2013 TOYOTA iQ EV ECU

10
Charging equipment
Charging connector
Latch release button
CCID (Charging Circuit Interrupting Device)
Plug
Power indicator
Error warning indicator
Test button
Reset button
The charging cable included with the vehicle is designed to be connected only
to an AC 120V power source.
Charging indicator
Charging inlet light
Normal charging inlet
Charging inlet cap
Quick charging inlet (if equipped)
Normal charging cable
Recharge inlet door (charging port lid)
ELECTRIC VEHICLE SYSTEM
Charging
Step 1 Plug the charging cable into the outlet of the external power source.
NOTE: Hanging the CCID on a hook is recommended to reduce the strain on the
outlet and charging cable plug.
Step 2 Press the test button on the CCID to check that the electrical leakage detection function operates properly.
“While-in-use”
cover
The Scion iQ EV may be charged immediately, or scheduled to charge at a specific
time. Before charging, it is recommended that:
-Parking brake is securely set with shift position in “P”
-All lights are turned off
-The POWER switch is OFF
Start charging
2013Scion-iQ-EV.indd 101/14/13 6:48 PM

OVERVIEWELECTRIC VEHICLE SYSTEM FEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
11
Charging connector
Latch release button
CCID (Charging Circuit Interrupting Device)
Plug
Power indicator
Error warning indicator
Test button
Reset button
The charging cable included with the vehicle is designed to be connected only
to an AC 120V power source.Charging indicator
Charging inlet light
Normal charging inlet
Charging inlet cap
Quick charging inlet (if equipped)
Normal charging cable
Recharge inlet door (charging port lid)
Charging
Step 1 Plug the charging cable into the outlet of the external power source.
NOTE: Hanging the CCID on a hook is recommended to reduce the strain on the
outlet and charging cable plug.
- Make sure to hold the body of the
plug and insert it firmly into the
outlet.
- Check that the power indicator of the CCID (Charging Circuit
Interrupting Device) is illuminated.
- The surface of the CCID may become hot, but this does not
indicate a malfunction.
Step 2 Press the test button on the CCID to check that the electrical leakage detection function operates properly.
- If the error warning indicator illuminates when test button is
pressed, the function is operating
correctly.
- After the test is completed, press reset button to turn off the error
warning. Charging cannot occur
while error warning is illuminated.
- If the error warning indicator does not come on when test button is
pressed, the function may not be
operating correctly. Stop charging
immediately and contact your
Toyota or Scion dealer.
“While-in-use”
cover
The Scion iQ EV may be charged immediately, or scheduled to charge at a specific
time. Before charging, it is recommended that:
-Parking brake is securely set with shift position in “P”
-All lights are turned off
-The POWER switch is OFF
Start charging
2013Scion-iQ-EV.indd 111/14/13 6:48 PM

30
Emergency tire puncture repair kit
Refer to the Owner’s Manual for more details.
Tire Pressure Monitoring (warning)
System
After adjusting tire pressures, or after tires have been rotated or replaced, turn
the power switch to the “ON” mode and press and hold the “
SET” button until
indicator blinks three times. Let the vehicle sit for a few minutes to allow
initialization to complete.
Refer to the load label on the door jamb or the Owner’s Manual for tire inflation
specifications.
If the tire pressure indicator flashes for more than 60 seconds and then remains on,
take the vehicle to your local Toyota or Scion dealer.
NOTE: The warning light may come on due to temperature changes or changes in
tire pressure from natural air leakage. If the system has not been initialized
recently, setting the tire pressures to factory specifications should turn off the light.
If belt is fully extended, then retracted even slightly, it cannot be re-extended
beyond that point, unless fully retracted again. This feature is used to help hold
child restraint systems securely.
To find more information about seat belts, and how to install a child restraint
system, refer to the Owner’s Manual.
Keep as low on
hips as possible
Take up slack
Too high
Seat belts
Door locks
UnlockLock
Driver’s use
Front passenger’s use
UnlockLock
SAFETY AND EMERGENCY FEATURES
2013Scion-iQ-EV.indd 301/14/13 6:50 PM

31
OVERVIEWELECTRIC VEHICLE SYSTEM FEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
Emergency tire puncture repair kit
Refer to the Owner’s Manual for more details.
If tire pressure indicator is on, check/adjust each tire.
Tire Pressure Monitoring (warning)
System
After adjusting tire pressures, or after tires have been rotated or replaced, turn
the power switch to the “ON” mode and press and hold the “
SET” button until
indicator blinks three times. Let the vehicle sit for a few minutes to allow
initialization to complete.
Refer to the load label on the door jamb or the Owner’s Manual for tire inflation
specifications.
If the tire pressure indicator flashes for more than 60 seconds and then remains on,
take the vehicle to your local Toyota or Scion dealer.
NOTE: The warning light may come on due to temperature changes or changes in
tire pressure from natural air leakage. If the system has not been initialized
recently, setting the tire pressures to factory specifications should turn off the light.
Towing eyeletEmergency tire
puncture repair kitIf belt is fully extended, then retracted even slightly, it cannot be re-extended
beyond that point, unless fully retracted again. This feature is used to help hold
child restraint systems securely.
To find more information about seat belts, and how to install a child restraint
system, refer to the Owner’s Manual.
Take up slack
SAFETY AND EMERGENCY FEATURES
2013Scion-iQ-EV.indd 311/14/13 6:50 PM