119
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
Front airbags
The front airbags are fitted in the centre of the steering wheel for the
driver and in the dashboard for the
front passenger.
d
eployment
They are deployed, except the
passenger's front airbag if it has been
deactivated, in the event of a serious
front
impact applied to all or part of the
front
impact zone A in the longitudinal
centreline of the vehicle on a horizontal
plane
directed from the front towards
the
rear of the vehicle.
The
front airbag inflates between the
front occupant of the vehicle and the
dashboard to cushion their forward
movement.
d
eactivationo
nly the passenger's front airbag can
be deactivated:
-
with the ignition switched off
,
insert
the key into the passenger's
front airbag deactivation switch,
-
turn it to the of
f "OFF" position,
-
then
remove the key, keeping the
switch
in the new position.
The passenger's front
airbag
warning lamp in the
instrument
panel is on while
the
airbag is deactivated.If
the two airbag warning lamps
are on continuously
, do not install
a rear-facing child seat, contact
a
CITROËN dealer or a qualified
workshop.
Front airbag fault
T
o ensure the safety of your child,
it is essential to deactivate the
passenger's front airbag when you
install a rear-facing child seat on the
front
passenger seat. Otherwise, the
child
would
risk
being
kille
d
or
seriously
injured
if the airbag were to inflate.
r
eactivation
In the "OFF" position, the passenger's
front airbag will not be deployed in the
event of an impact.
As soon as the child seat is removed,
turn the airbag switch to the
"O n "
position to re-activate the passenger's
front airbag and so ensure the safety
of your passenger in the event of an
impact.
If this warning lamp comes on,
accompanied by an
audible
signal and a message
in the screen, contact a
CITR
o Ë n dealer or a
qualified
workshop to have
the
system checked.
airbags
SaFETY
5
Berlingo_2_VP_en_Chap06_Accessoire_ed02-2014
137
OtHEr AccESSOrIES
These accessories and parts, having
been tested and approved for reliability
and safety, are all adapted to your
vehicle.
A
wide range of recommended
accessories and genuine parts is
available.
a further range is also available,
structured
around comfort, leisure and
maintenance:
Anti-theft
alarm, window etching, first
aid
kit, high visibility vest, front and
rear
parking sensors, warning triangle,
security
bolts for alloy wheels, ...
Seat
covers compatible with airbags
for the front seats, bench seat, rubber
mats,
carpet
mats,
snow
chains,
blinds,
tailgate
bicycle carrier, ...
To
prevent the mat from becoming
caught
under the pedals:
-
ensure
that the mat and its fixings
are positioned correctly
,
-
never
fit one mat on top of another.Audio
equipment, hands-free kit,
speakers,
CD changer, satellite navigation
system, USB box, V ideo kit, ...
Regardless
of the audio and telematic
equipment
offered on the market, the
technical constraints associated with
the
fitting of equipment of these product
groups
mean that the special features
of
the equipment and its compatibility
with the capacities of your vehicle's
standard
equipment must be taken into
account.
Please ask a CITROËN dealer
for
more information before fitting such
equipment.
Maximum weights on bars
-
T
ransverse bars on longitudinal
bars:
75 Kg (these bars are not
compatible
with the Modutop roof).Installing radiocommunication
transmitters
You are advised to contact a CITR
o Ë n
dealer before installing accessory
radiocommunication
transmitters with
external
aerial on your vehicle.
The
CITROËN dealer network
will
inform you of the specification
(frequency
band, maximum output
power
, aerial position, specific
conditions of installation) of the
transmitters
which can be fitted, in
accordance with the Motor V
ehicle
Electromagnetic
Compatibility
Directive
(2004/104/EC).
Front
mud flaps, rear mud flaps,
15/17 inch
alloy wheels, wheelarch
trim,
leather steering wheel, ...
Screenwash, interior and exterior
cleaning
and maintenance products,
spare
bulbs, ...
Equipment
AccESSOrIES
6
Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
159
The temporary tyre repair kit consists of a compressor and a bottle
(containing
a sealant).
using the kit
1. Tick the deflated wheel on the speed
limitation sticker then affix
the
sticker to the vehicle's steering
wheel
to remind you that a wheel is
in
temporary use.
2.
Clip the bottle
1 on the
compressor 2.
3.
Connect the bottle
1 to the valve of
the
tyre to be repaired.
4.
T
ake care to unwind the
compressor
pipe before connecting
it
to the bottle.
5.
Connect the power lead to one of
the
vehicle's 12V sockets.
