2013 SUZUKI ALTO steering

7-4
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
BRAKE
1. Brake fluid (Level, Leakage) I I I R I R I R I R
2.Brake pedal (Pedal-to-wall clearance) IIIIIIIIII
3.Parking brake lever and cable (Play, Damage) IIIIIIIIII
4.a. Brake discs and pads (Wear) – I IIIIIIII
b. Brake drums & shoes (Wear) – – IIIIIIII
5.Master cylinder, wheel cylinder, caliper piston (Fluid leakage, Boot/Seal
Damage)IIIIIIIIII
6.Brake hoses and pipes (Fluid leakage, Damage)
IIIIIIIIII
WHEEL
1. Tyres (Air pressure, Abnormal wear, Crack, Rotation) I
I&OI&O I&OI&OI&OI&OI&OI&O I&O
2. Wheels (Damage) I
I I I I I I I I I
3. Front/Rear wheel bearings (Loose, Damage) –
I I I I I I I I I
FRONT AND REAR SUSPENSION
1. Suspension strut (Oil leakage, Damage) I
I I I I I I I I I
2. Suspension arms/knuckle support (Loose, Damage) –
IIIIII I I I
3. Rear spring (Damage) –
I I I I I I I I I
4. Shock absorbers (Oil leakage, Damage) I
I I I I I I I I I
5. All bolts and nuts (Loose)–
T T T T T T T T T
6. Suspension arms and Tension rods –
I I I I I I I I I
STEERING
1. Steering wheel (Play, Loose) I
I I I I I I I I I
2. All rods and arms (Loose, Damage, Wear) I
I I I I I I I I I
ELECTRICAL
1. Battery electrolyte (Level, leakage) I
I I I I I I I I I
2. Wiring harness connection (Loose, Damage) –
I I I I I I I I I
3. Lighting system (Operation, Stains, Damage) I
I I I I I I I I I
4. Horn (Operation) I
I I I I I I I I I
5. System voltage I
I I I I I I I I I
BODY
1. All chassis bolts and nuts (Tighten)
–II T
T T T T T T
2. All latches, hinges and locks (Function)
II&LI&L I&L
I&L I&L I&L I&L I&L I&L

7-8
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
3. Parking brake level and cable (Play, Damage)IIIIIIIIII
4.a. Brake discs and pads (Wear) – I I IIIIIII
b. Brake drums & shoes (Wear) ––IIIIIIII
5.Master cylinder, wheel cylinder, caliper piston (Fluid leakage, Boot/Seal
Damage)IIIIIIIIII
6.Brake hoses and pipes (Fluid leakage, Damage)
IIIIIIIIII
WHEEL
1. Tyres (Air pressure, Abnormal wear, Crack and Rotation) I
I&OI&O I&OI&OI&OI&OI&OI&O I&O
2. Wheels (Damage) I
I I I I I I I I I
3. Front/Rear wheel bearing (Loose, Damage) –
I I I I I I I I I
FRONT AND REAR SUSPENSION
1. Suspension strut (Oil leakage, Damage) I
I I I I I I I I I
2. Suspension arms/knuckle support (Loose, Damage) –
IIIIII I I I
3. Rear spring (Damage) –
I I I I I I I I I
4. Shock absorbers (Oil leakage, Damage) I
I I I I I I I I I
5. All bolts and nuts (Loose)–
T T T T T T T T T
6. Suspension arms and Tension rods –
I I I I I I I I I
STEERING
1. Steering wheel (Play, Loose) I
I I I I I I I I I
2. All rods and arms (Loose, Damage, Wear) I
I I I I I I I I I
ELECTRICAL
1. Battery electrolyte (Level, Leakage) I
I I I I I I I I I
2. Wiring harness connection (Loose, Damage) –
I I I I I I I I I
3. Lighting system (Operation, Stains, Damage) I
I I I I I I I I I
4. Horn (Operation) I
I I I I I I I I I
5. System voltage I
I I I I I I I I I
BODY
1. All chassis bolts and nuts (Tighten)
–ITT
T T T T T T
2. All latches, hinges and locks (Function)
II&LI&L I&L
I&L I&L I&L I&L I&L I&L
ROAD TEST
1. Operation of Brakes, Gear shifting and speedometer
II I I
I I I I I I
2.Body and Chassis noise
II I I
I I I I I I

