2013 SSANGYONG KORANDO light

8310-00
1. LAMP SPECIFICATIONS
1) Exterior Lamps
2) Interior Lamps
Description Numbers Specification
Front room lamp 2 10W
Glove box lamp 1 5W
Center room lamp 1 10W
Luggage lamp 1 10W
Door courtesy lamp 2 5W
Description Numbers Specification
Headlamp High beam 2 H1-55W
Low beam 2 H7-55W
Turn signal lamp 2 P21W
Position lamp - LED
Front fog light 2 H16-19W
Rear fog light 2 21W
Side repeater - LED
Rear combination lamp Tail lamp - LED
Turn signal lamp 2 PY21W
Back-up lamp 2 W16W
Stop lamp 2 P21W
License plate lamp 2 W5W
High mounted stop lamp - LED
Puddle lamp 2 LED

Luminous intensity is a measure for the amount of light which passes through the unit area per
time unit. The SI unit of luminous intensity is the candela (cd), an SI base unit. -Luminous Intensity
Luminance describes the amount of light that passes through or is emitted from a particular area,
and falls within a given solid angle. It is measured in sb or nt. -Luminance
This indicates the amount of light reaching a given area. Measuring unit is lux (lx) and it is not
directly proportional to the brightness of the area as the reflection rate is not included. -Intensity of illumination
The LED stands for "Light Emitting Diode" or "Luminescent Diode." LED is a semiconductor diode
that emits incoherent narrow-spectrum light when electrically biased in the forward direction of the
p-n junction, as in the common LED circuit. In short, it is an element that converts electric signals
into light signals. Yellow, blue, red and white LEDs are currently available.
The followings are the advantages of LED.
It is not glaring and doesn't have short circuit unlike the conventional lamps.
It is semi-permanent and doesn't generate heat.
Its power consumption is much lower than those of conventional bulbs. -
-
Pin No. Specification
Operating voltage 9 V to 16 V
Load Max. 200 mA (relay load)
Operating temperature
Storage temperature
Mounting location Top center of inner side of windshield glass
2. AUTOMATIC LIGHT SENSOR SPECIFICATIONS

Rear side
Rear combination lamp
- Rear combination lamp design and its function changed
- Tail lamp (stop lamp) changed to LED type
Backup lamp
Turn signal
lamp
Stop/tail lamp
Rear fog
light
Tail lamp
Stop lamp,
Rear fog
light (EU)
Turn signal
lamp
Backup lamp
Stop lamp

8310-00
Rear combination lamp
Rear side
License plate lampReflex reflector lamp
High mounted stop lamp
Vehicle with spoilerVehicle without spoiler
Tail lamp
Stop lamp,
Rear fog
light (EU)Turn signal
lamp
Backup lamp
Stop lamp

3) Operating Process
(1) Headlamp (high/low beam) operation process
The headlamp is usually operated by the multifunction switch or by the REKES or smart key through the
BCM.
The BCM controls the headlamp and tail lamp according to the signal from the AUTO light sensor
through LIN communication when the multifunction switch is in "AUTO" position.
Headlamp - low beam
Headlamp - high beam
DRL (Day Time Running Light)
DRL is the function to turn on the high beam and tail lamp without any intervention from the light
switch. DRL turns off the lamps when turning off the light switch. This is an additional safety device to
prevent the accident.

(3) Auto light (LIN)
The auto light sensor unit is installed to the back side of the ECM mirror located upper center of the
windshield, and detects the illuminance change. The BCM communicates with the auto light sensor
when the ignition is turned on, and turns on or off the tail lamp and headlamp automatically according to
the signals from the sensor when the multifunction switch is set to AUTO light.
The BCM communicates with the rain sensor even if the multifunction switch is in tail lamp.
Auto light switch Automatic light sensor unit

8310-00
Control by BCM
The rain sensor & AUTO light module communicates with BCM with IGN ON. When the AUTO light
switch is in the AUTO position, the BCM controls the tail lamp and headlamp according to the LIN
communication data.

(4) License lamp operation process
When the corresponding lamp comes on and
goes off by operating the tail lamp, AUTO light,
high beam and low beam on the multifunction
switch, the license lamp also does.