2013 SMART FORTWO COUPE tailgate

Carry out the following steps within
30 seconds:
X If the value of the charg ecurrent is not
set to 8 A: set the value to 8 Aand confirm.
X Set the value of the charge current to
10 A and confirm.
X Set the value of the charge current to
8 A and confirm.
X Set the value of the charge current to
10 A and confirm.
X Press the encryption button on the
powerline adapter withi nthree minutes.
When the powerline adapter shows a
connection, the connection process was
successful.
i Observe the separate operating
instructions of the powerline adapter.
i Contact an authorized electric drive
smart center if you have any questions.
X Next, set the value of the charge current
to the desired value once again.
As soon as the vehicle establishes an
Internet connection, you can also use the
"Vehicle Homepage" at home during the
charging process. Changes you have made
via the "Vehicle Homepage" are adopted
after the charging process is complete.
This data transmission ends after
approximately three days. Charging at an AC power socket or a
private wallbox
Charging cable G
WARNING
The drive system is under high voltage.
Only use the charging cable that is
supplied with the vehicle or a wallbox
charging cable . Only use these charging
cables to charge the vehicle. Do not extend
a charging cable. Do not use a charging
cable if it is damaged. You could otherwise suffer an electric
shock and be seriously or even fatally
injured.
When charging at a private wallbox or
public charging station (level 2charging),
the charging cable is non-detachably
connected to the wallbox or charging
station.
Storing the charging cable You can store the charging cable in the
vehicle.
R
cabrio:
-in a box which is available as a
separate accessory (part number A 451
810 00 80).
- in the storage compartment in the
tailgate, if available (Y page 104).
In this case, you can not stow the roof
bars of the roof system there.
R coupé: in the storage compartment in the
tailgate, if available (Y page 104). Storage compartment in the tailgate
X
Hold charging cable connector 0003in your
left hand and power supply connector 0002
in your right hand.
X Lay spiral section 002Bof the cable into
the rear area of the storage compartment.
X Place the remainder of the charging
cable into the recesses in the storage
compartment as shown in the
illustration. 112
High-voltage battery>> Operation.

Display messages Possible causes/consequences and
0001 Solutions
0001
Drive System
0001Switch Engine Off There is a malfunction in the drive train. If the drive system
continues to run, the drive train can become damaged.
In addition, the red 0001warning lamp in the instrument
cluster lights up and a warning signal sounds.
X Switch off the drive system.
X Do not continue driving.
X Contact an authorized electric drive smart center. 0007
Do Not Tow
(Away) Either the drive or the high‑voltage system is faulty.
In addition, the
0002warning lamp in the instrument cluster
lights up.
X It is recommended to have the vehicle transported by a
qualified specialist workshop.
Do not tow the vehicle on its own wheels. 0007
Charging Not
Possible There is a malfunction in the on-board charger. The
high‑voltage battery cannot be charged.
X
Contact an authorized electric drive smart center. 0007
Parking Lock
Inactive The gear selector lever is in position
P, but the parking lock
is not detected.
In addition, a warning signal sounds.
X Apply the parking brake.
X Move the gear selector lever to another position, e.g. to R.
X Move the gear selector lever to Pagain. 0001
Driver´s Door Ajar The driver’s door is open.
X
Close the driver’s door. 0002
Door Ajar The passenger door is open.
X
Close the passenger door. 0003
Tailgate Open A tailgate or the rear soft top
9
is open.
X Close the tailgates or the rear soft. 0003
Charge Cable
Connected The charging cable is inserted in the vehicle power socket.
The vehicle cannot be moved.
In addition, a warning signal sounds.
X
To drive off, remove the charging cable from the vehicle
power socket and stow the cable in the vehicle. 9
cabriolet only. Display messages
157>> Practical hints. Z

The arrow on bulb socket
0002must be in
line with the line on the headlamp
housing.
X Turn bulb socket 0002clockwise by a
quarter of turn.
Side turn signal lamp bulb X
Removing: Open the door on the
corresponding side. X
Press on retaining lug 0002in the
direction of the arrow until the side turn
signal lamp housing disengages.
X Close the door.
X Use a suitable tool to loosen the side turn
signal lamp housing from the fender.
X Turn the bulb socket counterclockwise
and pull it out of the side turn signal
lamp housing.
X Pull the bulb out of the bulb socket.
X Installing: Insert the new bulb into the
bulb socket.
X Insert the bulb socket into the side turn
signal lamp housing and turn the bulb
socket clockwise.
X Fit the side turn signal lamp housing
onto the fender.
X Press gently onto the side turn signal
lamp housing.
The side turn signal lamp housing must
audibly engage. Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
X Turn exterior lamp switch to position
0004 (Ypage 62).
X Switch off the ignition.
Tail lamp unit X
Removing:
Coupé: Open the upper tailgate.
X Open the lower tailgate.
X Cabriolet: Open the rear soft top
(Y page 70).
X Remove the side cover in the cargo
compartment on the corresponding side.
X Fold the damping material forward, if
necessary. Left bulb carrier illustrated as example
0002
Retaining tab
0003 Electrical connector
X Press retaining tab 0002in the center of
the bulb carrier upwards.
X Pull the bulb carrier out of the tail lamp
housing. 176
Replacing bulbs>> Practical hints.