2013 SUZUKI ALTO battery

3-4
OPERATING YOUR VEHICLE
53MH0-74E
It locks the ignition, and prevents normal
use of the steering wheel after the key is
removed.
To release the steering lock, insert the key
and turn it clockwise to one of the other
positions. If you have trouble turning the
key to unlock the steering, try turning the
steering wheel slightly to the right or left
while turning the key.
ACC
Accessories such as the radio can oper-
ate, but the engine is off.
ON
This is the normal operating position. All
electrical systems are on.
START
This is the position for starting the engine
using the starter motor. The key should be
released from this position as soon as the
engine starts.
Ignition key reminder (if equipped)
A buzzer sounds intermittently to remind
you to remove the ignition key if it is in the
ignition switch when the driver’s door is
opened.
81A297S
WA R N I N G
• Never remove the ignition key
while the vehicle is moving. The
steering wheel will lock and you
will not be able to steer the vehicle.
• Always remove the ignition key
when leaving the vehicle even if
only for a short time. Also do not
leave children alone in a parked
vehicle. Unattended children could
cause accidental movement of the
vehicle or could tamper with power
windows. They also could suffer
from heat stroke in warm or hot
weather. These could result in
severe injury or even death.
EXAMPLENOTICE
• Do not use the starter motor for
more than 15 seconds at a time. If
the engine does not start, wait 15
seconds before trying again. If the
engine does not start after several
attempts, check the fuel and igni-
tion systems or consult your MAR-
UTI SUZUKI dealer.
• Do not leave the ignition switch in
the “ON” position if the engine is
not running as the battery will dis-
charge.

INSPECTION AND MAINTENANCE
7
53MH0-74E
INSPECTION AND MAINTENANCE
Maintenance Schedule ....................................................... 7-2
Periodic Maintenance Schedule ........................................ 7-2
Drive Belt ............................................................................. 7-10
Engine Oil and Filter ........................................................... 7-10
Engine Coolant .................................................................... 7-13
Air Cleaner ........................................................................... 7-15
Spark Plugs ......................................................................... 7-15
Gear Oil ................................................................................ 7-16
Clutch Pedal ........................................................................ 7-17
Fuel Filter ............................................................................. 7-17
Brakes .................................................................................. 7-18
Steering ................................................................................ 7-20
Tires ...................................................................................... 7-20
Battery .................................................................................. 7-22
Fuses .................................................................................... 7-23
Bulb Replacement ............................................................... 7-27
Wiper Blades ....................................................................... 7-29
Windshield Washer Fluid ................................................... 7-31
Air Conditioning System .................................................... 7-31

7-1
INSPECTION AND MAINTENANCE
53MH0-74E
60A187S
WA R N I N G
You should take extreme care when
working on your vehicle to prevent
accidental injury. Here are a few pre-
cautions that you should be espe-
cially careful to observe:
(Continued)
WA R N I N G
(Continued)
• To prevent damage or unintended
activation of the air bag system or
seat belt pretensioner system, be
sure the battery is disconnected
and the ignition switch has been in
the “LOCK” position for at least 90
seconds before performing any
electrical service work on your
vehicle. Do not touch air bag sys-
tem components, seat belt preten-
sioner system components or
wires.
The wires are wrapped with yellow
tape or yellow tubing, and the cou-
plers are yellow for easy identifica-
tion.
• Do not leave the engine running in
garages or other confined areas.
• When the engine is running, keep
hands, clothing, tools, and other
objects away from the fan and drive
belt. Even though the fan may not
be moving, it can automatically
turn on without warning.
(Continued)
WA R N I N G
(Continued)
• When it is necessary to do service
work with the engine running, make
sure that the parking brake is set
fully and the transaxle is in Neutral.
• Do not touch ignition wires or other
ignition system parts when start-
ing the engine or when the engine
is running, or you could receive an
electric shock.
• Be careful not to touch a hot
engine, exhaust manifold and
pipes, muffler, radiator and water
hoses.
• Do not allow smoking, sparks, or
flames around fuel or the battery.
Flammable fumes are present.
• Do not get under your vehicle if it is
supported only with the portable
jack provided in your vehicle.
• Be careful not to cause accidental
short circuits between the positive
and negative battery terminals.
• Keep used oil, coolant, and other
fluids away from children and pets.
Dispose of used fluids properly;
never pour them on the ground,
into sewers, etc.

