2013 VOLKSWAGEN PASSAT turn signal bulb

Lights
up Possible cause Proper response
 One or more driving lights not working or
cornering light malfunction.
Replace burned out bulb or
if all light bulbs are OK, see an authorized
Volkswagen dealer or authorized
Volkswagen Service facility.
Fog lights switched on (indicator light on
the headlight switch).



Left or right turn signal.
The indicator light blinks twice as fast if a
turn signal is not working on the vehicle or
the trailer.
Check the turn signals on the vehicle and
the trailer.
' Daytime running lights (DRL) on.
$2,
 High beams switched on or headlight
flashers in use.

When the ignition is switched on, several warning and indicator lights come on briefly for a function
check. They go out after a few seconds.
WARNING
Failure to heed warning lights and instrument cluster text messages can cause the vehicle to
break down in traffic and result in a collision and serious personal injury.
x Never ignore warning lights or text WARNINGS.
x Always stop the vehicle as soon as it is safe to do so.
x Whenever stalled or stopped for repair, move the vehicle a safe distance off the road, stop
the engine, turn on the emergency flashers, and use other warning devices to warn approach-
ing traffic.
x Never park the vehicle in areas where the hot catalytic converter and exhaust system can
come into contact with dry grass, brush, spilled fuel, oil, or other material that can catch fire.
x A broken down vehicle presents a high accident risk for itself and others. Switch on
emergency flashers and set up a warning triangle to warn oncoming traffic.
NOTICE
Failure to heed warning lights or text WARNINGS can result in vehicle damage.
High Intensity Discharge (HID) headlights provide bright, uniform lighting to help you see and be
seen. The light comes from an electric arc between two electrodes in the gas-filled bulb. Over time, the
electrodes can wear down and the gap between them will get wider. The HID lamp’s control unit then
increases the voltage to keep the arc’s brightness constant. However, the commonly called “Xenon”
bulbs will also ultimately burn out. Before they burn out, HID lamps can flicker. A message will then
appear in the MFI. This is your reminder to see an authorized Volkswagen dealer or an authorized
Volkswagen Service facility to check the headlights.

Replacing headlight bulbs

Fig. 216 In the engine compartment: Covers in the left headlight assembly: A Side marker light, B Low beam
headlight, C High beam headlight,>Turn signal and parking light, E Daytime running light.

Fig. 217 In the wheel housing: Removing cover.

⇒ fig. 216 (A) (B) (C) (D) (E)
Side marker
light
Low beam High beam Turn signal
and parking
light
Daytime
running lights
3.
Unscrew the
fastening screw
⇒ fig. 217
(arrow) with a
short
screwdriver. To
access the
screw, turn the
wheel in
question inward
as shown in .

Same as column
(A).
4.
Remove the
cover from the
wheel house
lining .
Same as column
(A).
5. On the back of the headlight assembly, pull off the rubber cover for
the bulb you are replacing.
Turn plastic
cover ⇒ fig. 216
A (E)
counterclockwise
and remove.
6. Left side of the
vehicle: Turn
plastic bulb
socket
counterclockwise
(about 1/8 turn)
to release it.
Right side of the
vehicle: Turn
plastic bulb
socket clockwise
(about 1/8 turn)
instead.
Turn plastic bulb
socket
counterclockwise
(about 1/8 turn)
to release it.
Press plastic
tab on back of
bulb socket to
release it.
Same as
column (A).
Same as column
(A).
7. Pull plastic bulb socket assembly back and out of the headlight assembly.
8. Replace the burned out light bulb with a new bulb of the same type.
9. Reinsert the bulb socket assembly into the headlight assembly.

⇒ fig. 216 (A) (B) (C) (D) (E)
Side marker
light
Low beam High beam Turn signal
and parking
light
Daytime
running lights
10. Left side of the
vehicle: Turn
plastic bulb
socket clockwise
until it locks into
place in the
headlight
assembly.
Right side of the
vehicle: Turn
plastic bulb
socket
counterclockwise
instead.
Turn plastic bulb
socket clockwise
until it locks into
place in the
headlight
assembly.
Push bulb
socket into
the headlight
assembly
until you hear
it “click” into
place.
Same as
column (A).
Same as column
(A).
11. Replace rubber cover on the back of the headlight assembly for the
bulb you replaced.
Place the plastic
cover A (E) in
the headlight
assembly
housing and turn
clockwise as far
as it will go.
12.
Place the cover
⇒ fig. 217 in the
wheel housing
liner and use the
screwdriver in
the vehicle tool
kit to tighten the
fastening screw
(arrow).

Same as column
(A).
Please carry out each step only in the order specified:
The illustrations show the left headlight assembly from the rear. The right headlight assembly is
the mirror image of the left headlight assembly.