2013 TOYOTA PRIUS V bulb

1
2
3
4
5
6
7
5
PRIUS v_OM_OM47820U_(U)
4-1. Maintenance and careCleaning and protecting the vehicle exterior............ 350
Cleaning and protecting the vehicle interior............. 354
4-2. Maintenance Maintenance requirements ..................... 357
General maintenance.......... 360
Emission inspection and maintenance (I/M)
programs........................... 364
4-3. Do-it-yourself maintenance Do-it-yourself service precautions ....................... 365
Hood ................................... 368
Positioning a floor jack ........ 371
Engine compartment ........... 374
12-volt battery ..................... 386
Tires .................................... 391
Tire inflation pressure ......... 400
Wheels ................................ 404
Air conditioning filter............ 407
Electronic key battery.......... 409
Checking and replacing fuses ................................. 411
Light bulbs........................... 422 5-1. Essential information
Emergency flashers............ 438
If your vehicle needs to be towed................................ 439
If you think something is wrong ............................... 445
5-2. Steps to take in an emergency
If a warning light turns on or a warning buzzer
sounds.............................. 446
If you have a flat tire ........... 464
If the hybrid system will not start ............................ 478
If you lose your keys........... 480
If the electronic key does not operate properly ......... 481
If the 12-volt battery is discharged........................ 483
If your vehicle overheats .... 489
If the vehicle becomes stuck ................................. 493
If your vehicle has to be stopped in an
emergency ....................... 495
4Maintenance and care5When trouble arises

194
2-1. Driving procedures
PRIUS v_OM_OM47820U_(U)
Tur n signal lever
■Turn signals can be operated when
The “POWER” switch is in ON mode.
■ If the indicator flashes faster than usual
Check that a light bulb in the front or rear turn signal lights has not burned
out.
The turn signal lever can be used to show the following intention of
the driver:
Right turn
Left turn
Lane change to the right
(push and hold the lever
partway)
The right hand signals will
flash until you release the
lever.
Lane change to the left
(push and hold the lever
partway)
The left hand signals will flash
until you release the lever.

Maintenance and care4
349
PRIUS v_OM_OM47820U_(U)
4-1. Maintenance and careCleaning and protecting the vehicle exterior ......... 350
Cleaning and protecting the vehicle interior .......... 354
4-2. Maintenance Maintenance requirements .................. 357
General maintenance....... 360
Emission inspection and maintenance (I/M)
programs ........................ 364
4-3. Do-it-yourself maintenance Do-it-yourself service precautions .................... 365
Hood ................................ 368
Positioning a floor jack ..... 371
Engine compartment ........ 374
12-volt battery .................. 386
Tires ................................. 391
Tire inflation pressure ...... 400
Wheels ............................. 404
Air conditioning filter......... 407
Electronic key battery....... 409
Checking and replacing fuses .............................. 411
Light bulbs........................ 422

366 4-3. Do-it-yourself maintenance
PRIUS v_OM_OM47820U_(U)
ItemsParts and tools
Engine oil level (P. 375)
• “Toyota Genuine Motor Oil” or
equivalent
• Rag or paper towel
• Funnel (used only for adding engine oil)
Fuses (P. 411)• Fuse with same amperage rating
as original
Light bulbs (P. 422)
• Bulb with same number and watt-
age rating as original
• Phillips-head screwdriver
• Flathead screwdriver
• Wrench
Radiator and condenser (P. 381)
Tire inflation pressure ( P. 400)• Tire pressure gauge
• Compressed air source
Washer fluid ( P. 384)
• Water or washer fluid containing
antifreeze (for winter use)
• Funnel (used only for adding water or washer fluid)

420 4-3. Do-it-yourself maintenance
PRIUS v_OM_OM47820U_(U)
■After a fuse is replaced
● If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. (P. 422)
● If the replaced fuse blows again, have the vehicle inspected by your
Toyota dealer.
■ If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
■ When replacing light bulbs
Toyota recommends that you use genuine Toyota products designed for this
vehicle. Because certain bulbs are connected to circuits designed to prevent
overload, non-genuine parts or parts not designed for this vehicle may be
unusable.
CAUTION
■To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage to the vehicle, and possibly a fire or
injury.
● Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
● Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
● Do not modify the fuses or fuse boxes.
■ Fuse box near the power control unit
Never check or replace the fuses as there are high voltage parts and wiring
near the fuse box.
Doing so may cause electric shock, resulting in death or serious injury.

422
4-3. Do-it-yourself maintenance
PRIUS v_OM_OM47820U_(U)
Light bulbs
You may replace the following bulbs by yourself. The difficulty level
of replacement varies depending on the bulb. As there is a danger
that components may be damaged, we recommend that replacement
is carried out by your Toyota dealer.
■Preparing for light bulb replacement
Check the wattage of the light bulb to be replaced. ( P. 508)
■ Front bulb locations
Front side
marker light
Headlight low beam
Daytime
running light and
headlight high beam
Fog light
Front turn
signal light
Parking light

423
4-3. Do-it-yourself maintenance
PRIUS v_OM_OM47820U_(U)
4
Maintenance and care
■
Rear bulb locations
Rear turn signal light
Back-up light License plate lights

424 4-3. Do-it-yourself maintenance
PRIUS v_OM_OM47820U_(U)
Replacing light bulbs■ Headlight low beams (halogen headlights)
Turn the bulb base counterclock-
wise.
Unplug the connector while
pressing the lock release.
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb
with the mounting, and insert.
STEP 1
STEP 2
STEP 3