2013 TOYOTA YARIS HYBRID display

266 2-1. Driving procedures
YARIS_F (including HV)_WE_52D27E
CAUTION
Gear Shift Indicator display
Refer to the display while considering actual traffic and road conditions. Fail-
ure to exercise judgment may lead to an accident.
NOTICE
To prevent damage to the transmission (vehicles with a 6-speed trans-
mission)
Do not lift up the ring section except when shifting the lever to R.
Shift the shift lever to R only when the vehicle is stationary.
Do not shift the shift lever to R without
depressing the clutch pedal.

273 2-2. Instrument cluster
2
When driving
YARIS_F (including HV)_WE_52D27E
Hybrid vehicle
Tachometer
Displays the engine speed in revolutions per minute.
Speedometer
Displays the vehicle speed.
Clock
P. 426
Outside temperature display
P. 427
Fuel gauge
Displays the quantity of fuel remaining in the tank.
Display change button
P. 285
Odometer, trip meter and multi-information display
P. 284
Clock adjusting buttons
P. 426
Hybrid System Indicator
Displays hybrid system power output and regenerative level

274 2-2. Instrument cluster
YARIS_F (including HV)_WE_52D27E
The meters and display operate when
Except hybrid vehicle
Vehicles without a smart entry & start system:
The engine switch is in the “ON” position.
Vehicles with a smart entry & start system:
The “ENGINE START STOP” switch is in IGNITION ON mode.
Hybrid vehicle
Vehicles without an electronic key:
The engine switch is in the “ON” position.
Vehicles with an electronic key:
The “POWER” switch is in ON mode.
Hybrid System Indicator
By keeping the indicator needle within Eco area, more Eco-friendly driv-
ing can be achieved.
Charge area indicates regeneration
* status. Regenerated energy will be
used to charge the battery.
*: When used in this manual, “regeneration” refers to the conversion of
energy created by the movement of the vehicle into electrical energy.
Power area
Shows that the driving power is more
than the upper limit of Eco driving.
Eco area
Shows that the vehicle is driven Eco-
friendly.
Hybrid Eco area
Shows that the vehicle is driven in a
condition that promotes frequent
motor-only operation. (When the vehi-
cle is operating with low driving load,
such as when driving slowly, using
Hybrid Eco area leads Eco-friendly
driving.)
Charge area
Shows regenerative charging.

276
2-2. Instrument cluster
YARIS_F (including HV)_WE_52D27E
Indicators and warning lights
The indicators and warning lights on the instrument cluster and cen-
ter panel inform the driver of the status of the vehicle’s various sys-
tems.
For the purpose of explanation, the following illustration displays all
indicators and warning lights illuminated.
Except hybrid vehicle
Instrument cluster (vehicles without a tachometer type A):
Instrument cluster (vehicles without a tachometer type B):

284
2-2. Instrument cluster
YARIS_F (including HV)_WE_52D27E
Multi-infor mation display
The multi-information display presents the driver with a variety of
driving-related data.
Odometer (P. 285)
Trip meter (P. 286)
Stop & Start system opera-
tion time (if equipped)
(P. 286)
Stop & Start system total
operation time (if equipped)
(P. 287)
Trip information (P. 285)
Displays driving range, fuel
consumption and other cruis-
ing-related information.
Instrument panel light con-
trol (P. 289)
Eco Driving Indicator Light
customization (except
hybrid vehicle [if equipped])
(P. 289)
EV indicator customization
(hybrid vehicle) (P. 290)

285 2-2. Instrument cluster
2
When driving
YARIS_F (including HV)_WE_52D27E
Changing the display
Items displayed can be switched
by pressing the display change
button.
Display items
Odometer
Ty p e ADisplays the total distance the vehicle has been
driven.
Ty p e B

286 2-2. Instrument cluster
YARIS_F (including HV)_WE_52D27ETr ip m eter
Stop & Start system operation time (if equipped) Ty p e ADisplays the distance the vehicle has been driven
since the meter was last reset. Trip meters A and
B can be used to record and display different dis-
tances independently.
Pressing and holding the display change button will
reset the trip meter that is currently displayed.
Ty p e B
Ty p e C
Ty p e ADisplays the amount of time the engine was
stopped due to operation of the Stop & Start sys-
tem during the current trip.
Vehicles without a smart entry & start system:
From the engine switch in the “ON” position to the
engine switch in the “LOCK” position.
Vehicles with a smart entry & start system:
From the “ENGINE START STOP” switch in IGNI-
TION ON mode to the “ENGINE START STOP”
switch off. Ty p e B

287 2-2. Instrument cluster
2
When driving
YARIS_F (including HV)_WE_52D27EStop & Start system total operation time (if equipped)
Instantaneous fuel consumption
Average fuel consumption Ty p e ADisplays the total amount of time that the engine
has been stopped due to operation of the Stop &
Start system since the system was last reset.
Press and hold the button to reset.Ty p e B
Ty p e ADisplays instantaneous fuel consumption.
Ty p e B
Ty p e ADisplays the average fuel consumption since the
function was reset.
• The function can be reset by pressing and holding
the display change button when the average fuel
consumption is displayed.
• Use the displayed average fuel consumption as a
reference.
Ty p e B