Page 107 of 140
8-26
8
EBU24394Checking the front brake lever free play The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever should have no
free play as shown. If there is free play, have a
Yamaha dealer check the brake system.EBU24593Checking the brake pedal height The brake pedal height must be checked and, if
necessary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart. The top of the brake pedal should be positioned
50.2 mm (1.98 in) above the top of the frame as
shown. If the brake pedal is not positioned as spec-
ified, have a Yamaha dealer adjust it.
EBU24715Adjusting the parking brake free play The parking brake free play must be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
Cable length “A” should measure 64–68 mm
(2.52–2.68 in). Adjust the parking brake free play
as follows.
1. No brake lever free play
1. Brake pedal height
U1BS63E0.book Page 26 Tuesday, March 13, 2012 11:43 AM
Page 108 of 140
8-27
81. Release the parking brake by moving the
parking brake lever to the right.
2. Fully loosen the locknut and the adjusting bolt at the rear brake caliper.
3. Slide the rubber cover back at the brake ca- ble.
4. Loosen the locknut.
5. Turn the parking brake free play adjusting nut in direction (a) to increase the cable length,
and in direction (b) to decrease it.
TIPIf the cable length cannot be adjusted to specifica-
tion, consult a Yamaha dealer.6. Tighten the locknut on the brake cable.
7. Slide the rubber cover to its original position.
8. Turn in the adjusting bolt at the rear brake cal-iper until it feels tight, then turn it out 1/8 turn
and tighten its locknut to the specified torque.
NOTICE: When tightening the locknut,
1. Locknut
2. Adjusting bolt
3. Cable length “A”
1. Locknut
2. Parking brake free play adjusting nut
3. Rubber cover
1
2
(a) (b)
3
U1BS63E0.book Page 27 Tuesday, March 13, 2012 11:43 AM
Page 131 of 140
10-1
10
EBU25961
SPECIFICATIONS
Dimensions:Overall length:1780 mm (70.1 in)
Overall width: 1095 mm (43.1 in)
Overall height:
1080 mm (42.5 in)
Seat height: 820 mm (32.3 in)
Wheelbase: 1210 mm (47.6 in)
Ground clearance:
115 mm (4.5 in)
Minimum turning radius: 3100 mm (122 in)Weight:With oil and fuel:
180.0 kg (397 lb)Noise and vibration level:Noise level (77/311/EEC):YFM35RD 84.3 dB(A)@3500 r/min
A-weighted sound power level:
YFM35RD 94.0 dB(A)@3500 r/min
Vibration on seat (EN1032, ISO5008): YFM35RD Will not exceed 0.5 m/s²
Vibration on handlebar (EN1032, ISO5008): YFM35RD Will not exceed 2.5 m/s²
Engine:Engine type:Air cooled 4-stroke, SOHC
Cylinder arrangement: Single cylinder
Displacement:
349 cm³
Bore × stroke:
83.0 × 64.5 mm (3.27 × 2.54 in)
Compression ratio: 9.20 : 1
Starting system:
Electric starter
Lubrication system: Wet sumpEngine oil:Recommended brand:
YAMALUBE
U1BS63E0.book Page 1 Tuesday, March 13, 2012 11:43 AM
Page 135 of 140
10-5
10
EBU30401For Europe only
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required.
Factors that influence the actual level of exposure
of work-force include the characteristics of the
work room, the other sources of noise, etc. i.e. the
number of machines and other adjacent process-
es, and the length of time for which an operator is
exposed to the noise. Also the permissible expo-
sure level can vary from country. This information,
however, will enable the user of the machine to
make a better evaluation of the hazard and risk.U1BS63E0.book Page 5 Tuesday, March 13, 2012 11:43 AM
