153
The system is reactivated automatically every time the engine is started by
t
he driver.
Reactivation
Press this button again.
Operating fault
Have it checked by a CITROËN dealer or a q ualified w orkshop.
In
the event of a fault in STOP mode, the
v
ehicle may stall.
All of the instrument panel warning lamps come on.Depending on version, an alert message may also be displayed, asking you to place the gear
s
elector lever on position N and put your foot
o
n the brake pedal.
It
is then necessary to switch off the ignition
a
nd start the engine again using the "START/
STOP"
button.In
t
he
e
vent
o
f
a
f
ault
w
ith
t
he
s
ystem,
t
he symbol for the button changes
t
o alert mode and the warning lamp
f
lashes for a few moments then
c
omes on continuously.
The
system
is
active
again;
this
is
c
onfirmed
by
the
indicator
lamp
in
the
b
utton
going
off
and
illumination
of
t
his
symbol.
The Stop & Start system makes use of
a
dvanced technology. For any work on
t
he system go to a qualified workshop
w
ith the skills and equipment required,
w
hich a CITROËN dealer is able to
pro
vide.
Before
doing anything under the
b
onnet, deactivate the Stop & Start
s
ystem to avoid any risk of injury
r
esulting from automatic operation of
S
TART mode.
Maintenance
This system requires a 12 V battery with a special specification and technology (reference
n
umbers available from CITROËN dealers).
Fitting
a battery not listed by CITROËN
i
ntroduces the risk of malfunction of the
s
ystem.
For
charging, use a 12 V charger and do not
r
everse the polarity.
4
Driving
159
Steering mounted controls
6. Speed limiter on / pause indication.
7. S peed limiter mode selection indication.
8.
S
peed value setting.
Speed limiter
System which prevents the vehicle from exceeding the speed programmed by the driver.
The speed limiter cannot, in any circumstances, replace the need to o
bserve speed limits, nor can it replace the
n
eed for vigilance on the part of the driver.
Once the programmed speed limit is reached, additional pressure on the accelerator pedal
h
as no effect.
1.
S
peed limiter mode selection wheel.
2.
V
alue decrease button.
3.
V
alue increase button.
4.
S
peed limiter on / pause button.
5.
L
ist of memorised speeds display button.Displays in the instrument panel
The speed limiter is switched on manually: i
t requires a programmed speed of at least
2
0 mph (30 km/h).
The
speed limiter is paused by operation of the
control.
The
programmed speed can be exceeded
t
emporarily by pressing the accelerator firmly
b
eyond the point of resistance.
To
return to the programmed speed, simply
r
elease the accelerator pedal until the vehicle
r
eturns to the programmed speed limit.
The
programmed speed remains in the
m
emory when the ignition is switched off.For
more information on the list of memorised
s
peeds, refer to the "Memorising speeds"
s
ection.
4
Driving
162
Steering mounted controls
6. Cruise control pause / resume indication.
7. C ruise control mode selection indication.
8.
S
peed value setting.
Cruise control
System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.
The cruise control system cannot, in any circumstances, replace the need to observe speed limits, nor can it replace the need for vigilance on the part of the driver.
Y ou are advised to keep your feet near the pedals at all times.
The cruise control is switched on manually: it r
equires a minimum vehicle speed of 25 mph
(
40 km/h) and engagement of:
-
f
ourth gear or higher on a manual gearbox,
-
s
econd gear or higher in manual mode on
a
n electronic or automatic gearbox,
-
p
osition A on an electronic gearbox or D on
an
automatic gearbox. 1.
C
ruise control mode selection wheel.
2.
D
ecrease speed setting or set the current
s
peed as the cruise setting.
3.
I
ncrease speed setting or set the current
s
peed as the cruise setting.
4.
C
ruise control pause / resume button.
5.
M
emorised speeds display button.Displays in the instrument panel
Switching off the ignition cancels any programmed speed value.
The cruise control is paused
manually or
b
y
pressing the brake or clutch pedal or
o
n
triggering of the ESP system for safety
r
easons.
It
is
possible to exceed the programmed speed
t
emporarily by pressing the accelerator pedal.
To
return to the programmed speed, simply
r
elease the accelerator pedal until the
p
rogrammed cruise speed is reached again.
For more information on the list of memorised s
peeds, refer to "Memorising speeds" section.
