2013 SUZUKI ALTO maintenance

7-4
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
BRAKE
1. Brake fluid (Level, Leakage) I I I R I R I R I R
2.Brake pedal (Pedal-to-wall clearance) IIIIIIIIII
3.Parking brake lever and cable (Play, Damage) IIIIIIIIII
4.a. Brake discs and pads (Wear) – I IIIIIIII
b. Brake drums & shoes (Wear) – – IIIIIIII
5.Master cylinder, wheel cylinder, caliper piston (Fluid leakage, Boot/Seal
Damage)IIIIIIIIII
6.Brake hoses and pipes (Fluid leakage, Damage)
IIIIIIIIII
WHEEL
1. Tyres (Air pressure, Abnormal wear, Crack, Rotation) I
I&OI&O I&OI&OI&OI&OI&OI&O I&O
2. Wheels (Damage) I
I I I I I I I I I
3. Front/Rear wheel bearings (Loose, Damage) –
I I I I I I I I I
FRONT AND REAR SUSPENSION
1. Suspension strut (Oil leakage, Damage) I
I I I I I I I I I
2. Suspension arms/knuckle support (Loose, Damage) –
IIIIII I I I
3. Rear spring (Damage) –
I I I I I I I I I
4. Shock absorbers (Oil leakage, Damage) I
I I I I I I I I I
5. All bolts and nuts (Loose)–
T T T T T T T T T
6. Suspension arms and Tension rods –
I I I I I I I I I
STEERING
1. Steering wheel (Play, Loose) I
I I I I I I I I I
2. All rods and arms (Loose, Damage, Wear) I
I I I I I I I I I
ELECTRICAL
1. Battery electrolyte (Level, leakage) I
I I I I I I I I I
2. Wiring harness connection (Loose, Damage) –
I I I I I I I I I
3. Lighting system (Operation, Stains, Damage) I
I I I I I I I I I
4. Horn (Operation) I
I I I I I I I I I
5. System voltage I
I I I I I I I I I
BODY
1. All chassis bolts and nuts (Tighten)
–II T
T T T T T T
2. All latches, hinges and locks (Function)
II&LI&L I&L
I&L I&L I&L I&L I&L I&L

7-5
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ROAD TEST
1. Operation of Brakes, Gear shifting and speedometer
II I I
I I I I I I
2.Body and Chassis noise
II I I
I I I I I I
AIR CONDITIONER (if equipped)
1. Check belt tension
IIII
IIIIII
3. Tighten compressor mounting bolts
–TTT
TTTTTT
2. All hose joints (Check, Tighten)
IIII
I I I I I I
4. Check functioning of Recirculating flap
IIII
I II I I I
5.Clean condenser with low pressure water
–CCCCCCCCC
6. Check belt for frayed edges, change if necessary
–I I I
I II I I I
7.Check all mounting bolts
–I I I
I I I I I I

7-6
INSPECTION AND MAINTENANCE
53MH0-74E
Periodic Maintenance
Schedule
ALTO K10
“A”: Adjust
“C”: Clean
“R”: Replace or Change
“I” : Inspect, clean, adjust, lubricate or
replace as necessary
“L” : Lubricate
“T” : Tighten to Specified Torque
“O”: Rotate
NOTE:
This table includes services as scheduled
up to 80,000 km mileage. Beyond 80,000
km, carry out the same services at the
same intervals respectively.

7-7
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ENGINE
1.Water pump drive belt (Tension, Wear) ––––– I ––– I
2. Engine Coolant (Level, Leakage) I I I R I R I R I R
3. Engine oil and Oil filter – – RRRRRRRR
4. Cooling system hoses and connections (Leakage, Damage)IIIIIIIIII
5. Engine bolts (All cylinder head and manifold fixings) – – T – T – T – T –
6. Engine Mounting (Loose, Damage) – – T – T – T – T –
7.Valve Clearance –––– I –– I ––
8. Exhaust System (Noise, Leakage etc.) – I – I – I – I – I
9. Positive crankcase ventilation System (Hoses, Connections and Valve) – I – I – I – I – I
IGNITION
1. Ignition wiring (Damage, Deterioration) – – – I – I – I – I
2.Spark plugs –––––R–––R
FUEL
1. Air cleanerPaved-road Clean every 5,000 km. Replace after every 40,000 km.
Dusty condition Clean every 2,500 km or as required. Replace after every 40,000 km.
More frequent replacement if dust condition is severe.
2. Fuel tank cap, fuel lines and connections (Leakage, Damage) – I – – – I – – – I
3. Fuel filter (Leakage) – I I I I R I I I R
CLUTCH AND TRANMISSION
1.Clutch pedal (Play) IIIIIIIIII
2.Clutch slipping (Dragging or Excessive damage) IIIIIIIIII
3. Manual Transmission Oil (Level, Leakage)IIIIIIIIII
Replace every 1,60,000 kms or 10 years whichever comes first
DRIVE SHAFTS
1. Drive shaft boots (Boot cut / Damage)IIIIIIIIII
2.Drive Shaft Noise IIIIIIIIII
BRAKE
1. Brake fluid (Level, Leakage) I I I R I R I R I R
2. Brake pedal (Pedal-to-wall clearance)IIIIIIIIII