7-4
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
BRAKE
1. Brake fluid (Level, Leakage) I I I R I R I R I R
2.Brake pedal (Pedal-to-wall clearance) IIIIIIIIII
3.Parking brake lever and cable (Play, Damage) IIIIIIIIII
4.a. Brake discs and pads (Wear) – I IIIIIIII
b. Brake drums & shoes (Wear) – – IIIIIIII
5.Master cylinder, wheel cylinder, caliper piston (Fluid leakage, Boot/Seal
Damage)IIIIIIIIII
6.Brake hoses and pipes (Fluid leakage, Damage)
IIIIIIIIII
WHEEL
1. Tyres (Air pressure, Abnormal wear, Crack, Rotation) I
I&OI&O I&OI&OI&OI&OI&OI&O I&O
2. Wheels (Damage) I
I I I I I I I I I
3. Front/Rear wheel bearings (Loose, Damage) –
I I I I I I I I I
FRONT AND REAR SUSPENSION
1. Suspension strut (Oil leakage, Damage) I
I I I I I I I I I
2. Suspension arms/knuckle support (Loose, Damage) –
IIIIII I I I
3. Rear spring (Damage) –
I I I I I I I I I
4. Shock absorbers (Oil leakage, Damage) I
I I I I I I I I I
5. All bolts and nuts (Loose)–
T T T T T T T T T
6. Suspension arms and Tension rods –
I I I I I I I I I
STEERING
1. Steering wheel (Play, Loose) I
I I I I I I I I I
2. All rods and arms (Loose, Damage, Wear) I
I I I I I I I I I
ELECTRICAL
1. Battery electrolyte (Level, leakage) I
I I I I I I I I I
2. Wiring harness connection (Loose, Damage) –
I I I I I I I I I
3. Lighting system (Operation, Stains, Damage) I
I I I I I I I I I
4. Horn (Operation) I
I I I I I I I I I
5. System voltage I
I I I I I I I I I
BODY
1. All chassis bolts and nuts (Tighten)
–II T
T T T T T T
2. All latches, hinges and locks (Function)
II&LI&L I&L
I&L I&L I&L I&L I&L I&L

7-8
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
3. Parking brake level and cable (Play, Damage)IIIIIIIIII
4.a. Brake discs and pads (Wear) – I I IIIIIII
b. Brake drums & shoes (Wear) ––IIIIIIII
5.Master cylinder, wheel cylinder, caliper piston (Fluid leakage, Boot/Seal
Damage)IIIIIIIIII
6.Brake hoses and pipes (Fluid leakage, Damage)
IIIIIIIIII
WHEEL
1. Tyres (Air pressure, Abnormal wear, Crack and Rotation) I
I&OI&O I&OI&OI&OI&OI&OI&O I&O
2. Wheels (Damage) I
I I I I I I I I I
3. Front/Rear wheel bearing (Loose, Damage) –
I I I I I I I I I
FRONT AND REAR SUSPENSION
1. Suspension strut (Oil leakage, Damage) I
I I I I I I I I I
2. Suspension arms/knuckle support (Loose, Damage) –
IIIIII I I I
3. Rear spring (Damage) –
I I I I I I I I I
4. Shock absorbers (Oil leakage, Damage) I
I I I I I I I I I
5. All bolts and nuts (Loose)–
T T T T T T T T T
6. Suspension arms and Tension rods –
I I I I I I I I I
STEERING
1. Steering wheel (Play, Loose) I
I I I I I I I I I
2. All rods and arms (Loose, Damage, Wear) I
I I I I I I I I I
ELECTRICAL
1. Battery electrolyte (Level, Leakage) I
I I I I I I I I I
2. Wiring harness connection (Loose, Damage) –
I I I I I I I I I
3. Lighting system (Operation, Stains, Damage) I
I I I I I I I I I
4. Horn (Operation) I
I I I I I I I I I
5. System voltage I
I I I I I I I I I
BODY
1. All chassis bolts and nuts (Tighten)
–ITT
T T T T T T
2. All latches, hinges and locks (Function)
II&LI&L I&L
I&L I&L I&L I&L I&L I&L
ROAD TEST
1. Operation of Brakes, Gear shifting and speedometer
II I I
I I I I I I
2.Body and Chassis noise
II I I
I I I I I I

7-10
INSPECTION AND MAINTENANCE
53MH0-74E
Drive Belt
Make sure the drive belt tension is correct.
If the belt is too loose, insufficient battery
charging, engine overheating, poor power
steering, poor air conditioning, or exces-
sive belt wear can result. When you press
the belt with your thumb midway between
the pulleys, there should be a deflection
according to the following chart.
The belts should also be examined to
ensure that they are not damaged.
If you need to replace or adjust the belt
have it done by your MARUTI SUZUKI
dealer.F8D
51KM036
K10B
53M-09-003
Engine Oil and Filter
Specified Oil (ALTO 800)
53M-09-004
(1) Preferred
Be sure that the engine oil you use comes
under the quality classification of SG+, SL,
SM and SN. Select the appropriate oil vis-
cosity according to the above chart.
SAE 5W-30 (1) is the best choice for good
fuel economy, and good starting in cold
weather.
Specified Oil
(ALTO K10)
53M-09-005
(1) Preferred
Be sure that the engine oil you use comes
under the quality classification of SL, SM
and SN. Select the appropriate oil viscosity
according to the above chart.
WA R N I N G
When the engine is running, keep
hands, hair, clothing, tools, etc. away
from the moving fan and drive belts.
: 100 N (10 kg, 22 lbs) press
GE: Generator
DEF: Deflection
AC: Air conditioner compressorDEF: 6 – 7 mm
(0.24 – 0.28 in.)
GE
AC
DEF: 7 – 8 mm
(0.28 – 0.31 in.)
EXAMPLE
EXAMPLE

