2014.5 Citroen BERLINGO MULTISPACE RHD bulb

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
168
cHAnGInG A BuLB
type A
All   glass   bulb:   pull   gently  
as

  it   is   fitted   by   pressure.
High pressure washing
Open the bonnet. T o   access   the   bulbs,  reach
  behind   the   headlamp   unit.
Carry out the operations in reverse
order
  to   refit   each   bulb   and   check   that  
the

  bonnet   is   closed   securely.type c
Halogen

  bulb:   release   the  
retaining

  spring   from   its  
housing.
type B
Bayonet
  bulb:   press  
on the bulb then turn it
anticlockwise.
Halogen
  bulbs   must   be   changed  with
  the   headlamp   off.   Wait   a   few  
minutes

  (risk   of   serious   burns).  
d
o not touch the bulb directly with your
fingers,
  use   lint-free   cloths.
It
  is   normal   for   condensation   to   form  
inside

  the   headlamps.   Regular   use   of  
the

  vehicle   eliminates   this   misting.The
  bulbs   must   be   changed   with  
the ignition of

f or with the battery
disconnected.   Wait   approximately  
3 minutes

  after   changing   the   bulb  
before

  reconnecting   the   battery.
Check   that   the   lamps   operate   correctly  
after

  each   operation.
When using this type of washing
on stubborn dirt, do not persist on
the   headlamps,   the   lamps   and   their  
edges

  to   avoid   damaging   their   coating  
and

  seals.
types of bulb
Various types of bulb are fitted to your vehicle.
 T o   remove   them:
type

d
Light

  emitting   diode  
(LED):

  for   replacement  
of

  the   daytime   running  
lamps,

  contact   a  
CITR

o Ë n dealer or a
qualified
  workshop.
Changing a bulb

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
169
3. d irection indicators
type B

,   PY21W   -   21W   (amber)
-
 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-
 
T
urn   the   bulb   holder   a   quarter  
turn

  anticlockwise.
-
 
Remove
  the   bulb   by   pressing  
it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure
correct

  sealing.
2.
Sidelamps


type A

, W5W - 5W
-
 
Remove

 
the
 
cover
 
by
 
pulling
 
the
 
flexible

 
rubber
 
tab.
-
 
Remove

 
the
 
bulb
 
holder
 
fitted
 
by
 
pressure

 
by

 
pullin

g
 
the

 
connector

.
-
 
Change

 
the
 
bulb.
-
 
Ensure

 
that
 
the
 
cover
 
is
 
refitted
 
correctly all round to assure
correct

 
sealing.
FrOnt LAMPS
1. d ipped / Main beam headlamps
type

c , H4 - 55W
-
 
Remove
  the   centre   cover   by  
pullin

g   the   flexible   rubber   tab.
-
d isconnect the electrical
connector.
-
 
Release
  the   retaining   tab.
-
 
Change
  the   bulb   taking   care  
to

  align   the   metal   part   with   the  
grooves

  on   the   lamp.
-
 
Reposition
  the   retaining   tab.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure
correct

  sealing.
Changing a bulb
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
170
4. Foglamps type
c , H1 - 55W
-
 
Remove
  the   three   clips   and   the  
screw securing the wheelarch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheelarch   liner   upwards.
-
 
Remove
  the   foglamp   by   removing  
the screw

, which can be accessed
via the hole provided for this
purpose
  in   the   bumper,   using   a  
T

orx
© 30 screwdriver.
-
 Unclip   the   foglamp   by   squeezing  
the

 
clip   to   release   it.
-

Remove the foglamp from the outside.- Turn the yellow cover a 1/4 turn to open.- Separate the clips which secure
the base of bulb on each side to
release   the   bulb.
-
 
Remove
  the   bulb   by   pulling,  
keeping

  it   straight.
-

Insert the new bulb, reposition the
clips around the base of the bulb
and carry out the operations in
reverse

  order   to   put   the   lamp   unit  
and

  the   bumper   back   in   position.
SIdE rEPEAtE r
type A,   WY5W   -   5W   (amber)
-
Push the repeater towards the rear
and disengage it by pullin

g the
front.
-

Contact a CITR
o Ë n dealer to
obtain a new repeater which is a
sealed
  component.
-
 
T
o   refit,   engage   the   repeater  
towards the rear and bring it
towards

  the   front.
cOurtESY LAMPS
type A, 12V5W - 5W
-
Unclip the lens by sliding a
screwdriver in the slots on each
side

  of   the   courtesy   lamp.
-
 
Pull
  the   bulb   out   and   change   it.
-

Clip the lens in its housing and
ensure

  that   it   is   secured   correctly.
Front /
r ear
Changing a bulb

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
171
rEAr LAMPS
This procedure requires the use of the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the supply
wire correctly to avoid trapping


the
  wire.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time  
is
  above   2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
concerning
 
the
 bulbs,
 
refer
 
to
 
the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


type B

,
 
P21/5W
 
-
 
21/5W
2.
d
irection indicators
type B

,
 
PY21W
 
-
 
21W
 
(amber)
3.
r
eversing lamps
type B

, P21W - 21W
4.

Foglamps


type B

, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the faulty bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
Changing a bulb
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
172
nuMBEr PLAtE LAMPS
- Unscrew  the   two   nuts.
-  
Push
  the   pins.
-

If necessary
, disconnect the
connector
  to   remove   the   lamp.
-
 
Change
  the   bulb.
With tailgate
-
d
isengage the plastic lens using a
screwdriver.
-
 
Change

 
the
 
bulb.
-

Replace the plastic lens and press
on

 
it.
tHIrd BrAKE LAMP
type A ,   W16W   -   16W
With hinged doors
-
 
Unclip

 
the
 
interior
 
trim.
-
d
isconnect the connector by
moving
 
aside
 
its
 
tab.
-
 
T

urn
 
the
 
bulb
 
holder
 
a
 
quarter
 
turn
 
anticlockwise.
-

 
Change

 
the
 
bulb.
-
 
Put

 
the
 
bulb
 
holder
 
back
 
in
 
place
 
and

 
reconnect
 
the
 
connector.
-
 
Put

 
the
 
trim
 
back
 
in
 
place.type A
, W5W - 5W
Changing a bulb