2014.5 Citroen C4 CACTUS RHD clutch

80
Starting
The parking brake must be applied.
F
 
W

ith
 
a   manual   gearbox,   place   the   gear  
l

ever
 
in   neutral   then   depress   the   clutch  
p

edal
 f
ully.
F
 
W

ith
 
an   electronic   gearbox,   place   the  
c

ontrol at N   then   press   the   brake   pedal  
f

i r m l y.
F
 
I

nsert
  the   key   into   the   ignition   switch;   the  
s

ystem   recognises   the   code.
In
 
certain   cases,   you   may   have   to   apply  
m

ore   force   to   the   steering   (wheels   on  
f

ull
  lock,   for   example).
F
 
W

ith
 
a   petrol   engine,   operate   the   starter  
m

otor
  by   turning   the   key   to   position   3
without
  pressing   the   accelerator   pedal,  
u

ntil
 
the   engine   starts.   Once   the   engine   is  
r

unning,   release   the   key. F
 W ith   a   Diesel   engine,   turn   the   key   to  
p

osition 2,
  ignition   on,   to   operate   the  
eng

ine
 p
re-heating
 s
ystem.
Wait until this warning lamp goes off in the instrument   panel   then   operate   the   starter m

otor   by   turning   the   key   to   position 3
without
  pressing   the   accelerator   pedal,
 u

ntil   the   engine   starts.   Once   the   engine   is
 r

unning,   release   the   key.
In wintry conditions, the warning lamp can   stay   on   for   a   longer   period.   When  
t

he   engine   is   hot,   the   warning   lamp  
d

oes   not   come   on. In
  temperate   conditions,   do   not   leave  
t

he   engine   at   idle   to   warm   up   but   move  
o

ff   straight   away   and   drive   at   moderate  
s

peed.
Never   leave   the   engine   running   in  
a

n   enclosed   area   without   adequate  
v

entilation:
 in
ternal
 c
ombustion
 e

ngines   emit   toxic   exhaust   gases,  
s

uch   as   carbon   monoxide.   Danger   of  i
ntoxication   and   death.
In   very   severe   wintry   conditions  
(

temperatures   below   -23°C),   to   ensure  
t

he   correct   operation   and   durability   of  
t

he   mechanical   components   of   your  
v

ehicle,   engine   and   gearbox,   it   is  
n

ecessary   to   leave   the   engine   running  
f

or   4   minutes   before   moving   off.
If
  the   engine   does   not   start   straight  
a

way,   switch   off   the   ignition.   Wait   a   few  
m

oments   before   operating   the   starter  
m

otor   again.   If   the   engine   does   not  
s

tart   after   several   attempts,   do   not   keep  
t

rying:   you   risk   damaging   the   starter  
m

otor   or   the   engine.
Contact
  a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
F
 
U

nlock
 
the
 
steering
 
column
 
by
 
simultaneously
 t

urning
 
the
 
steering
 
and
 
the
 
key.
Driving

83
5-speed manual gearbox
Engaging reverse gear
F Press  the   clutch   pedal   fully   down.
F  P ush   the   gear   lever   fully   to   the   right   then  
ba

ckwards. Only
  engage   reverse   gear   when   the
 v

ehicle   is   stationary   with   the   engine   at   idle.
As   a   safety   precaution   and   to   facilitate  
s

tarting   of   the   engine:
-  
a
lways   select   neutral,
-  
p
ress   the   clutch   pedal.
5
Driving

86
N flashes in the instrument panel, accompanied   by   an   audible   signal   and  
a

  message   if   the   control   N has not been
pressed
  for   starting.
Press control N
  to   select   neutral.
Moving off
F Switch  on   the   ignition.
F  S elect   neutral   (control   N).
 T

he   indicator   lamp   for   the   control   comes   on.
F
 
P
ress   the   brake   pedal   fully.
F
 
S
tart   the   engine. N
  appears   in   the   instrument   panel.
F  
S
elect   for ward   drive   (control   D)
  or   reverse  
(c

ontrol
 R). T

he   associated   indicator   lamp   comes   on   in  
t

he   control   panel.
D
  and   1 or R   appear   in   the   instrument  
pan

el.Creep function
This function allows the vehicle to be
manoeuvred  more   easily   at   low   speeds   (when  
p

