50
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
HEADLIGHTS
BEAM DIRECTION
The correct orientation of the headlights
is important for drivers comfort and safe-
ty. Besides, it is a specific rule of the high-
way code.
The headlights must be correctly directed
to ensure the best visibility conditions for
all drivers.
Contact Abarth Dealership to have the
headlights properly adjusted.
Check beam aiming every time the load or
its distribution changes.
IMPORTANT When turning on (Xenon)
gas discharge headlight lamps (for ver-
sions/markets, where provided), it is nor-
mal that there should be a vertical move-
ment of reflectors, and consequently the
same will also happen to the light beam,
for the time required to achieve the cor-
rect headlight trim stabilisation, equal to
approx. 2 seconds.
ROOF RACK/SKI RACK
FASTENERS
The fasteners are located in the area in-
dicated in fig. 55.
To use the front fasteners, remove the cap
A, accessible with the door open. To lo-
cate rear fasteners B, refer to fig. 56.
Lineaccessori provides a specific rack/ski
rack on tailgate.
IMPORTANT Follow the instructions
contained in the assembly kit to the letter.
Assembly must be performed by qualified
personnel.
fig. 55F0S055Ab
After travelling for a few
kilometres, check again that
fastening screws are properly tight-
ened.
WARNING
Never exceed the maximum
allowed load (see “Technical
Specifications”).
Evenly distribute the load and
take into account, when dri-
ving, the increased respon-
siveness of the car to side
wind.
Comply with applicable laws
concerning maximum over-
all dimensions.
WARNING
fig. 56
30 mm
130 mm
F0S056Ab
046-062 ABARTH 500 1ed GB:046-064 ABARTH 500 GB 24-05-2012 9:50 Pagina 50
51
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
BEAM ADJUSTMENT fig. 57
The car is provided with electric adjust-
ment of the beams, operating with ignition
key on MARand low beams on.
The car will slant backwards when it is
loaded, raising the light beam.
In that case, it is necessary to perform
beams adjustment with buttons +and –.
The display provides a visual indication of
the positions during adjustment.
Gas discharge headlights (Xenon head-
lights) are automatically adjusted. The
headlight position is electronic and there-
fore cannot be manually adjusted using the
+and –buttons.
fig. 57
M E N UE S C
F0S057Ab
Correct positions depending
on load
Position 0- one or two passengers on
front seats.
Position 1- 4 passengers.
Position 2- 4 passengers + load in the
boot.
Position 3- driver + maximum admitted
load in the boot.
AIMING THE FRONT
FOG LIGHTS
(for versions/markets, where provided)
Contact Abarth Dealership to have the
headlights properly adjusted.
BEAMS ADJUSTMENT ABROAD
Low beams factory adjustment depends
on the country where the car is pur-
chased. When you travel in countries with
different driving direction, to avoid blind-
ing the drivers who travel in the opposite
direction, it is necessary to cover the ar-
eas of the beam according to the provi-
sions of the Highway Code of the country
where you travel.ABS SYSTEM
(for versions/markets, where provided)
The car is fitted with an ABS braking sys-
tem, which prevents the wheels from lock-
ing when braking, makes the most of road
grip and gives the best control when emer-
gency braking under difficulty road condi-
tions.
The system is completed by EBD (Elec-
tronic Braking Force Distribution), which
distributes the braking action between
front and rear wheels.
IMPORTANT To achieve maximum effi-
ciency of the braking system, a settlement
period of about 500 km is required: dur-
ing this time, avoid sudden, repeated and
prolonged braking.
046-062 ABARTH 500 1ed GB:046-064 ABARTH 500 GB 24-05-2012 9:50 Pagina 51
