2013 SKODA YETI lights

Turn signal and main beamFig. 26
Operating lever: Turn signal and
main beam operation
First read and observe the introductory information and safety warn-
ings on page 47.
Operating lever positions » Fig. 26 .
Switch on right 
turn signal
Switch on left 
turn signal
Switch on main beam 
(spring-tensioned position)
Switch on main beam or headlamp flasher (spring-loaded position) 
The parking light can also be controlled with the control lever » page 53.
Main beam
The main beam can only be switched on when the low beam lights are on.
When the high beam or headlight flasher is on, the warning light 
illuminates in
the instrument cluster.
Flashing
When the left or right turn signal is on, the warning light 
or 
flashes in the
instrument cluster.
The flashing light is turned on even before the upper and lower pressure point.
This is advantageous in certain driving manoeuvres. For example, when changing
lanes hold the control lever of each pressure point.
The turn signal light switches itself off automatically when driving around a curve
or after making a turn.
The indicator light flashes at twice its normal rate if a bulb for the turn signal light fails.
ABCD“Convenience turn signal”
If you only wish to flash three times, briefly push the lever to the upper or lower
pressure point and release again.
The “Lane ch. flash” can be activated or deactivated via the Maxi DOT display in
the Lane ch. flash » page 29, Settings menu item.WARNINGOnly turn on the main beam or the headlight flasher if other road users will
not be dazzled.
Note
The headlight flasher system can also be operated if the ignition is switched off.
Automatic driving lamp control
Fig. 27
Light switch: AUTO position
First read and observe the introductory information and safety warn- ings on page 47.
If the light switch is in position 
» Fig. 27 , the parking lights, low beam and
number plate lights are switched on or off automatically.
The light is regulated based on data gathered by the sensor fitted in the holder of
the rear-view mirror below the windscreen.
If the light switch is in position 
, the symbol 
lights up next to the light
switch. If the light is switched on automatically, the symbol 
next to the light
switch also lights up. 
49Lights and visibility

Automatic driving light control during rain
The daytime running lights are switched on automatically if the following condi-
tions are met:
The light switch is in the position  » Fig. 27 .
Automatic wiping during rain or wiping in position 2 or 3 ( » page 57) Is
switched on for more than 15 seconds.
The light is turned off if wiping is not switched on for longer than about 4 mi- nutes.
CAUTION
Do not stick any stickers or similar objects in front of the light sensor on the windscreen, so as not to cancel the function of automatic driving light control or
to impair its effectiveness.
Adaptive headlights (AFS)
First read and observe the introductory information and safety warn-ings
on page 47.
The AFS system makes sure the street remains lit up depending on the traffic and weather situation.
The system automatically adjusts the cone of light in front of the vehicle to the driving speed or the use of the wiper.
The AFS system works in tandem with automatic driving lamp control 
, there-
fore please also read the following » page 49.
The AFS system can only work if the following condition is met. The light switch is in the position 
.
The AHL system operates in the following modes.
Out of town mode
The cone of light in front of the vehicle is similar to the low beam. The mode is
active if none of the following modes are active.
City mode
The light cone in front of the vehicle is adjusted so that this also illuminates the
adjacent side-walks, intersections, pedestrian crossings, etc. The mode is active at speeds of 15-50 km/h.
Motorway mode
The cone of light in front of the vehicle is adjusted so that the driver can respond in time to an obstruction or other hazard in time. The mode is active at speeds
above 120 km/h.
Rain mode
The cone of light in front of the vehicle is adjusted so that the driver can reduce the glare from oncoming vehicles in rain.
The mode is active at speeds of 20 – 70 km/h and if the windscreen wipers con-tinuously operate for a period of time longer than 2 minutes. The mode is deacti-
vated when the windscreen wipers are switched off for longer than 8 minutes.
Dynamic cornering lights
The cone of light in front of the vehicle is adjusted to the steering angle so that the road in the curve is illuminated. This function is active at speeds greater than
10 km.h and in all AFS modes.
Tourist lights (Travel mode)
This mode makes it possible to drive in countries with opposing traffic system
(driving on the left/right) without dazzling the oncoming vehicles.
When this mode is active, the above-mentioned modes and the side swivel of the
headlights is deactivated.
This mode can be enabled or disabled via the Maxi DOT display in the Travel
mode » page 29 menu option.WARNINGIf the AFS system is defective, the headlights are automatically lowered to the
emergency position, which prevents a possible dazzling of oncoming traffic. This reduces the cone of light in front of the vehicle. Drive carefully and visit aspecialist garage as soon as possible.
Note
When the “Tourist light” mode is active, the warning icon 
flashes for about 10
seconds each time the ignition is switched on.
50Using the system