arking,   in   traffic   jams...).
After
  pressing   control   D or R, the vehicle
moves as soon as you take your foot off the
brake pedal ,
  at   low   speed   and   with   the   engine  
a

t   idle.
The
  creep   function   may   be   temporarily  
u

navailable   if   the   clutch   temperature   is  
t

oo   high   or   the   slope   too   steep.
Do
  not   leave   children   unsupervised  
i

nside   the   vehicle   when   the   engine   is  
r

unning.
You
 
must
 
keep
 
your
 
foot
 
on
 
the
 
brake
 
p

edal
 
while
 
starting
 
the
 
engine.
The
 
"Foot
 
on
 
the
 
brake"
 
warning
 
and
 
t

he
 
associated
 
control
 
panel
 
indicator
 
l

amp
 
flash
 
if
 
the
 
brake
 
pedal
 
is
 
not
 
p

ressed
 
when
 
starting
 
the
 
engine.
Press
 
firmly
 
on
 
the
 
brake
 
pedal. F
 
R

elease
 
the
 
parking
 
brake.
F
 
P

rogressively
 
take
 
your
 
foot
 
off
 
the
 
brake
 
ped

al.
 T

he
 
vehicle
 
moves
 
off.
Driving

87
Never select neutral (position N)   when  m
oving.
Forward drive
F Press control D . T
he   indicator   lamp   in   the   control   comes   on.
D
  and   the   gear   engaged   appear   in  
t

he   instrument   panel.
The
  gearbox   then   operates   in   auto-adaptive  
m

ode,   without   any   action   on   the   part   of   the  
d

river.   It   continuously   selects   the   most   suitable  
g

ear   taking   account   of:
-
 
o
ptimisation   of   fuel   consumption,
-
 
d
riving   style,
-
 
r
oad   conditions,
-
 
v
ehicle   load.
For
  optimum   acceleration,   when  
ov

ertaking   another   vehicle   for   example,  
p

ress   the   accelerator   pedal   fully   down,  
b

eyond   the   point   of   resistance.
Temporary control of gear
changing
You can temporarily take over control of gear changes   using   the   steering   mounted   "+"  and "-"
control
  paddles:   if   the   engine   speed   allows,   the
 g

ear   change   is   carried   out.
This function allows you to anticipate certain
situations
 
s
uch  
a
s  
ov
ertaking  
a
nother  
v
ehicle  
o
r  
a

pproaching   a   bend.
After
  a   few   moments   without   any   action   on   the  
p

addles,   the   gearbox   resumes   control   of   gear  
c

hanging
 a
utomatically. To
  engage   reverse,   the   vehicle   must   be  
i

mmobilised   with   your   foot   on   the   brake.
F
P
ress control R
.
 T
he   indicator   lamp   in   the   control   comes   on.
Reverse
There is an audible signal on enga
gement o f r everse.
If
 
reverse   gear   is   requested   when   moving,  
t

he

N
 
warning   lamp   flashes   and   the   gearbox  
g

oes
 
into   neutral   automatically.
To
 
engage   reverse,   stop   the   vehicle   then,   with  
y

our
 
foot   on   the   brake   pedal,   press   control   N,
then R .
Do
 
not
 
press
 
the
 
brake
 
and
 
accelerator
 
p

edals
 
at
 
the
 
same
 
time:
 
this
 
could
 
c

ause
 
very
 
rapid
 
wear
 
of
 
the
 
clutch.
5
Driving

90
Stop & Start
Operation
Going into engine STOP mode
The "ECO"  warning   lamp   comes   on i
n   the   instrument   panel   and   the   engine g

oes   into   standby   automatically:
-
 
w

ith a manual gearbox , when stationary,
in
 
neutral,   and   you   release   the   clutch  
ped

al.
-
 
w

ith an electronic gearbox , when
stationary
  or   at   speeds   below   5   mph  
(

