2014.5 VAUXHALL CORSA light

156Vehicle care
2. Remove bulb from socket, insertnew bulb.
3. Insert bulb holder in reflector so that the locating tab of the bulb
holder aligns with the reflector
recess.
4. Rotate clockwise to engage.
Front turn signal light
Front turn signal lights are equipped
with longlife bulbs. In case of failure,
have bulb replaced by a workshop.
Adaptive forward lighting
Headlights have separate systems for low and high beam 1 (outer bulb),
cornering light 2 (inner bulb) and
daytime running light/side light 3.
Low/high beam
1. Disengage wire clip and remove
protective cover 1.

Vehicle care157
2. Rotate bulb holder anticlockwiseto disengage.
Withdraw bulb holder from
reflector.
3. Insert new bulb in reflector so that
the locating tab of the bulb holder
aligns with the reflector recess.
4. Engage bulb holder by turning clockwise.
5. Put on protective cover and engage wire clip.
Daytime running light/Side light
1. Rotate bulb holder 3
anticlockwise to disengage.
Withdraw bulb holder from
reflector.
2. Remove bulb from socket, insert new bulb.
3. Insert bulb holder in reflector so that the locating tab of the bulb
holder aligns with the reflector
recess.
4. Rotate clockwise to engage.

158Vehicle care
Cornering light
1. Rotate protective cover 2
anticlockwise and remove.
2. Detach wiring plug from bulb.
3. Disengage spring clip from retainer by moving and swivelling
to the side.
4. Remove bulb from reflector housing.
5. When installing the new bulb, insert lugs in the reflectorrecesses.
6. Install spring clip, plug connector onto bulb.
7. Install protective cover.
Front turn signal light
1. Disengage wire clip and remove protective cover 1.

Vehicle care159
2. Rotate bulb holder anticlockwiseto disengage.
Withdraw bulb holder from
reflector.
3. Push bulb into socket slightly, rotate anti-clockwise and remove.
4. Insert new bulb by slightly pressing and rotating.
5. Insert bulb holder in reflector and engage by turning clockwise.
6. Put on protective cover and engage wire clip.
Fog lights
The bulbs are accessible from the
underside of the vehicle.
1. Turn the bulb holder anticlockwise
and remove it from the reflector.
2. Disengage the bulb holder from the plug connector by pressing
the retaining lug.
3. Remove and replace the bulb holder with bulb.
4. Attach the plug connector.
5. Insert the bulb holder into the reflector.
6. Turn the bulb holder clockwise and engage.

160Vehicle careTail lights5-door passenger vehicle
1. Open side cover. When replacing bulbs on the righthand side, first remove the tools
and the jack or the tyre repair kit,
then remove the tool box.
2. Remove plug connector by pressing on bulb holder tab.
3. Hold bulb housing from the outside; unscrew two retaining
nuts.4. Detach bulb housing towards the rear.

Vehicle care161
5. Gently press the three lockinglugs on the outside of the bulb
holder outwards and remove bulb
holder.
6. Push bulb into socket slightly, rotate anti-clockwise, remove and
renew bulb.
Rear fog light, may be only on one side ( 1)
Reverse light ( 2)
Turn signal light ( 3)
Tail light/side light ( 4)
Tail light/brake light ( 5)
7. Engage bulb holder in bulb
housing, ensuring that it properly
engages.
8. Ensure that the bulb holder seal is
positioned as illustrated.
9. Insert bulb housing in vehicle body, tighten securing nuts by
hand. Engage plug connector.
Close cover.
After bulb replacement, check the tail lights for proper functionality: switch
on the ignition, operate the brake,
switch on the sidelights.

162Vehicle care
3-door passenger vehicle, van
1. Open side cover.When replacing bulbs on the righthand side, first remove the tools
and the jack or the tyre repair kit,
then remove the tool box.
2. Remove plug connector by pressing on bulb holder tab.
3. Hold bulb housing from the outside; unscrew two retaining
nuts.4. Remove tail light assembly.

Vehicle care163
5. Gently press the three lockinglugs on the outside of the bulb
holder outwards and remove bulb
holder.
6. Push bulb into socket slightly, rotate anti-clockwise, remove and
renew bulb.
Reverse light (right side), rear fog
light (left side) ( 1)
Tail light ( 2)
Turn signal light ( 3)
Tail light/brake light ( 4)
Tail light ( 5)
7. Engage bulb holder in bulb
housing, ensuring that it properly
engages.
8. Ensure that the bulb holder seal is
positioned as illustrated. Fit the
round seal on the fastening bolt.
9. Insert bulb housing in vehicle body, and tighten securing nuts byhand. Engage plug connector.
Close and lock cover.
After bulb replacement, check the tail
lights for proper functionality: switch
on the ignition, operate the brake,
switch on the sidelights.
Side turn signal lights
To replace bulb, remove lamp
housing:
1. On left vehicle side, slide lamp to the front and remove it out of the
front wing with the rear end.
On right vehicle side, slide lamp to
the rear and remove it out of the front wing with the front end.