2013 YAMAHA GRIZZLY 125 belt

Parking on a slope ..................................... 6-5
Accessories and loading ............................ 6-6
RIDING YOUR ATV ...................................... 7-1 GETTING TO KNOW YOUR ATV............... 7-2
RIDE WITH CARE AND GOOD JUDGMENT .............................................. 7-2
BE CAREFUL WHERE YOU RIDE ............. 7-9
TURNING YOUR ATV .............................. 7-12
CLIMBING UPHILL ................................... 7-14
RIDING DOWNHILL.................................. 7-16
CROSSING A SLOPE............................... 7-17
CROSSING THROUGH SHALLOW WATER ................................................... 7-18
RIDING OVER ROUGH TERRAIN ........... 7-20
SLIDING AND SKIDDING ......................... 7-20
WHAT TO DO IF... .................................... 7-22
WHAT TO DO... ........................................ 7-22
PERIODIC MAINTENANCE AND
ADJUSTMENT ............................................... 8-1 Owner’s manual and tool kit ....................... 8-2
Periodic maintenance chart for the emission control system ................ 8-3
General maintenance and lubrication chart ......................................................... 8-5
Checking the spark plug ............................. 8-9 Engine oil ..................................................8-11
Transmission oil ........................................8-14
Cleaning the engine and V-belt case air
filter elements .........................................8-17
Cleaning the spark arrester ......................8-23
V-belt case drain screw ............................8-24
Adjusting the carburetor ............................8-25
Adjusting the engine idling speed .............8-26
Adjusting the throttle lever free play .........8-26
Valve clearance ........................................8-27
Brakes .......................................................8-28
Checking the front and rear brake shoes ......................................................8-28
Adjusting the front brake lever free play ...8-29
Adjusting the rear brake lever free play ....8-33
Drive chain slack .......................................8-34
Lubricating the drive chain ........................8-37
Checking and lubricating the cables .........8-37
Checking and lubricating the front and rear brake levers .....................................8-38
Checking the wheel hub bearings .............8-39
Lubricating the lower arm pivots ...............8-39
Lubricating the front knuckle pivots ..........8-40
Lubricating the steering shaft ....................8-41
Battery ......................................................8-41
Replacing the fuse ....................................8-44
Replacing a headlight bulb .......................8-45
U1PY61E0.book Page 2 Wednesday, March 14, 2012 5:22 PM

7-19
7The ATV can be used to cross slow moving, shal-
low water of up to a maximum of 20 cm (8 in) in
depth. Before entering the water, choose your path
carefully. Enter where there is no sharp drop off,
and avoid rocks or other obstacles which may be
slippery or upset the ATV. Drive slowly and care-
fully.
Test your brakes after leaving the water. If neces-
sary, apply them several times to let friction dry out
the linings. Do not continue to ride your ATV with-
out verifying that you have regained proper braking ability.
WARNING! Wet brakes may have re-
duced stopping ability, which could cause loss
of control.
[EWB02621]
After riding your ATV in water, be sure to drain the
trapped water by removing the check hose at the
bottom of the air filter case. Also, remove the V-belt
case drain screw to drain any water that may have
accumulated. NOTICE: Undrained water can
cause damage or improper operation.
[ECB00841]
Wash the ATV in fresh water if it has been operat-
ed in salt water or muddy conditions.
U1PY61E0.book Page 19 Wednesday, March 14, 2012 5:22 PM

7-20
7
RIDING OVER ROUGH TERRAIN
WARNING
EWB01651Riding improperly over obstacles could cause
loss of control or a collision. Before operating
in a new area, check for obstacles. Never at-
tempt to ride over large obstacles, such as
large rocks or fallen trees. When you go over
obstacles, always follow proper procedures as
described in the Owner’s Manual.Riding over rough terrain should be done with cau-
tion. Look out for obstacles which could cause
damage to the ATV or could lead to an upset or ac-
cident. Be sure to keep your feet firmly mounted on
the footboards at all times. Avoid jumping the ATV
as loss of control and damage to the ATV may re-
sult.
SLIDING AND SKIDDING
WARNING
EWB01662Skidding or sliding improperly may cause you
to lose control of this ATV. You may also re-
gain traction unexpectedly, which may cause
the ATV to overturn.
1. Air filter case check hose
1. V-belt case drain screw
1
1
U1PY61E0.book Page 20 Wednesday, March 14, 2012 5:22 PM

