2013 SUZUKI ALTO oil

7-26
INSPECTION AND MAINTENANCE
53MH0-74E
ALTO K10
53M-09-044
53M-09-045
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) – Blank
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) – Blank
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) 7.5AAutomated Manual Tran-
saxle 2 (if equipped)
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) 7.5A IG1 SIG
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
WA R N I N G
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period
of time, you may have a major electri-
cal problem. Have your vehicle
inspected immediately by your
MARUTI SUZUKI dealer.
EXAMPLE

7-27
INSPECTION AND MAINTENANCE
53MH0-74E
Bulb ReplacementInterior Light
53M-09-046
Pull down the lens by using a flat blade
screwdriver covered with a soft cloth as
shown. To install it, simply push it back in.
The bulb can be removed by simply pulling
it out. When replacing the bulb, make sure
that the contact springs are holding the
bulb securely.
Headlight
53M-09-049
Disconnect the coupler (1). Remove the
sealing rubber (2). Push the retaining
spring (3) forward and unhook it. Then
remove the bulb. Install a new bulb in the
reverse order.
CAUTION
• Light bulbs can be hot enough to
burn your finger right after being
turned off. This is true especially
for halogen headlight bulbs.
Replace the bulbs after they
become cool enough.
• The headlight bulbs are filled with
pressurized halogen gas. They can
burst and injure you if they are hit
or dropped. Handle them carefully.
NOTICE
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.
NOTICE
Frequent replacement of a bulb indi-
cates the need for an inspection of
the electrical system. This should be
carried out by your MARUTI SUZUKI
dealer.
EXAMPLEEXAMPLE

7-31
INSPECTION AND MAINTENANCE
53MH0-74E
NOTE:
When you install the metal retainers (3),
make sure the direction of metal retainers
as shown in the above illustrations.
5) Install the new blade in the reverse
order of removal, with the locked end
positioned toward the wiper arm.
Make sure the blade is properly
retained by all the hooks. Lock the
blade end into place.
6) Reinstall wiper frame to arm, making
sure that the lock lever is snapped
securely into the arm.Windshield Washer Fluid
Front
53M-09-066
Check that there is washer fluid in the tank.
Refill it if necessary. Use a good quality
windshield washer fluid, diluted with water
as necessary.
Air Conditioning System
If you do not use the air conditioner for a
long period, such as during winter, it may
not give the best performance when you
start using it again. To help maintain opti-
mum performance and durability of your air
conditioner, it needs to be run periodically.
Operate the air conditioner at least once a
month for one minute with the engine
idling. This circulates the refrigerant and oil
and helps protect the internal components.
WA R N I N G
Do not use “anti-freeze” solution in
the windshield washer reservoir. This
can severely impair visibility when
sprayed on the windshield, and also
damage your vehicle’s paint.
NOTICE
Damage may result if the washer
motor is operated with no fluid in the
washer tank.
EXAMPLE

8-7
EMERGENCY SERVICE
53MH0-74E
If the Engine Overheats
The engine could overheat temporarily
under severe driving conditions. If the high
engine coolant temperature warning light
comes on as overheating during driving:
1) Turn off the air conditioner, if equipped.
2) Take the vehicle to a safe place and
park.
3) Let the engine run at the normal idle
speed for a few minutes until the high
engine coolant temperature warning
light goes off.
If the high engine coolant temperature
warning light does not go off:
1) Turn off the engine and check that the
water pump belt and pulleys are not
damaged or slipping. If any abnormality
is found, correct it.2) Check the coolant level in the reservoir.
If it is found to be lower than the “LOW”
line, look for leaks at the radiator, water
pump, and radiator and heater hoses. If
you locate any leaks that may have
caused the overheating, do not run the
engine until these problems have been
corrected.
3) If you do not find a leak, carefully add
coolant to the reservoir and then the
radiator, if necessary. (Refer to “Engine
Coolant” in the “INSPECTION AND
MAINTENANCE” section.)
NOTE:
If your engine overheats and you are
unsure what to do, contact your MARUTI
SUZUKI dealer.
65D614
WA R N I N G
If you see or hear escaping steam,
stop the vehicle in a safe place and
immediately turn off the engine to let
it cool. Do not open the hood when
steam is present. When the steam
can no longer be seen or heard, open
the hood to see if the coolant is still
boiling. If it is, you must wait until it
stops boiling before you proceed.
WA R N I N G
• It is hazardous to remove the radia-
tor cap (or degassing tank cap for a
diesel engine) when the water tem-
perature is high, because scalding
fluid and steam may be blown out
under pressure. The cap should
only be taken off when the coolant
temperature has lowered.
• To help prevent personal injury,
keep hands, tools and clothing
away from the engine cooling fan
and air-conditioner fan (if
equipped). These electric fans can
automatically turn on without warn-
ing.

