2013 TOYOTA PRIUS PLUS light

443 4-3. Do-it-yourself maintenance
4
Maintenance and care
PRIUS +_OM_OM47841E_(EE)Unplug the connector while
pressing the lock release.
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb
with the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to
check that it is not loose, turn the
headlights on once and visually
confirm that no light is leaking
through the mounting.
STEP 2
STEP 3
STEP 4

444 4-3. Do-it-yourself maintenance
PRIUS +_OM_OM47841E_(EE)Front position lights
Turn the bulb base counterclockwise.
Vehicles with halogen headlights
Vehicles with LED headlights
Remove the light bulb.
When installing, reverse the steps listed.
STEP 1
STEP 2
STEP 3

445 4-3. Do-it-yourself maintenance
4
Maintenance and care
PRIUS +_OM_OM47841E_(EE)Front fog lights (if equipped)
Remove the fender liner bolts
and pull down the fender liner.
Unplug the connector while
pressing the lock release.
STEP 1
STEP 2

447 4-3. Do-it-yourself maintenance
4
Maintenance and care
PRIUS +_OM_OM47841E_(EE)Front turn signal lights
Remove the fender liner bolt and clip and pull down the fender
liner. (P. 445)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
STEP 1
STEP 2
STEP 3
STEP 4

448 4-3. Do-it-yourself maintenance
PRIUS +_OM_OM47841E_(EE)Rear turn signal lights and back-up/rear fog light
Open the back door and remove
the cover.
To prevent damage, cover the tip
of the screwdriver with a rag.
Turn the bulb base counterclock-
wise.
Rear turn signal light
Back-up/rear fog light
Remove the light bulb.
Rear turn signal light
Back-up/rear fog light
When installing, reverse the steps listed.
STEP 1
STEP 2
ITO43P147
STEP 3
STEP 4

449 4-3. Do-it-yourself maintenance
4
Maintenance and care
PRIUS +_OM_OM47841E_(EE)License plate lights
Open the back door and remove
the cover.
To prevent damage, cover the tip
of the screwdriver with a rag.
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
STEP 1
STEP 2
ITO43P150
STEP 3
STEP 4

450 4-3. Do-it-yourself maintenance
PRIUS +_OM_OM47841E_(EE)Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by
any authorized Toyota dealer or repairer, or another duly qualified
and equipped professional.
Headlight low beams (LED type)
Stop lights
Tail lights
Side turn signal lights
High mounted stoplight
Daytime running lights
LED lights
The headlight low beams (LED type), stop lights, tail lights, high mounted
stoplight and daytime running lights consist of a number of LEDs. If any of
the LEDs burn out, take your vehicle to any authorized Toyota dealer or
repairer, or another duly qualified and equipped professional to have the
light replaced.
Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does
not indicate a malfunction. Contact any authorized Toyota dealer or repairer,
or another duly qualified and equipped professional for more information in
the following situations:
Large drops of water have built up on the inside of the lens.
Water has built up inside the headlight.
When replacing light bulbs
P. 437

451 4-3. Do-it-yourself maintenance
4
Maintenance and care
PRIUS +_OM_OM47841E_(EE)
CAUTION
Replacing light bulbs
Be sure to stop the hybrid system and turn off the lights. Do not attempt to
replace the bulb immediately after turning off the lights.
The bulbs become very hot and may cause burns.
Do not touch the glass portion of the light bulb with bare hands. When it is
unavoidable to hold the glass portion, use and hold with a clean dry cloth
to avoid getting moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
Do not attempt to repair or disassemble light bulbs, connectors, electric
circuits or component parts.
Doing so may result in death or serious injury due to electric shock.
To prevent damage or fire
Make sure bulbs are fully seated and locked.