‘‘REMOVE KEY’’
message on the multi-inf ormation
display.
TheshiftlevermustbeinPark
bef ore you can remove the key f rom
the ignition switch.
Go to page f or inf ormation on
the engine start/stop button.
To lock all doors, push the f ront of
the master door lock switch on
either f ront door, pull the lock tab
rearward on the driver’s door, or
turn the key counterclockwise in
the outside lock on the driver’s door.
Thebuilt-inkeycanbeusedtolock/
unlock the doors when the remotebattery becomes weak and the
power door lock/unlock operation is
disabled. For more inf ormation, see
page .
Pushing the rear of either master
door lock switch will unlock all doors.
Pushing f orward the lock tab on the
driver’s door unlocks only that door.
The lock tab on any passenger’s door
locks and unlocks that door.
184 201
CONT INUED
On models with keyless access system
On models with keyless accesssystem
Ignit ion Swit ch, Door L ocks
Door L ocks
Inst rument s and Cont rols
151
MASTER DOOR LOCK SWITCH
Lock
Unlock
Lock
Unlock RED INDICATOR
LOCK TAB
13/08/08 16:43:18 31TK4650_156

µ
Î
Î
CONT INUED
See pages f or important saf etyinf ormation and warnings about how toproperly position the seats and seat-backs.
Driver’s seat only:
1513
The passenger seat has the same
adjustments as the driver’s seat but
without any lumbar adjustment. Raises or lowers the seat.
Moves the whole seat up
and f orward, or down
and backward. The front
of the seat also tilts up or
down at the same time.
Adjusts the seat-back
angle f orward or
backward.
The controls f or the power
adjustable front seats are on the
outside edge of each seat bottom.
You can adjust the seats with the
ignition switch in any position.
Make all seat adjustments bef ore
you start driving.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. VEHICLE
OFF (LOCK) Mode is the
equivalent of LOCK (0),
ACCESSORY Mode is the
equivalent of ACCESSORY (I), and ON Mode is the equivalent
of ON (II). For more
information, see pages and
.
Moves the seat forward
and backward.
Moves the f ront of the
seat up or down. Increases or decreases
the lumbar support.
: 187
184
Seats
Front Seat Power A djustments
Inst rument s and Cont rols
161
Driver’s seat
12/07/20 10:50:05 31TK4640_166

Î
ÎBoth outside door mirrors have a
reverse tilt f eature. When in
reverse, the selected mirror will
tilt down slightly to improve your
view as you parallel park. Shifting
out of reverse will return the
mirror to its original position.
To tilt the driver’s mirror, place
the selector switch in the left
position.
To tilt the passenger’s mirror,
place the switch in the right
position.
To turn the feature off, place the
switch in the center position.
When you f inish, move the
selector switch to the center (off)
position. This turns the
adjustment switch of f to keep your
settings.
Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown. With the ignition switch in the
ON (II) position, move the
selector switch to the L (driver’s
side), or R (passenger’s side). Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
Outside mirror positions can be
stored in the driving position
memory system (see page ). 3.
1.
2. :
184 187 170
Adjusting the Power Mirrors Reverse Tilt Door Mirror
Mirrors
168
ADJUSTMENT SWITCH
SELECTOR SWITCH
12/07/20 10:50:56 31TK4640_173

ÎÎ
Î This heated mirror f unction has a
timer (see page ).
The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, or the power mode ON,
turn on the heaters by pressing the
button. The indicator in the button
comesonasareminder.Pressthe
button again to turn the heaters off.
Pressing this button also turns the
rear window def ogger on and of f . Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
If the outside temperature is below
41°F (5°C), the heated mirror
function will come on automatically
f or 10 minutes when you turn the
ignition switch to the ON (II)
position. :
145
184 187
Mirrors
Power Mirror Heaters
Inst rument s and Cont rols
169
HEATED MIRROR BUTTON
12/07/20 10:51:02 31TK4640_174