2014.5 Peugeot Bipper clock

85
Bipper_en_Chap05_technologie_ed02-2014
Menu...Press...Sub-
menu...Press... Select... Confirm
and exitEnables you to...
1 Speed beep ON
Increase
Activate/Deactivate the audible
signal indicating exceeding of the
programmed speed.
Modify the speed setting.
Decrease
OFF
2


Activate
trip
B ON
Activate
Display a second trip,
"
t
rip B".
OFF Deactivate
3


Set
time Hours
Increase
Adjust the clock
Decrease
Format 24 h
Select the display mode for the
clock.
12 h
4 Set date Year /
Month / DayIncrease
Adjust the date.
Decrease
This button enables
you to:
-

access the menus and

sub-menus, This button enables you to:
-
scroll up through a menu,
-

increase a value.
This button enables you to: -

scroll down through a menu,
-

decrease a value.
-


confirm your selections within a menu,
-


exit from the menus.
A
long press enables you to return to the
home screen.
5
TECHNOLOGY on BOARD
Vehicle configuration

156
Bipper_en_Chap09_aide-rapide_ed02-2014
Removing a wheel
1. Park the vehicle on level, stable and non-
slippery ground. Apply the parking brake.
Switch off the ignition and engage first
gear or reverse, depending on the slope.
2.

Detach
the wheel trim (large model) using
the wheelbrace 1 , pulling at the valve
passage hole.
Slide the screwdriver

3 into the notch on
the trim (small model) and use the tool as
a lever, pressing to unclip the trim.
3.

Slacken the wheel bolts using the

wheelbrace. 4.
Position the jack underneath the body ,
in accordance with the illustration, at the
mark A (on the sill) as close as possible
to the wheel to be changed.
5.
e xtend the jack 4 until its base is in
contact with the ground.
e nsure that the
centreline of the jack base is vertical in
relation to the location used.
6.

Raise the vehicle.
7.


Remove the bolts and detach the wheel.
Putting the wheel back in place
1. Install the support on the wheel.
2.
Place the cable
B in position.
3.
l ower the cover A .
4.

Position the wheel.
5.

t
urn the wheelbrace clockwise to fully

raise the spare wheel.
Changing a wheel

159
Bipper_en_Chap09_aide-rapide_ed02-2014
- If a pressure of at least 1.5 bars is not
reached within 5 minutes:
●

disconnect the compressor from the
valve and from the 12 V accessory
socket,
●


move the vehicl
e forward by
approximately 10 metres to distribute the
filling fluid inside the tyre,
●

then repeat the inflation operation
.
-

If a pressure of at least
1.8 bars is not
reached within 10 minutes:
●

stop the repair p
rocedure; the tyre has
suffered too much damage and cannot
be repaired,
●

contact a PEUGEOT
dealer or a qualified
workshop.
-

If the tyre has been inflated to a pressure

of 3 bars, set off again immediately.
After driving for approximately 10 minutes,
stop and check the pressure of the tyre
again.
Adjust the tyre pressure if necessary and
contact a P
euge O t
dealer or a qualified

workshop as soon as possible.
You must inform the technician that you
have repaired the tyre using the temporary
puncture repair kit and show him its
instructions.
Checking and correcting the pressure
For checking and correcting the pressure of
a tyre, use the compressor as follows:
-

disconnect the pipe
I,
-

connect it directly to the tyre valve,
t

he cartridge will then be connected to
the compressor and the sealant will not be
injected.
Replacing the repair cartridge
Disconnect the pipe I .
turn the empty cartridge anticlockwise and


lift it.
Insert the new cartridge and turn it
clockwise.
Reconnect the pipe I and connect the pipe B
to its location.
t

he repair cartridge contains ethylene-
glycol, a product which is harmful if
swallowed and which causes irritation to the
eyes.
Keep this product out of reach of children.
After use, take the cartridge to a P
euge O t

dealer or to an authorised waste disposal


site.
If the tyre has to be deflated:
-

connect the pipe

I to the tyre valve,
-

press the yellow button, located in the


centre of the switch F on the compressor.
9
QUICK HELP
Changing a wheel

161
Bipper_en_Chap09_aide-rapide_ed02-2014
Front lamps
Open the bonnet. to access the bulbs, reach
behind the headlamp unit.
Remove the protective covers to gain
access to the bulbs.
Carry out the operations in reverse order to
refit each bulb.
CHANGING A BULB
Types of bulb
Various types of bulb are fitted on your
vehicle.
to remove them:
1.


T
ype A


e ntirely glass bulb: pull gently as it is
fitted by pressure.
2.

T
ype B
Bayonet bulb: press on the bulb then turn


it anticlockwise.
3.

T
ype C
Cylindrical bulb: move aside the contacts.
4.


T
ype D - E
Halogen bulb: release the retaining


spring from its housing.
High pressure washing
When using this type of washing on
stubborn dirt, do not persist very long on
the headlamps, or on other lamps and their
edges to avoid damaging their coating and
seals.
9
QUICK HELP
Changing a bulb

162
Bipper_en_Chap09_aide-rapide_ed02-2014
1 - Dipped beam headlamps
T
ype D, H4 - 55 W
-

Remove the cover by turning it

anticlockwise.
-

Disconnect the electrical connector
.
-

Release the retaining spring by pressing

on the two clips.
-

Change the bulb taking care to align the

metal part with the grooves on the lamp.
2 - Sidelamps
T

ype A, W 5 W - 5 W
-

Remove the cover by turning it

anticlockwise.
-

Pull the bulb holder to gain access to the

bulb.
-

Change the bulb. 3 - Main beam headlamps
T

ype D, H4 - 55 W
-

Remove the cover by turning it

anticlockwise.
-

Disconnect the electrical connector
.
-

Release the retaining spring by pressing

on the two clips.
-

Remove the bulb holder
.
-

Change the bulb taking care to align the

metal part with the groove on the lamp. 4 - Direction indicators
T

ype B, PY 21 W - 21 W amber
- t
urn the bulb holder a quarter turn

anticlockwise.
-
Remove the bulb by pressing it lightly

while turning it anticlockwise.
-
Change the bulb.
If you encounter any dif
ficulty, consult a
P euge O t
dealer or a qualified workshop.
When each operation has been

completed, check the operation of the
lamps.
5 - Foglamps
T

ype E, H1 - 55 W
Contact a P
euge O t
dealer or a qualified

workshop.
Changing a bulb