2014 Acura TL key

µ
Remove the old battery and note
the polarity. Make sure the
polarity of the new battery is the
same ( side f acing up), then
insert it in the keypad.
Place a cloth on the edge of the
keypad to prevent scratches, and
remove the upper half by carefully
prying on the edge with a small
f lat-tip screwdriver or coin. An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations f or
battery disposal.
Snap the two halves of the keypad,
then install the parts in reverse
order. This device complies with the
appropriate requirements or the
required standards. See page f or
more inf ormation.
4.
5.
3. 628
Remote Transmitter
Inst rument s and Cont rols
159
BATTERY
12/07/20 10:49:43 31TK4640_164

µ
Î
Î
CONT INUED
See pages f or important saf etyinf ormation and warnings about how toproperly position the seats and seat-backs.
Driver’s seat only:
1513
The passenger seat has the same
adjustments as the driver’s seat but
without any lumbar adjustment. Raises or lowers the seat.
Moves the whole seat up
and f orward, or down
and backward. The front
of the seat also tilts up or
down at the same time.
Adjusts the seat-back
angle f orward or
backward.
The controls f or the power
adjustable front seats are on the
outside edge of each seat bottom.
You can adjust the seats with the
ignition switch in any position.
Make all seat adjustments bef ore
you start driving.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. VEHICLE
OFF (LOCK) Mode is the
equivalent of LOCK (0),
ACCESSORY Mode is the
equivalent of ACCESSORY (I), and ON Mode is the equivalent
of ON (II). For more
information, see pages and
.
Moves the seat forward
and backward.
Moves the f ront of the
seat up or down. Increases or decreases
the lumbar support.
: 187
184
Seats
Front Seat Power A djustments
Inst rument s and Cont rols
161
Driver’s seat
12/07/20 10:50:05 31TK4640_166

Make sure all items in the trunk and
those extending through the pass-
through are secured.Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
For security, this cover can be
locked and unlocked only with the
master key(the built-in key on
models with keyless access system).
To lock the cover, insert the key, and
turn it clockwise.
Never drive with this cover open and
the trunk lid open.
See on
page . When driving af ter dark, the
automatic dimming rearview mirror
reduces the glare f rom headlights
behind you.
57
CONT INUED
Mirrors
Carbon Monoxide Hazard
Seats, Mirrors
Inst rument s and Cont rols
167
SENSOR
INDICATOR
There is also a sensor on the back of
the mirror. Items hung on the mirror
may block this sensor and af f ect its
perf ormance.
13/04/02 19:11:30 31TK4640_172

Î
ÎBoth outside door mirrors have a
reverse tilt f eature. When in
reverse, the selected mirror will
tilt down slightly to improve your
view as you parallel park. Shifting
out of reverse will return the
mirror to its original position.
To tilt the driver’s mirror, place
the selector switch in the left
position.
To tilt the passenger’s mirror,
place the switch in the right
position.
To turn the feature off, place the
switch in the center position.
When you f inish, move the
selector switch to the center (off)
position. This turns the
adjustment switch of f to keep your
settings.
Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown. With the ignition switch in the
ON (II) position, move the
selector switch to the L (driver’s
side), or R (passenger’s side). Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
Outside mirror positions can be
stored in the driving position
memory system (see page ). 3.
1.
2. :
184 187 170
Adjusting the Power Mirrors Reverse Tilt Door Mirror
Mirrors
168
ADJUSTMENT SWITCH
SELECTOR SWITCH
12/07/20 10:50:56 31TK4640_173

ÎÎ
Î This heated mirror f unction has a
timer (see page ).
The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, or the power mode ON,
turn on the heaters by pressing the
button. The indicator in the button
comesonasareminder.Pressthe
button again to turn the heaters off.
Pressing this button also turns the
rear window def ogger on and of f . Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
If the outside temperature is below
41°F (5°C), the heated mirror
function will come on automatically
f or 10 minutes when you turn the
ignition switch to the ON (II)
position. :
145
184 187
Mirrors
Power Mirror Heaters
Inst rument s and Cont rols
169
HEATED MIRROR BUTTON
12/07/20 10:51:02 31TK4640_174

Î
Î Store a driving position only when
the vehicle is parked.
Your vehicle has a memory feature
f or the driver’s seat and outside
mirror positions.
Seat, except f or power lumbar, and
outside mirror positions can be
stored in separate memories. You
select a memorized position by
pushing the appropriate button or
using the appropriate remote
transmitter or the keyless access
remote (Driver 1 or Driver 2).
Adjust the seat to a comfortable
position (see page ).
Adjust the outside mirrors f or best
visibility (see page ).Press and release the SET button
on the control panel. You will hear
a beep. Immediately press and
hold one of the memory buttons (1
or 2) until you hear two beeps.
The indicator in the memory
button will come on. The current
positions of the driver’s seat and
outside mirrors are now stored.
Turn the ignition switch to the
ON (II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages and . 3.
1.
2. :
184 168
187
161
Storing a Driving Position in
Memory
Driving Position Memory System
170
MEMORY BUTTONS
SET BUTTON
12/07/20 10:51:10 31TK4640_175

Fail to press a memory button
within 5 seconds.
To cancel the storing procedure
af ter pressing the SET button, do
any of the f ollowing:
To select a memorized position, do
this:
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button.
Make sure the parking brake is set
and the shif t lever is in Park
(automatic).
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
Change the power mode out f rom
ON. Turn the ignition switch out from
the ON (II) position. Readjust the outside mirror
position. Readjust the seat position.
Press the SET button again within
5 seconds.
1.
2.
CONT INUED
On models with keyless access system
On models without keyless access
system
Driving Position Memory System
Selecting a Memorized Position
Inst rument s and Cont rols
171
MEMORY BUTTONS
12/07/20 10:51:20 31TK4640_176

Always keep the remote and the
built-in key away from any magnetic
material.
Youshouldhavereceivedakey
number tag with your built-in key.
You will need this key number if you
ever have to get a lost key replaced.
UseonlyAcura-approvedkeyblanks.
Your vehicle has a keyless access
system. This system allows you to
operate the vehicle without an
ignition key. When you carry the
remote with you, you can lock/
unlock the door(s), unlock the trunk,
and start the engine.
When the vehicle battery is dead. When the remote battery is dead. A vehicle is being operated with a
transmitter nearby. The remote is covered by metal. You carry a cell phone, a laptop
computer, or other electrical
device near the remote. There is strong electrical current
nearby. Thebatteryof theremoteisweak.
The system may not work if: Each keyless access remote has a
built-in key. This key is used to lock/
unlock the doors when the remote
battery becomes weak and the
power door lock/unlock operation is
disabled. You cannot start the engine
with this key.
Make sure the driver always carries
the remote/built-in key set.
Protect the remote and the built-in
key f rom direct sunlight, high
temperature, and high humidity.
Do not drop the remote or the
built-in key, and do not set heavy
objects on them.
Keep the remote and the built-in key
away f rom liquids. If they get wet,
dry them immediately with a sof t
cloth.
The built-in keys do not contain
batteries.On models with navigation system
K eyless A ccess System
Inst rument s and Cont rols
173
12/07/20 10:51:40 31TK4640_178