9-1
APPEARANCE CARE
53MH0-74E
Corrosion Prevention
It is important to take good care of your
vehicle to protect it from corrosion. Listed
below are instructions for how to maintain
your vehicle to prevent corrosion. Please
read and follow these instructions carefully.
Important Information About
Corrosion
Common causes of corrosion
1) Accumulation of road salt, dirt, mois-
ture, or chemicals in hard-to-reach
areas of the vehicle underbody or
frame.
2) Chipping, scratches and any damage to
treated or painted metal surfaces
resulting from minor accidents or abra-
sion by stones and gravel.
Environmental conditions which accel-
erate corrosion
1) Road salt, dust control chemicals, sea
air or industrial pollution will all acceler-
ate the corrosion of metal.
2) High humidity will increase the rate of
corrosion particularly when the tem-
perature range is just above the freez-
ing point.
3) Moisture in certain areas of a vehicle
for an extended period of time may pro-
mote corrosion even though other body
sections may be completely dry.
4) High temperatures will cause an accel-
erated rate of corrosion to parts of thevehicle which are not well ventilated to
permit quick drying.
This information illustrates the necessity of
keeping your vehicle (particularly the
underbody) as clean and dry as possible. It
is equally important to repair any damage
to the paint or protective coatings as soon
as possible.How to Help Prevent Corrosion
Wash your vehicle frequently
The best way to preserve the finish on your
vehicle and to help avoid corrosion is to
keep it clean with frequent washing. Wash
your vehicle at least once during the winter
and once immediately after the winter.
Keep your vehicle, particularly the under-
side, as clean and dry as possible. If you
frequently drive on salted roads, your vehi-
cle should be washed at least once a
month during the winter. If you live near the
ocean, your vehicle should be washed at
least once a month throughout the year.
For washing instructions, refer to the “Vehi-
cle Cleaning” section.
Remove foreign material deposits
Foreign material such as salts, chemicals,
road oil or tar, tree sap, bird droppings and
industrial fall-out may damage the finish of
your vehicle if it is left on painted surfaces.
Remove these types of deposits as quickly
as possible. If these deposits are difficult to
wash off, an additional cleaner may berequired. Be sure that any cleaner you use
is not harmful to painted surfaces and is
specifically intended for your purposes.
Follow the manufacturer’s directions when
using these special cleaners.
Repair finish damage
Carefully examine your vehicle for damage
to the painted surfaces. Should you find
any chips or scratches in the paint, touch
them up immediately to prevent corrosion
from starting. If the chips or scratches have
gone through to the bare metal, have a
qualified body shop make the repair.
Keep passenger and luggage compart-
ments clean
Moisture, dirt or mud can accumulate
under the floor mats and may cause corro-
sion. Occasionally, check under these
mats to ensure that this area is clean and
dry. More frequent checks are necessary if
the vehicle is used off road or in wet
weather.
Certain cargos such as chemicals, fertiliz-
ers, cleaners, salts, etc. are extremely cor-
rosive by nature. These products should
be transported in sealed containers. If a
spill or leak does occur, clean and dry the
area immediately.