7-8
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
3. Parking brake level and cable (Play, Damage)IIIIIIIIII
4.a. Brake discs and pads (Wear) – I I IIIIIII
b. Brake drums & shoes (Wear) ––IIIIIIII
5.Master cylinder, wheel cylinder, caliper piston (Fluid leakage, Boot/Seal
Damage)IIIIIIIIII
6.Brake hoses and pipes (Fluid leakage, Damage)
IIIIIIIIII
WHEEL
1. Tyres (Air pressure, Abnormal wear, Crack and Rotation) I
I&OI&O I&OI&OI&OI&OI&OI&O I&O
2. Wheels (Damage) I
I I I I I I I I I
3. Front/Rear wheel bearing (Loose, Damage) –
I I I I I I I I I
FRONT AND REAR SUSPENSION
1. Suspension strut (Oil leakage, Damage) I
I I I I I I I I I
2. Suspension arms/knuckle support (Loose, Damage) –
IIIIII I I I
3. Rear spring (Damage) –
I I I I I I I I I
4. Shock absorbers (Oil leakage, Damage) I
I I I I I I I I I
5. All bolts and nuts (Loose)–
T T T T T T T T T
6. Suspension arms and Tension rods –
I I I I I I I I I
STEERING
1. Steering wheel (Play, Loose) I
I I I I I I I I I
2. All rods and arms (Loose, Damage, Wear) I
I I I I I I I I I
ELECTRICAL
1. Battery electrolyte (Level, Leakage) I
I I I I I I I I I
2. Wiring harness connection (Loose, Damage) –
I I I I I I I I I
3. Lighting system (Operation, Stains, Damage) I
I I I I I I I I I
4. Horn (Operation) I
I I I I I I I I I
5. System voltage I
I I I I I I I I I
BODY
1. All chassis bolts and nuts (Tighten)
–ITT
T T T T T T
2. All latches, hinges and locks (Function)
II&LI&L I&L
I&L I&L I&L I&L I&L I&L
ROAD TEST
1. Operation of Brakes, Gear shifting and speedometer
II I I
I I I I I I
2.Body and Chassis noise
II I I
I I I I I I

7-9
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
AIR CONDITIONER (if equipped)
1. Check belt tension
IIII
IIIIII
3. Tighten compressor mounting bolts
–TTT
TTTTTT
2. Check all hose joints (Check, Tighten)
IIII
I I I I I I
4. Check functioning of Recirculating flap
IIII
I I I I I I
5.Clean condenser with low pressure water
–CCCCCCCCC
6. Check belt for frayed edges, change if necessary
–I I I
I I I I I I
7.Check all mounting bolts
–I I I
I I I I I I

7-10
INSPECTION AND MAINTENANCE
53MH0-74E
Drive Belt
Make sure the drive belt tension is correct.
If the belt is too loose, insufficient battery
charging, engine overheating, poor power
steering, poor air conditioning, or exces-
sive belt wear can result. When you press
the belt with your thumb midway between
the pulleys, there should be a deflection
according to the following chart.
The belts should also be examined to
ensure that they are not damaged.
If you need to replace or adjust the belt
have it done by your MARUTI SUZUKI
dealer.F8D
51KM036
K10B
53M-09-003
Engine Oil and Filter
Specified Oil (ALTO 800)
53M-09-004
(1) Preferred
Be sure that the engine oil you use comes
under the quality classification of SG+, SL,
SM and SN. Select the appropriate oil vis-
cosity according to the above chart.
SAE 5W-30 (1) is the best choice for good
fuel economy, and good starting in cold
weather.
Specified Oil
(ALTO K10)
53M-09-005
(1) Preferred
Be sure that the engine oil you use comes
under the quality classification of SL, SM
and SN. Select the appropriate oil viscosity
according to the above chart.
WA R N I N G
When the engine is running, keep
hands, hair, clothing, tools, etc. away
from the moving fan and drive belts.
: 100 N (10 kg, 22 lbs) press
GE: Generator
DEF: Deflection
AC: Air conditioner compressorDEF: 6 – 7 mm
(0.24 – 0.28 in.)
GE
AC
DEF: 7 – 8 mm
(0.28 – 0.31 in.)
EXAMPLE
EXAMPLE

7-11
INSPECTION AND MAINTENANCE
53MH0-74E
SAE 0W-20 (1) is the best choice for good
fuel economy, and good starting in cold
weather.
Oil Level Check
68KH066
It is important to keep the engine oil at the
correct level for proper lubrication of your
vehicle’s engine. Check the oil level with
the vehicle on a level surface. The oil level
indication may be inaccurate if the vehicle
is on a slope. The oil level should be
checked either before starting the engine
or at least 5 minutes after stopping the
engine.
Pull out the oil dipstick, wipe oil off with a
clean cloth, insert the dipstick all the way
into the engine, then remove it again. The
oil on the stick should be between the
upper and lower limits shown on the stick.
If the oil level indication is near the lowerlimit, add enough oil to raise the level to the
upper limit.
Refilling
53M-09-007
Remove the oil filler cap and pour oil slowly
through the filler hole to bring the oil level
to the upper limit on the dipstick. Be careful
not to overfill. Too much oil is almost as
bad as too little oil. After refilling, start the
engine and allow it to idle for about a min-
ute. Stop the engine, wait about 5 minutes
and check the oil level again.
Changing Engine Oil and Filter
Drain the engine oil while the engine is still
warm.
1) Remove the oil filler cap.
2) Place a drain pan under the drain plug.
3) Using a wrench, remove the drain plug
and drain out the engine oil.
ALTO 800
53MH0701
Tightening torque for drain plug (1):
49 Nm (4.9 kg-m, 36.0 lb-ft)
EXAMPLE
NOTICE
Failure to check the oil level regularly
could lead to serious engine trouble
due to insufficient oil.
EXAMPLE
CAUTION
The engine oil temperature may be
high enough to burn your fingers
when the drain plug is loosened. Wait
until the drain plug is cool enough to
touch with your bare hands.
(1)EXAMPLE