8-5
8
EBU21865General maintenance and lubrication chart TIP●For ATVs not equipped with an odometer or an hour meter, follow the month maintenance intervals.●For ATVs equipped with an odometer or an hour meter, follow the km (mi) or hours maintenance inter-
vals. However, keep in mind that if the ATV isn’t used for a long period of time, the month maintenance
intervals should be followed.●Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools,
data and technical skills.NO.ITEM CHECK OR MAINTENANCE
JOB INITIAL
EVERY
Whichev- er comes first month136612
km
(mi) 320
(200) 1300
(800) 2500
(1600) 2500
(1600) 5000
(3200)
hours 20 80 160 160 320
1 Engine and V-belt
case air filter ele-
ment Clean and replace if necessary.
Every 20–40 hours (more often in wet or
dusty areas)
2 *Front brake Check operation and correct if necessary.
Check brake lever free play and adjust if neces-
sary. √√√√√
Replace brake shoes. Whenever worn to the limit
3 *Rear brake Check operation and correct if necessary.
Check brake lever free play and adjust if neces-
sary. √√√√√
Replace brake shoes. Whenever worn to the limit
U1PY61E0.book Page 5 Wednesday, March 14, 2012 5:22 PM

8-17
8
EBU2384CCleaning the engine and V-belt case air
filter elements Both air filter elements should be cleaned at the
specified intervals in the periodic maintenance
chart.
Engine air filter elementTIPThere is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.
1. Place the ATV on a level surface.
2. Remove the seat. (See page 4-10.)
3. Remove the breather hose by pulling it out,
and then loosen the air filter joint screw.
4. Remove the air filter case cover by removing its screws, then disconnecting the air filter
case cover from the air filter joint.
1. Air filter case check hose
1
1. Breather hose
2. Air filter joint
3. Air filter joint screw
1
3
2
U1PY61E0.book Page 17 Wednesday, March 14, 2012 5:22 PM

8-20
8
13. Install the air filter element into the air filter
case. NOTICE: Make sure that the air filter
element is properly seated in the air filter
case. Never operate the engine with the air
filter element removed. This will allow un-
filtered air to enter the engine, causing rap-
id engine wear and possible engine
damage. Additionally, operation without
the air filter element will affect carburetor
jetting with subsequent poor performance
and possible engine overheating.
[ECB00461]
14. Connect the air filter case cover to the air filter joint. 15. Install the air filter case cover by installing the
screws, and then tighten the air filter joint
screw.
16. Install the breather hose.
17. Install the seat.
TIPThe air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated more
often if the ATV is operated in extremely dusty ar-
eas. Each time the air filter element maintenance
is performed, check the air inlet of the air filter case
for obstructions. Check the air filter case rubber
joint to the carburetor fittings and the rubber joint
manifold fittings for an air-tight seal. Tighten all fit-
tings securely to avoid the possibility of unfiltered
air entering the engine.V-belt case air filter element 1. Place the ATV on a level surface.
2. Remove the front carrier by removing the bolts.
1. Washer
1
U1PY61E0.book Page 20 Wednesday, March 14, 2012 5:22 PM

8-24
8
4. Insert the tailpipe into the muffler and align the
screw holes.
5. Check the gaskets for damage, and replace them if necessary.
6. Install the screws and their gasket, and then tighten the screws to the specified torque.
WARNING
EWB02340Do not start the engine when cleaning the
spark arrester, otherwise it could cause injury
to the eyes, burns, carbon monoxide poison-
ing, possibly leading to death, and start a fire.
Always let the exhaust system cool prior to
touching exhaust components.EBU30061V-belt case drain screw After riding in water deep enough to allow it to en-
ter the V-belt case, remove this screw to drain the
water from the case.TIPIf water drains from the V-belt case after removing
the screw, have a Yamaha dealer check the ATV
as the water may affect other engine parts.
1. Tailpipe screw
2. Gasket
3. Tailpipe
4. Spark arresterTightening torque:Tailpipe screw:7 Nm (0.7 m·kgf, 5.1 ft·lbf)
3
4 21
U1PY61E0.book Page 24 Wednesday, March 14, 2012 5:22 PM

8-25
8To drain the water from the V-belt case
1. Place the ATV on a level surface.
2. Place a container under the V-belt case, and then remove the V-belt case drain screw and
its gasket to drain the water from the V-belt
case.
3. Install the V-belt case drain screw and its new gasket, and then tighten the screw to the
specified torque.
EBU23940Adjusting the carburetor The carburetor should be checked and, if neces-
sary, adjusted at the intervals specified in the peri-
odic maintenance and lubrication chart. The
carburetor is an important part of the engine and
requires very sophisticated adjustment. Therefore,
most carburetor adjustments should be left to a
Yamaha dealer, who has the necessary profes- sional knowledge and experience. The adjustment
described in the following section, however, may
be performed by the owner as part of routine main-
tenance.NOTICEECB00480The carburetor has been set and extensively
tested at the Yamaha factory. Changing these
settings without sufficient technical knowl-
edge may result in poor performance of or
damage to the engine.
1. V-belt case drain screw
2. Gasket
12
Tightening torque: V-belt case drain screw:7 Nm (0.7 m·kgf, 5.1 ft·lbf)
U1PY61E0.book Page 25 Wednesday, March 14, 2012 5:22 PM