9-3
APPEARANCE CARE
53MH0-74E
Carpets
Remove dirt and soil as much as possible
with a vacuum cleaner. Using a mild soap
solution, rub stained areas with a clean
damp cloth. To remove soap, rub the areas
again with a cloth dampened with water.
Repeat this until the stain is removed, or
use a commercial carpet cleaner for
tougher stains. If you use a carpet cleaner,
carefully follow the manufacturer’s instruc-
tions and precautions.
Cleaning the Exterior
Caring for Aluminum Wheels
NOTE:
• Do not use an acidic or alkaline deter-
gent to wash aluminum wheels. These
types of detergent will cause permanent
spots, discoloration and cracks on fin-
ished surfaces.
• Do not use a bristle brush and soap con-
taining an abrasive material. These will
damage finished surfaces.
Washing
60B212S
When washing the vehicle, park it where
direct sunlight does not fall on it and follow
the instructions below:
1) Flush the underside of body and wheel
housings with pressurized water to
remove mud and debris. Use plenty of
water.
2) Rinse the body to loosen the dirt.
Remove dirt and mud from the body
exterior with running water. You may
use a soft sponge or brush. Do not use
hard materials which can scratch the
paint or plastic. Remember that the
headlight covers or lenses are made of
plastic in many cases.
NOTICE
It is important that your vehicle be
kept clean and free from dirt. Failure
to keep your vehicle clean may result
in fading of the paint or corrosion to
various parts of the vehicle body.
WA R N I N G
• Never attempt to wash and wax
your vehicle with the engine run-
ning.
• When cleaning the underside of the
body and fender, where there may
be sharp-edged parts, you should
wear gloves and a long-sleeved
shirt to protect your hands and
arms from being cut.
• After washing your vehicle, care-
fully test the brakes before driving
to make sure they have maintained
their normal effectiveness.
EXAMPLE
NOTICE
When washing the vehicle:
• Avoid directing steam or hot water
of more than 80°C (176°F) on plas-
tic parts.
• To avoid damaging engine compo-
nents, do not use pressurized
water in the engine compartment.
NOTICE
To avoid damage to the paint or plas-
tic surface, do not wipe the dirt off
without ample water. Be sure to fol-
low above procedure.

9-4
APPEARANCE CARE
53MH0-74E
3) Wash the entire exterior with a mild
detergent or car wash soap using a
sponge or soft cloth. The sponge or
cloth should be frequently soaked in the
soap solution.
4) Once the dirt has been completely
removed, rinse off the detergent with
running water.
5) After rinsing, wipe off the vehicle body
with a wet chamois or cloth and allow it
to dry in the shade.
6) Check carefully for damage to painted
surfaces. If there is any damage,
“touch-up” the damage following the
procedure below:
1. Clean all damaged spots and allow
them to dry.
2. Stir the paint and “touch-up” the
damaged spots lightly using a small
brush.
3. Allow the paint to dry completely.
Waxing
60B211S
After washing the vehicle, waxing and pol-
ishing are recommended to further protect
and beautify the paint.
Only use waxes and polishes of good
quality.
When using waxes and polishes,
observe the precautions specified by the
manufacturers.
NOTICE
When using a commercial car wash
product, observe the cautions speci-
fied by the manufacturer. Never use
strong household detergents or
soaps.
NOTICE
If you use an automatic car wash,
make sure that your vehicle’s body
parts, such as spoilers, cannot be
damaged. If you are in doubt, consult
the car wash operator for advice.
EXAMPLE

11-4
SPECIFICATIONS
53MH0-74E
*1: When tire replacement is necessary and if the specified load index and speed rated tire is not available, then use a tire of higher load
index and speed rating.ITEM: Wheels and Tires
ALTO 800 ALTO K10
Tire size, front and rear145/80R12 74S*1 155/65 R13 73S*1
145/80R12 74H*1 155/65 R13 73T*1
145/80R12 74T*1 —
Rim size145/80R12 74S*1: 12 × 3.50B 155/65 R13 73S*1 : 13X4 1/2J
145/80R12 74H*1: 12 × 3.50B 155/65 R13 73T*1 : 13X4 1/2J
145/80R12 74T*1: 12 × 3.50B —
Tire pressuresFor the specified tire pressure, see the Tire Information Label located the driver’s door
lock pillar.
ITEM: Capacities (approx.)
ALTO 800 ALTO K10
Coolant (including reservoir tank) 3.5 L
4.5 L
Fuel tank 35 L35 L
Engine oil 3.0 L (replacement with oil filter)2.8 L (replacement with oil filter)
Transaxle oil 1.5 L
1.45 L