Fog lightsFig. 28
Light switch: Switch on the front
fog lamp
First read and observe the introductory information and safety warn-
ings on page 47.
Switching on/off
›
Turn the light switch to position 
or 
» Fig. 28 .
›
Pull the light switch to position
1
.
The rear fog light is switched off in the reverse order.
The indicator light 
lights up in the instrument cluster when the fog lights are
switched on » page 14.

Fog lights with the CORNER function
First read and observe the introductory information and safety warn-ings
on page 47.
The CORNER function improves illumination of the vehicle surroundings when
turning, parking and the like, by switching on the fog lights on the respective side
of the vehicle.
The CORNER function is switched on automatically if the following conditions
are met.
The turn signal is switched on or the front wheels are turned sharply to the
right or left 1)
.
The engine is running.
The vehicle is stopped or moves at a speed of no more than 40 km/h.
The low beam is switched on or the light switch is in the position  and the
low beam is switched on.
The daytime running lights are not switched on. The fog lights are not switched on.
Note
The two fog lights are switched on when you shift into the reverse gear.
Rear fog light
First read and observe the introductory information and safety warn-
ings
on page 47.
Switching on/off
›
Turn the light switch to position 
or 
» Fig. 28 on page 51.
›
Pull the light switch to position
2
.
The rear fog light is switched off in the reverse order.
The warning light 
lights up in the instrument cluster when the rear fog light is
switched on » page 14.
Only the rear fog light on the trailer lights up if the vehicle has a factory-fitted
towing device or a towing device from ŠKODA original accessories and it is driven
with a trailer.

COMING HOME / LEAVING HOME
First read and observe the introductory information and safety warn-ings
on page 47.
COMING HOME/LEAVING HOME (hereafter referred to only as function) switches on the lights for a short time after leaving the vehicle or when approaching the
vehicle. 


1)
If both switch-on conditions are conflicting, for example, if the front wheels are turned to the left and
the right turn signal light is switched on, the turn signal light has the higher priority.
51Lights and visibility

The daytime running lights are switched on automatically if the following condi-tions are met:
The light switch is in the position  » Fig. 27 on page 49.
The visibility in the vehicle environment is reduced. The ignition is switched off.
The parking aid is activated.
The function switches on the following light, depending on the equipment fit- ted.
› Parking lights
› Low beam
› Entry lighting in the exterior mirrors
› Licence plate light
The light is controlled on the basis of information that is collected from the holder
mounted in the rear-view mirror sensor » page 49 .
COMING HOME
The light turns on automatically when you open the driver's door on (within 60
seconds of turning off the ignition).
The light turns off 10 seconds after closing all the doors and the boot lid or after
the pre-set time has expired.
If a door or the boot lid remains open, the light goes out after 60 seconds.
LEAVING HOME
The light turns on automatically after the vehicle is unlocked with the remote
control.
The light turns off after 10 seconds or after a pre-set time or after the vehicle is
locked.
If no door is opened, the vehicle is locked automatically after 30 seconds.
Activate/deactivate the function
The functions and settings of the illumination time can be activated/deactivated via the MAXI DOT display in the menu items Coming Home or Leaving
Home » page 29 .
CAUTION
■
Do not attach any stickers or similar objects in front of the light sensor on the
windscreen to avoid impairing the function or its reliability.■
If this function is activated constantly, the battery will be heavily discharged
particularly in short-haul traffic.
Hazard warning light systemFig. 29
Button for hazard warning light
system
First read and observe the introductory information and safety warn-
ings on page 47.
Switching on/off
›
Press the button 
» Fig. 29 .
All the turn signal lights on the vehicle flash at the same time when the hazard
warning light system is switched on. The warning light for the turn signals and
the warning light in the button also flash at the same time. The hazard warning
light system can also be operated if the ignition is switched off.
If one of the airbags is deployed, the hazard warning light system will switch on
automatically.
If the turn signal light is switched on when the hazard warning light and the igni- tion are both switched on, then only the turn signal light on the corresponding
vehicle side will flash.
WARNINGSwitch on the hazard warning light system if, for example, the following oc-
curs.■
You encounter a traffic congestion.
■
The vehicle has broken down.