8 km/h)   (depending   on   version),   in   neutral  
(

control   on   N)
  or   when   you   press   the   brake  
ped

al. Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   button.
For
  your   comfort,   during   parking  
m

anoeuvres,   STOP   mode   is   not  
a

vailable   for   a   few   seconds   after  
c

oming   out   of   reverse   gear.
STOP
  mode   does   not   affect   the   the  
v

ehicle's   systems,   such   as   for   example,  
b

raking,   power   steering...
Special cases: STOP mode not
available
STOP mode is not invoked principally when:
-  t he   vehicle   is   on   a   steep   slope   (rising   or  
f

alling),
-
 
t
he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(

10 km/h)   since   the   last   engine   start   by   the  
d

river,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case, the "ECO"
 

warning  
l

amp   flashes   for   a   few   seconds   then  
g

oes off.
This operation is perfectly normal.
The
 
Stop
 
&
 
Start system
 
puts
 
the
 
engine
 
temporarily
 
into
 
standby
 
-
 
STOP
 
mode
 
-
 
during
 
stops
 
in
 
the
 
traffic   (red   lights,   traffic   jams,  
or
 
other...).
 
The engine
 
restarts
 
automatically
 
-
 
START
 
mode
 
-
 
as
 
soon
 
as
 
you
 
want
 
to
 
move
 
off.
 
The
 
restart   takes   place   instantly,   quickly  
and
 
silently.
Per fect
 
for
 
urban
 
use,
 
the
 
Stop
 
&
 
Start
 
system
 
reduces
 
fuel
 
consumption
 
and
 
exhaust
 
emissions
 
as
 
well
  as   the   noise   level   when  
stationary.
Stop & Start time counter
A cumulative time counter for periods i n   STOP   mode   during   a   journey.
It
 
is
 
displayed   in   the   trip   computer   (accessible  
v

ia the " Driving assistance "
  menu   of   the  
t

ouch
 
screen   tablet).
It resets to zero every time the ignition is switched on.
driving

91
Going into engine START mode
The "ECO" warning   lamp   goes   off  a
nd   the   engine   starts   automatically:
-
 
w

ith a manual gearbox , when you fully
depress
  the   clutch   pedal.
-
 
w

ith an electronic gearbox:
●
 
c

ontrol  
o
n  
D,

 
w
hen  
y
ou  
r
elease  
t
he  
b
rake  
ped

al,
●
 
c

ontrol   on   N   and   brake   pedal   released,  
w

hen you press control D ,
●
 w

hen
 y
ou
 enga
ge
 r
everse. START
  mode   is   invoked   automatically   when:
-  y ou   open   the   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   7   mph  
(

11 km/h)   with   an   electronic   gearbox,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   for   control   of   a   system.
Special cases: START invoked
automatically
In this case the "ECO" warning   lamp  f
lashes   for   a   few   seconds,   then   goes  
o

f f.
This operation is perfectly normal. Before
  doing   anything   under   the  
b

onnet,   deactivate   the   Stop   &   Start  
s

ystem   to   avoid   any   risk   of   injury  
r

esulting   from   automatic   operation   of  
S

TART   mode.
This   system   requires   a   12   V   battery   with   a  
s

pecial   specification   and   technology   (reference  
n

umbers   available   from   CITROËN   dealers).
Fitting   a   battery   not   listed   by   CITROËN  
i

ntroduces   the   risk   of   malfunction   of   the  
s

ystem.
For   charging,   use   a   12   V   charger   and   do   not  r
everse   the   polarity.
Maintenance
The Stop & Start system makes use of a
dvanced   technology.   For   any   work   on  
t

he   system   go   to   a   qualified   workshop  
w

ith   the   skills   and   equipment   required,  
w

hich   a   CITROËN   dealer   is   able   to  
pro

vide.
5
Driving

98
Flashing of the dashes indicates a fault with the cruise   control.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating fault Switching off
F Turn wheel 1 to the "0" p osition. T
he   display   of   information   related   to   the  
c

ruise   control   disappears. When
  the   cruise   control   is   switched   on,  b
e   careful   if   you   maintain   the   pressure  o
n   one   of   the   programmed   speed  
c