7-22
INSPECTION AND MAINTENANCE
53MH0-74E
Tubeless Tires (If equipped)
The vehicle is equipped with Tubeless
Tires. In tubeless tire, a thin layer of butyl
rubber is used for lining the inside of the
tubeless tire. This layer is to prevent air
loss and fulfilling the purpose of tube. The
air pressure is maintained by the sealing
between tire bead and wheel rim. Tubeless
tires are having advantage of slow air loss
and preventing sudden deflation while driv-
ing.
Care and maintenance tips for tubeless
tires
1) Always maintain recommended inflation
pressure. Driving continuously at low
inflation pressure can lead to tire dam-
age.
2) In case any leakage is found, check for
any nail penetration/valve core dam-
age or rim bent. Damaged wheel must
not be used.
3) In case tire has run at low pressure, it
must be inspected for any defect.
4) Whenever new tire is fitted, replace the
valve.
5) If continuous high speed driving is
required, increase tires pressure by
5 psi over recommended inflation pres-
sure.
6) Never run the tire beyond TWI (Tread
Wear Indicator). The tire is recom-
mended to be replaced when the
remaining tread has worn to this point.
The indicators are spaced across thetread around the tire marked by a trian-
gular symbol (TWI).
7) Always prefer tubeless tire mounting
machine. In case of manual mounting-
tire/wheel rim damage may occur.
8) In case of any problem, please get in
touch with Maruti Suzuki Authorized
Workshop.Battery
WA R N I N G
• Batteries produce flammable
hydrogen gas. Keep flames and
sparks away from the battery or an
explosion may occur. Never smoke
when working in the vicinity of the
battery.
• When checking or servicing the
battery, disconnect the negative
cable. Be careful not to cause a
short circuit by allowing metal
objects to contact the battery posts
and the vehicle at the same time.
• To avoid harm to yourself or dam-
age to your vehicle or battery, fol-
low the jump starting instructions
in the “EMERGENCY SERVICE”
section of this manual if it is neces-
sary to jump start your vehicle.
• Diluted sulfuric acid spilled from
battery can cause blindness or
severe burns. Use proper eye pro-
tection and gloves. Flush eyes or
body with ample water and get
medical care immediately if suf-
fered.
• Keep batteries out of the reach of
children.

7-23
INSPECTION AND MAINTENANCE
53MH0-74E
53m-09-036
The level of the battery solution must be
kept between the “MAX” and the “MIN”
level lines at all times. If the level is found
to be below the “MIN” level line, add dis-
tilled water to bring level between “MAX”
and “MIN”. You should, however, periodi-
cally check the battery, battery terminals,
and battery holddown bracket for corro-
sion. Remove corrosion using a stiff brush
and ammonia mixed with water, or baking
soda mixed with water. After removing cor-
rosion, rinse with clean water.
If your vehicle is not going to be driven for
a month or longer, disconnect the cable
from the negative terminal of the battery to
help prevent discharge.Replacement of the battery53M-09-037
To remove the battery:
1) Disconnect the negative cable (1).
2) Disconnect the positive cable (2).
3) Remove the retainer bolts (3) and
remove the retainer (4).
4) Remove the battery along with cover
assembly (5) (if equipped).To install the battery:
1) Install the battery in the reverse order of
removal.
2) Tighten the retainer nuts and battery
cables securely.
NOTE:
When the battery is disconnected, some of
the vehicle’s function will be initialized and/
or deactivated.
These function are required to reset after
the battery is reconnected.
Fuses
Your vehicle has three types of fuses, as
described below:
Main fuse
The main fuse takes current directly from
the battery.
Primary fuses
These fuses are between the main fuse
and individual fuses, and are for electrical
load groups.
Individual fuses
These fuses are for individual electrical cir-
cuits. To remove a fuse, use the fuse puller
provided in the fuse box.
CAUTION
Do not overfill the battery with dis-
tilled water in order to avoid spillage.
EXAMPLE
NOTICE
• Ensure that battery should not be
removed without cover assembly.
• When the battery is reassembled
into the vehicle, kindly ensure that
battery cover is also installed along
with battery.
EXAMPLE