Driving
166
The active cruise control is switched on
manually: it requires that the speed of the vehicle b
e between 25 mph (40 km/h) and 90 mph
(
150 km/h), as well as the engagement of:
-
f
ourth gear or higher with a manual
g
earbox,
-
s
econd gear or higher with an electronic or
a
utomatic gearbox in manual mode,
-
p
osition A with an electronic gearbox or D
with
an automatic gearbox.
General points
The active cruise control can above be paused
using the control, or automatically:
-
b
y pressing the brake or clutch pedal,
-
i
n the event of operation of the ESC, for
s
afety reasons,
-
i
n the event of operation of the electric
p
arking brake control lever,
-
w
hen an inter-vehicle time threshold is
r
eached (calculated according to the
r
elative speeds of your vehicle and the
v
ehicle in front and the inter-vehicle time
se
tting
c
hosen),
-
w
hen the distance between your vehicle
a
nd the one in front becomes to small,
-
w
hen the speed of the vehicle in front is
to low,
-
w
hen the speed of your vehicle becomes
t
oo low. The active cruise control cannot in any
circumstances
replace the observation
o
f speed limits, nor the need for
v
igilance on the part of the driver.
It
i
s
r
ecommended that
y
ou always
k
eep
y
our feet close to the pedals.
If
the
speed
setting
selected
is
above
9
3
mph
(150
km/h),
the
system
switches
t
o
standard
cruise
control
operation
(
a
message
appears
in
the
instrument
pan
el). The
inter-vehicle time setting is
m
emorised on switching off the ignition.
driving
176
Lane departure warning system
System which, using a camera which recognises solid or broken lines, detects the
i
nvoluntary crossing of longitudinal traffic lane
m
arkings on the ground.
To
provide safe driving, the camera analyses
t
he image then, if the driver's attention drops,
t
riggers a warning if the vehicle drifts over
a
lane marking (speed higher than 50 mph
(
80 km/h)).
This
system is particularly useful on motor ways
a
nd main roads. Activation
and deactivation of the function is
d
one in the "
Driving assistance " menu of the
t
ouch screen tablet.
Activation / deactivation
The driver is alerted by vibration of the seat belt (
at the level of the reel).
No
warning is transmitted while the direction
i
ndicator is active and for approximately
2
0 seconds after the direction indicator is
s
witched off.
Detection - alert
The lane departure warning system cannot, in any circumstances, replace
t
he need for vigilance and responsibility
o
n the part of the driver. F
Press this button, the indicator lamp c
omes on. The function is activated
The detection may be impeded:
- i f the markings on the ground are
w
orn,
-
i
f there is little contrast between the
m
arkings on the ground and the
r
oad sur face,
-
i
f the windscreen is dirty,
-
i
n
c
ertain
se
vere
w
eather
c
onditions:
f
og, heavy rain, snow, bright sunlight
o
r direct exposure to the sun (low
s
un, leaving a tunnel, ...) and shade.
In
the event of a fault, the symbol
f
or the button changes to alert
m
ode and the warning lamp flashes
f
or a few moments then goes off.
Operating fault
Contact a CITROËN dealer or a qualified w
orkshop.
The
status
of
the
system
remains
in
the
m
emory
when
the
ignition
is
switched
off.
It
is
necessary
to
observe
the
driving
r
egulations
and
to
take
a
break
every
t
wo
hours. F
P
ress
this
button
again,
the
i
ndicator
lamp
goes
off.
The
f
unction
is
deactivated
Driving
179
F To deactivate the system, press t
his button again; its indicator
l
amp goes off as well as the
a
ssociated indicator in the
in
strument
pan
el. In
the event of a fault, the symbol for t
he button changes to alert mode and
t
he warning lamp flashes for a few
m
oments then goes off.
Operating fault
Have it checked by a CITROËN dealer or a qualified w orkshop.
The
system
is
automatically
deactivated
w
hen
towing
with
a
towbar
approved
by
CIT
ROËN. The
system may suffer temporary
i
nterference in certain weather
conditions (rain, hail...).
In particular, driving on a wet sur face
o
r moving from a dry area to a wet area
c
an cause false alerts (for example, the
p
resence of a fog of water droplets in t
he blind spot angle is interpreted as a v
ehicle).