7-10
INSPECTION AND MAINTENANCE
53MH0-74E
Drive Belt
Make sure the drive belt tension is correct.
If the belt is too loose, insufficient battery
charging, engine overheating, poor power
steering, poor air conditioning, or exces-
sive belt wear can result. When you press
the belt with your thumb midway between
the pulleys, there should be a deflection
according to the following chart.
The belts should also be examined to
ensure that they are not damaged.
If you need to replace or adjust the belt
have it done by your MARUTI SUZUKI
dealer.F8D
51KM036
K10B
53M-09-003
Engine Oil and Filter
Specified Oil (ALTO 800)
53M-09-004
(1) Preferred
Be sure that the engine oil you use comes
under the quality classification of SG+, SL,
SM and SN. Select the appropriate oil vis-
cosity according to the above chart.
SAE 5W-30 (1) is the best choice for good
fuel economy, and good starting in cold
weather.
Specified Oil
(ALTO K10)
53M-09-005
(1) Preferred
Be sure that the engine oil you use comes
under the quality classification of SL, SM
and SN. Select the appropriate oil viscosity
according to the above chart.
WA R N I N G
When the engine is running, keep
hands, hair, clothing, tools, etc. away
from the moving fan and drive belts.
: 100 N (10 kg, 22 lbs) press
GE: Generator
DEF: Deflection
AC: Air conditioner compressorDEF: 6 – 7 mm
(0.24 – 0.28 in.)
GE
AC
DEF: 7 – 8 mm
(0.28 – 0.31 in.)
EXAMPLE
EXAMPLE

7-20
INSPECTION AND MAINTENANCE
53MH0-74E
Steering
53M-09-032
Steering wheel play “c”:
0 – 30 mm (0.0 – 1.2 in.)
Check the play of the steering wheel by
gently turning it from left to right and mea-
suring the distance that it moves before
you feel slight resistance. The play should
be between the specified values.
Check that the steering wheel turns easily
and smoothly without rattling by turning it
all the way to the right and to the left while
driving very slowly in an open area. If the
amount of free play is outside the specifi-
cation or you find anything else to be
wrong, an inspection must be performed
by your MARUTI SUZUKI dealer.
Tires
53M-09-033
The front and rear tire pressure specifica-
tions for your vehicle are listed on the Tire
Information Label. Both the front and rear
tires should have the specified tire pres-
sure.
Tire Inspection
Inspect your vehicle’s tires at least once a
month by performing the following checks:
1) Measure the air pressure with a tire
gauge. Adjust the pressure if neces-
sary. Remember to check the spare
tire, too.
53M-09-034
EXAMPLEEXAMPLE
WA R N I N G
• Air pressures should be checked
when the tires are cold or you may
get inaccurate readings.
• Check the inflation pressure from
time to time while inflating the tire
gradually, until the specified pres-
sure is obtained.
• Never underinflate or overinflate
the tires.
Underinflation can cause unusual
handling characteristics or can
cause the rim to slip on the tire
bead, resulting in an accident or
damage to the tire or rim.
Overinflation can cause the tire to
burst, resulting in personal injury.
Overinflation can also cause
unusual handling characteristics
which may result in an accident.
EXAMPLE

7-21
INSPECTION AND MAINTENANCE
53MH0-74E
(1) Tread wear indicator
(2) Indicator location mark
2) Check that the depth of the tread
groove is more than 1.6 mm (0.06 in.).
To help you check this, the tires have
molded-in tread wear indicators in the
grooves. When the indicators appear
on the tread surface, the remaining
depth of the tread is 1.6 mm (0.06 in.)
or less and the tire should be replaced.
3) Check for abnormal wear, cracks and
damage. Any tires with cracks or other
damage should be replaced. If any tires
show abnormal wear, have them
inspected by your MARUTI SUZUKI
dealer.
4) Check for loose wheel nuts.
5) Check that there are no nails, stones or
other objects sticking into the tires.Tire Rotation
53M-09-035
To avoid uneven wear of your tires and to
prolong their life, rotate the tires as illus-
trated. Tires should be rotated as men-
tioned in periodic maintenance schedule.
After rotation, adjust front and rear tire
pressures to the specification listed on
your vehicle’s Tire Information Label.
Wheel Balancing
If the vehicle vibrates abnormally on
smooth road, have the wheel balanced at
Maruti Suzuki Authorized Workshop.
Wheel Alignment
In case of abnormal tire wear or pulling
towards one side, have the wheel aligned
at Maruti Suzuki Authorized Workshop
.
CAUTION
Hitting curbs and running over rocks
can damage tires and affect wheel
alignment. Be sure to have tires and
wheel alignment checked periodi-
cally by your MARUTI SUZUKI dealer.
WA R N I N G
• Your MARUTI SUZUKI is equipped
with tires which are all the same
type and size. This is important to
ensure proper steering and han-
dling of the vehicle. Never mix tires
of different size or type on the four
wheels of your vehicle. The size
and type of tires used should be
only those approved by MARUTI
SUZUKI as standard or optional
equipment for your vehicle.
• Replacing the wheels and tires
equipped on your vehicle with cer-
tain combinations of aftermarket
wheels and tires can significantly
change the steering and handling
characteristics of your vehicle.
• Therefore, use only those wheel
and tire combinations approved by
MARUTI SUZUKI as standard or
optional equipment for your vehi-
cle.
NOTICE
Replacing the original tires with tires
of a different size may result in false
speedometer or odometer readings.
Check with your SUZUKI dealer
before purchasing replacement tires
that differ in size from the original
tires.