hanging   buttons:   this   may   result   in   a  
v

ery   rapid   change   in   the   speed   of   your  
v

ehicle.
do n

ot use the cruise control on
slippery
  roads   or   in   heavy   traffic.
On
  a   steep   descent,   the   cruise   control  
w

ill not be able to prevent the vehicle
from
  exceeding   the   programmed   speed.
On
  steep   climbs   or   when   towing,   the  
p

rogrammed   speed   may   not   be   reached  
o

r   maintained.
The
  use   of   mats   not   approved   by  
C

ITROËN   may   inter fere   with   the  
o

peration   of   the   cruise   control.
To
  avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
n
ever   fit   one   mat   on   top   of   another.
It
 
is
 
possible
 
to
 
exceed
 
the
 
programmed
 
speed
 
t

emporarily
 
by
 
pressing
 
the
 
accelerator
 
pedal.
To
 
return
 
to
 
the
 
programmed
 
speed,
 
simply
 
r

elease
 
the
 
accelerator
 
pedal
 
until
 
the
 
p

rogrammed
 
cruise
 
speed
 
is
 
reached
 
again.
Exceeding the programmed
speed
Once switched on, you can pause the cruise c ontrol   at   any   time   by   pressing   button   4:   the  
s

creen   confirms   the   pause.
Pause
If the programmed speed is exceeded, the   displayed   speed   flashes.
Once
  the   speed   of   the   vehicle   returns  
t

o   the   programmed   speed   setting,   the  
d

isplay   becomes   steady   again.
The cruise control is paused
 m

anually
 o

r   by   pressing   the   brake   or   clutch   pedal  
o

r   if   the   ESP   system   is   invoked   for  
s

afety   reasons.
Driving

103
Park Assist
This system provides active assistance with parking, detecting a parking space then controlling the steering to park in the space.
I t   controls   the   steering   while   the   driver   manages   the   accelerator,   brakes,   gears   and   clutch   (manual   gearbox).   During   phases   of   entry   into   and   exit   from  
a

  parking   space,   the   system   provides   visual   and   audible   information   to   the   driver   in   order   to   make   the   manoeuvre   safe.   It   may   be   necessary   to   move  
f

or wards   and   backwards   more   than   once.
The
  Park   Assist   system   cannot   in   any  
c

ircumstances   replace   the   need   for  
v

igilance   on   the   part   of   the   driver.
The
  driver   must   remain   in   control   of  
t

heir   vehicle   ensuring   that   the   space  
r

emains   clear   during   the   manoeuvre.
In
  some   circumstances,   the   sensors  
m

ay   not   detect   small   obstacles   located  
i

n   their   blind   spots. Changing
  tyre   sizes   (out-size   tyres,  
w

inter   tyres,   ...)   can   inter fere   with  
t

he   correct   operation   of   the   parking  
a

ssistance   system.
During
  a   manoeuvre   the   steering   wheel  
t

urns   quickly:   do   not   hold   the   steering  
w

heel,   do   not   place   your   hand   between  
t

he   spokes   of   the   steering   wheel   and  
t

ake   care   with   loose   and   bulky   clothing,  
s

carves,   handbags...   There   is   a   risk   of  
in

jury. For
  entry   into   a   parking   space   (parallel  
p

arking)   the   system   does   not   detect  
s

paces   which   are   clearly   much   smaller  
o

r   larger   than   the   size   of   the   vehicle.
This
  "parking   assistance"   system  
i

s   activated   automatically   during  
m

anoeuvres;   it   is   therefore   possible  
t

hat   a   symbol   comes   on   in   the   screen,  
a

ccompanied   by   an   audible   signal,  
w

ithout   affecting   the   manoeuvre.The
  selection   of   the   type   of   manoeuvre  
(

entering   or   exiting   a   parallel   parking  
s

pace)   prevents   a   change   to   STOP  
m

ode   of   Stop   &   Start.
In
  STOP   mode,   this   selection   restarts  
t

he
 eng
ine.
The
  driver   can   take   control   at   any   time   by   gripping   the   steering   wheel.
The
 
s
ystem  
p
rovides  
a
ssistance  
i
n  
e
ntering  
a
nd  
e

xiting
 a par
king
 spa
ce
 w
hen
 par
allel
 par
king.
5
D