52Using the system

Parking lightsFirst read and observe the introductory information and safety warn-ings
on page 47.
Parking light  switching on
›
Switching off the ignition.
›
Place the control lever into position
A
or
B
as far as it can go » Fig. 26 on
page 49 - the parking light on the right/left-hand side of the vehicle is switched on.
The parking light  can only be activated if the ignition is switched off.
If the right or left turn signal light has been switched on and the ignition is switched off, the parking light is not automatically switched on.
Switching on the side light on both sides 
›
Turn the light switch
A
to position 
» Fig. 25 on page 47 and lock the vehicle.
After pulling out the ignition key and opening the driver's door, an audible warn-
ing sounds. After a few seconds or after closing the driver's door, the audible
alarm is turned off, but the parking lights will remain switched on.

Instrument lighting
Fig. 30
Controls for the instrument
lighting
First read and observe the introductory information and safety warn-
ings on page 47.
The brightness of the instrument lights can be set only if the parking, low beam or high beam is switched on.
Knob » Fig. 30 .
Adjust brightness of the instrument lighting.
NoteOn vehicles with MAXI DOT display » page 28 the brightness of the instrument
lighting is set automatically. A manual brightness adjustment can therefore only
have a limited effect.
Interior lights
 Introduction
This chapter contains information on the following subjects:
Front interior light
53
Rear interior light
54
Front door warning light
54
Front interior light
Fig. 31
Operation of the front interior light: Version 1/version 2
First read and observe the introductory information given on page 53.
Rocker switch positions » Fig. 31 .
switching on
switching off
Operation using the door contact switch (middle position) 
53Lights and visibility

For vehicles with interior monitoring, there is no icon for the center position (op-
eration with the door contact switch).
Switch for reading lights .
Switching left reading lamp on/off
Switching right reading lamp on/off
If light operation with the door contact switch is enabled, the light will come on
when one of the following events occurs:
› The vehicle is unlocked.
› One of the doors or the luggage compartment lid is being opened.
› The ignition key is removed.
If light operation with the door contact switch is enabled, the light will go off
when one of the following events occurs:
› The vehicle is locked.
› The ignition is switched on.
› About 30 seconds after all the doors have been closed.
Note
If the interior light remains switched on when the ignition is switched off or if one
of the doors is open, the light will automatically go out after around 10 minutes.
Rear interior light
Fig. 32
Interior lights at the rear
First read and observe the introductory information given on page 53.
The light can be operated by moving the lens into one of the following posi-
tions » Fig. 32 .
switch on
switch off
Operation using the door contact switch (middle position) 1)

Front door warning light
Fig. 33
Front door warning light
First read and observe the introductory information given on page 53.
The warning light
» Fig. 33 turns on when the front door is opened.
The warning light » Fig. 33 turns off when the front door is closed.
In vehicles without a warning light only a reflector is installed at this point.
Note
If the door is open and the ignition switched off, the light will extinguish auto-
matically after around 10 minutes.

1)
In this position, apply the same rules to the rear interior light as for the front interior light » page 53,
Front interior light .
54Using the system

Visibility
Introduction
This chapter contains information on the following subjects:
Windscreen and rear window heater
55
Sun visors
55
Windscreen and rear window heater
Fig. 34
Buttons for the rear and front window heating system: manual air
conditioning / Climatronic
First read and observe the introductory information given on page 55.
Explanation of graphic.Switch the rear window heater on/off
Switching the windscreen heater on/off
When heating is switched on, a lamp within the button lights up
The windscreen and rear window heater only operates when the engine is run-
ning.
The windscreen and rear window heater automatically switches off after approxi-
mately 10 minutes.
For the sake of the environmentThe heating should be switched off as soon as the window is de-iced or free from
mist. The reduced current consumption will have a favourable effect on fuel econ-
omy » page 133 , Saving electrical energy .
Note
■
If the on-board voltage drops, the windscreen and rear window heater switches
off automatically, to provide sufficient electrical energy for the engine con-
trol » page 210 , Automatic load deactivation .■
If the light is flashing inside the button, the heater is off due to low battery.
■
The position and shape of the switch may vary according to the equipment fit-
ted.