In
bad or wintry weather, ensure that
t
he sensors are not covered by mud, ice
o
r snow.
Take
care not to cover the warning zone
i
n the door mirrors or the detection
z
ones on the front and rear bumpers
w
ith adhesive labels or other objects;
t
hey may hamper the correct operation
o
f the system.
The
state
of
the
system
remains
in
memory
on
s
witching
off
the
ignition.
High pressure jet wash
When
washing your vehicle, direct the
l
ance at least 30 cm away from the
sen
sors.
4
Driving
192
The system is deactivated by pressing the control.
The
system is deactivated automatically:
-
o
n switching off the ignition,
-
i
f the engine stalls,
-
i
f no manoeuvre is started within 5 minutes
o
f selection of the type of manoeuvre,
-
a
fter a prolonged stop of the vehicle during
a
manoeuvre,
-
i
f the road wheel anti-slip regulation (ASR)
i
s
t
riggered,
-
i
f the speed of the vehicle exceeds the
s
tated limit,
-
w
hen the driver interrupts movement of the
s
teering
w
heel,
-
a
fter 4 manoeuvre cycles,
-
o
n opening the driver's door,
-
i
f one of the front wheels encounters an
o
bstacle.
The
operation indicator lamp goes off in the
i
nstrument panel and a message is displayed
a
ccompanied by an audible signal.
The
driver should then take back control of the
v
ehicle's
s
teering.
Deactivation
The system is switched off automatically:
- w hen towing a trailer,
-
i
f the driver's door is opened,
-
i
f the speed of the vehicle is above 42 mph
(
70 km/h).
To
switch the system of for a prolonged period,
c
ontact a CITROËN dealer or a qualified
w
orkshop.
In the event of a fault with the system, this warning lamp is displayed in the i
nstrument panel and a message appears,
a
ccompanied by an audible signal.
Operating faults
In the event of a fault, the symbol for the button changes to alert
m
ode and the warning lamp flashes
f
or a few moments then goes off.
Contact
a
CITROËN dealer or a qualified
w
orkshop.
Switching off
If the lateral distance between your vehicle a nd the space is too great, the system may n
ot be able to measure the space.
Anything
projecting beyond the envelope
o
f the vehicle (long or wide load) is not
t
aken into account by the Park Assist
s
ystem during a manoeuvre.
In
bad weather or in winter, ensure that
t
he sensors are not covered by road
d
irt, ice or snow.
In
the event of a fault, have the system
c
hecked by a CITROËN dealer or a
q
ualified
w
orkshop.
If
the
system
is
deactivated
during
a
m
anoeuvre,
the
drive
should
reactivate
i
t
to
repeat
the
measurement. The
indicator
lamp
for
the
function
f
lashes
for
a
few
seconds.
If
the
fault
occurs
during
the
use
of
t
he
system,
the
indicator
lamp
goes
o
f f.
Driving
196
Operation of the rear foglamps is inhibited with the tailgate open.
Opening
the boot when these lamps are
o
n causes them and their indicator lamp
i
n the instrument panel to go off.
They
do not come back on
a
utomatically when the boot is closed:
t
hey must be switched on again using
t
he control stalk. In
good or rainy weather, by both day a
nd night, the front foglamps and the
r
ear foglamps are prohibited. In these
s
ituations, the power of their beams
m
ay dazzle other drivers. They should
o
nly be used in fog or falling snow.
In
these weather conditions, you should
s
witch on the foglamps and dipped
b
eam headlamps manually, as the
s
unshine sensor may detect sufficient
l
ight.
Do
not forget to switch off the front and
r
ear foglamps when they are no longer
n
ecessary.Switching off the lighting
when switching off the ignition
When the ignition is switched off, all of the lamps switch off immediately, except for the d
ipped beam headlamps if automatic guide-
me-home
lighting is activated.
Switching on the lighting when
switching on the ignition
To reactivate the lighting control stalk, turn the ring A to position "0"
- lighting off, then t
o the position of your choice.
If
the lighting is switched on manually after
s
witching off the ignition, there is an audible
s
ignal when a front door is opened to warn
t
he driver that they have forgotten to switch
o
ff the vehicle's lighting, with the ignition off.
They
switch off automatically after a period
w
hich depends on the state of charge of the
b
attery (entry to energy economy mode).
Visibility