7-26
INSPECTION AND MAINTENANCE
53MH0-74E
ALTO K10
53M-09-044
53M-09-045
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) – Blank
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) – Blank
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
SECONDARY FUSE
(1) 10A IG2 SIG
(2) 15A Wiper
(3) – Blank
(4) 7.5AAutomated Manual Tran-
saxle 2 (if equipped)
(5) 30A Blower motor
(6) 10A Stop light
(7) 10A Tail light
(8) 15A Audio
(9) 20A Door lock
(10) – Blank
(11) 15A Accessory
(12) – Blank
(13) 30A Power window
(14) 15A Ignition switch
(15) 10A Turn signal light
(16) 10A Meter
(17) 7.5A Air bag
(18) 7.5A IG1 SIG
(19) – Blank
(20) – Blank
(21) 30A Power steering
(22) 30A ST SIG
(23) 15A Horn/Hazard
WA R N I N G
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period
of time, you may have a major electri-
cal problem. Have your vehicle
inspected immediately by your
MARUTI SUZUKI dealer.
EXAMPLE

8-6
EMERGENCY SERVICE
53MH0-74E
Towing
If you need to have your vehicle towed,
contact a professional service. Your dealer
can provide you with detailed towing
instructions.
2-Wheel Drive (2WD) Manual Transaxle
or Automated Manual Transaxle
Manual transaxle vehicles or Automated
Manual Transaxle may be towed using
either of the following methods.
1) From the front, with the front wheels
lifted and the rear wheels on the
ground. Before towing, make sure that
the parking brake is released.
2) From the rear, with the rear wheels
lifted and the front wheels on the
ground, provided the steering and
drivetrain are in operational condition.
Before towing, make sure that transaxle
is in neutral, the steering wheel is
unlocked (the ignition key should be in
the “ACC” position), and the steering
wheel is secured with a clamping
device designed for towing service.
If the Starter Does Not
Operate
1) Try turning the ignition switch to the
“START” position with the headlights
turned on to determine the battery con-
dition. If the headlights go excessively
dim or go off, it usually means that
either the battery is flat or the battery
terminal contact is poor. Recharge the
battery or correct battery terminal con-
tact as necessary.
2) If the headlights remain bright, check
the fuses. If the reason for failure of the
starter is not obvious, there may be a
major electrical problem. Have the vehi-
cle inspected by your authorized MAR-
UTI SUZUKI dealer.
If the Engine is Flooded
If the engine is flooded with gasoline, it
may be hard to start. If this happens, press
the accelerator pedal all the way to the
floor and hold it there while cranking the
engine. (Do not operate the starter motor
for more than 15 seconds).
NOTICE
To help avoid damage to your vehicle
during towing, proper equipment and
towing procedures must be used.
NOTICE
After shifting the auto gear shift gear-
shift lever to the “N” position, always
check the gear position indicator in
the instrument cluster shows the “N”
position to make sure that the
transaxle is disengaged.
If the transaxle cannot be put in neu-
tral, turn the key from the “OFF” to
the “ON” position, and move the auto
gear shift gearshift lever from “N” to
“D”, “M” or “R”, then back to “N”
again. Then turn the key from the
“ON” to the “OFF” position.
These procedures may help put the
transaxle in neutral. If the transaxle
still cannot be put in neutral, you can-
not tow the vehicle without using a
towing dolly.
NOTICE
The steering column is not strong
enough to withstand shocks trans-
mitted from the front wheels during
towing. Always unlock the steering
wheel before towing.