6.
Switch
on the compressor by
pressing button
A until the tyre
pressure
reaches 2.0 bars. If this
pressure cannot be reached, the
tyre
cannot be repaired.
7.
Remove
and store the compressor.
8.
Drive
immediately, for a few miles
(kilometres),
at reduced speed,
to
fill the puncture.
9.
Adjust
the pressure using the
compressor
in accordance with the
recommendation
for
the
vehicle
and
check
that the leak is filled correctly
(no
further loss of pressure).
10.
Drive
at reduced speed (50 mph
[80
km/h]).
The
tyre must be
examined
and repaired by a
specialist
as soon as possible.
a
fter use, the bottle can be stored in
a plastic bag, supplied in the kit, to avoid staining your vehicle with traces
of
fluid.
Warning:
the bottle of gel contains
ethylene-glycol, a product which
is
harmful if swallowed and which
causes
irritation to the eyes.
Keep
it out of reach of children.
a
fter use, do not discard the bottle into
the
environment, take it to a CITROËN
dealer or to an specialised waste
disposal
site.
Replacement
bottles of sealant are
available
from CITROËN dealers.
PuncturE rEPAIr KIt
The kit is located in one of the two storage compartments located under
the
front seats.
Vehicles
supplied with a temporary
puncture
repair kit do not have a spare
wheel
or tooling (jack, wheelbrace, ...).
Changing a wheel
QUICk HELP
8
Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
176
FuSES undEr tHE BOnnEt
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
the fuses. Fuses
F Amperes Aa
llocation
1 20 Engine
management
2 15 Horn
3 10 Front
and rear wash-wipe pump
4 20 Headlamp
wash pump
5 15 Engine
components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
switch, clutch switch
8 25 Starter
9 10Headlamp
beam motor, parc management unit
10 30 Engine
components
11 40 Spare
12 30 Wipers
13 40 Built-in
systems interface
14 30 Pump
15 10 Right-hand
main beam headlamp
16 10Left-hand
main beam headlamp
17 15Right-hand
dipped beam headlamp
18 15 Left-hand
dipped beam headlamp
Changing a fuse
Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
178
Without lifting (4 wheels on the
road)
You should always use a towing bar.
BEInG tOWEd
Ths procedure involves the use of the
towing eye supplied with the tools for
changing
a wheel.
From the front
- Unclip the cover by pressing the
bottom part.
-
Fully
screw in the removable towing
eye.
From the rear
- Unclip the cover using a coin or the
flat part of the towing eye.
-
Fully
screw in the removable towing
eye. When towing with the engine
switched
off, there is no braking or
steering
assistance.
Lifting (only 2 wheels on the
road)
It is preferable to raise the vehicle
using
professional lifting equipment.
Vehicles fitted with a manual
gearbox (d iesel version)
In the case of vehicles fitted with a manual gearbox, the gear lever
must
be in neutral, failure to observe
this
special condition may result in
damage
to transmission and braking
components
and the absence of
braking
assistance when the engine is
started
again.
Chapter
9,
"Changing
a
wheel"
section.
Having your vehicle towed
07
10.36
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
By alphabetical list
Press r A d IO, select the station of your
choice
and confirm.
By automatic frequency search
Press 7 or 8
for the automatic search
for
a lower or higher radio frequency.
Or
turn the thumb wheel at the steering
mounted
controls.
By manual frequency search
Press 5 or 6
to adjust the radio
frequency
step by step.
Selecting a station
The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS station tracking mode. This phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audio system.
The
quality of reception is represented by the number of
active
waves in this symbol.
Press
r A d IO or OK to display the
contextual
menu.
changing waveband
Select "change waveband".
Select " AM / FM" and confirm.
rAdIO
07
10.37
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
Press the button on the numerical keypad to recall a preset station.
Or
press then turn the thumb wheel at the steering
mounted
controls.
Presetting a station
after selecting a station, press one of the buttons
on the numerical keypad for 2 seconds to preset the
current
station.
An
audible signal confirms that the station has been
preset. Press
r A d IO.
Activate / d
eactivate rd S
RDS, if activated, allows you to continue listening to the same station
by automatic retuning to alternative frequencies. However,
in
certain conditions, coverage of an RDS station may not be
assured throughout the entire country as radio stations do not
cover
100 % of the territory.
This
explains the loss of reception of
the
station during a journey.
Select "Guidance options " then
confirm.
a
ctivate or deactivate " rd S" then
confirm.
rAdIO