Sun visors
Fig. 35
Sun visor/double sun visor
First read and observe the introductory information given on page 55.
The sun visor for the driver or front passenger can be pulled out of the fixture and
swivelled towards the door in the direction of the arrow
1
» Fig. 35 .
The vanity mirrors in the sun visors are provided with covers. Push the cover in
the direction of the arrow
2
.
The purpose of the strap
A
is to store small, light objects, such as a notepad, etc.
On vehicles that are equipped with a double sun visor, the auxiliary visor can be
unfolded in the direction of the arrow
3
after swivelling the sun visor towards
the door. 
55Lights and visibility

■Keep the wiper blades clean. They may become soiled, e.g., with wax residues
after washing in automatic car wash systems » page 188.■
The windscreen washer nozzles for the windscreen are heated when the en-
gine is running and the outside temperature is less than approx. +10 °C.

Windscreen wipers and washers
Fig. 36
Operating lever: Windscreen
wipers and washer settings
First read and observe the introductory information and safety warn-
ings on page 56.
Operating lever positions » Fig. 36 .
 Wipers off
 Periodic windscreen wiping/automatic wiping in rain
 slow windscreen wiping
 rapid windscreen wiping
 
Flick windscreen wiping (spring-tensioned position)
 Automatic wipe/wash for windscreen (spring-tensioned position)
 Wiping the rear window pane (the windscreen wiper wipes at regular in-
tervals after a few seconds)
 Automatic wipe/wash for the rear window (spring-tensioned position)
 Switches for setting the required break between the individual wiper
strokes (
1
periodic windscreen wiping) or the wiper speed in rain (
1
auto-
matic windscreen wiping in rain)
Automatic wipe/wash for windscreen 
The wash system operates immediately, the windscreen wipers wipe somewhat later. The wash system and the windscreen wiper operate simultaneously at a
speed of more than 120 km/h.
01234567ALetting go of the lever will cause the windscreen wash system to stop and the
wiper to continue for another 3-4 wiper strokes (depending on the period of
spraying of the windscreen).
At a speed of more than 2 km/h, the wiper wipes once again 5 seconds after the
last wiper stroke in order to wipe the last drops from the windscreen. This func-
tion can be activated/deactivated by a specialist garage.
Automatic wipe/wash for the rear window 
The wash system operates immediately, the windscreen wiper wipes somewhat
later.
Letting go of the operating lever will cause the windscreen wash system to stop and the wiper to continue for another 2-3 wiper strokes (depending on the spray-
ing duration). The operating lever remains in position 6
» Fig. 36 .
Automatic rear window wiping
If the lever is in position
2
or
3
» Fig. 36 , the rear window is wiped every
30 or 10 seconds if the vehicle's speed exceeds 5 km/h.
If automatic windscreen wiping in rain is activated (the operating lever is in the
position
1
) the function is only active if the windscreen wipers operate in contin-
uous mode (no break between each wiping process).
Automatic rear window wiping can be activated/deactivated via the MAXI DOT
display in the menu item Rear wiper » page 29 .
Winter setting of the windscreen wiper If the windscreen wipers are in rest position, they cannot be folded out from thewindscreen. For this reason we recommend adjusting the windscreen wipers in
winter so that they can be folded out from the windscreen easily.
› Switch on the windscreen wipers.
› Switch off the ignition.
The windscreen wipers remain in the position in which they were when switching
off the ignition.
The service position can also be used as a winter position » page 235.
Note
If the slow or the fast wiper setting is switched on and the vehicle speed decrea-
ses to below 4 km/h, the wiper speed is incrementally set to a lower wiper speed.
The original setting is restored step by step when the speed of the vehicle ex-
ceeds 8 km/h.
57Lights and visibility