2013 Seat Ibiza ST technical specifications

239
If and when
Note
In the vehicle, there are more fuses than those indicated in this chapter.
These should only be changed by a specialised workshop. 
Replacing a blown fuse
Fig. 154 Image of a
blown fuse
Preparation
● Switch off the ignition, lights and all electrical equipment.
● Open the corresponding fuse box ⇒ page 238.
Identifying a blown fuse
A fuse is blown if its metal strip is ruptured ⇒ Fig. 154.
Point a lamp at the fuse. This will make it easier to see if the fuse is blown. To replace a fuse
●
Remove the fuse.
● Replace the blown fuse by one with an identical amperage rating (same
colour and markings) and identical size ⇒ 
.
● Replace the cover again or close the fuse box lid.
CAUTION
If you replace a fuse with higher-rating fuse, you could cause damage to an-
other part of the electrical system. 
Bulb change General notes
Before changing any bulb, first turn off the failed component.
Do not touch the glass part of the bulb with your bare hands. The finger-
prints left on the glass will vaporise as a result of the heat generated by the
bulb, causing a reduction in bulb life and condensation on the mirror sur-
face, thus reducing effectiveness.
A bulb must only be replaced by one of the same type. The type is indicated
on the bulb, either on the glass part or on the base.
Below, the light source used for all functions is broken down.
Double headlights - H7 Long Life
- H7
- W5W Long Life - PY 21W 
Dipped beam
Main beam
Position
Turn signal
Safety FirstOperating instructionsPractical TipsTechnical Specifications

241
If and when
Single headlight bulb change
Single headlight bulb
Fig. 155 Single head-
light
Side lights - Dipped beam/main beam.
Turn signal. 
A
B
Turn signal bulb
Fig. 156 Single turn sig-
nal lamp
– Raise the bonnet.
– Turn bulb holder ⇒ Fig. 156 A
to the left and pull.
– Remove the bulb by pressing on the bulb holder and rotating at
the same time to the left.
– Installation involves all of the above steps in reverse sequence. 
Safety FirstOperating instructionsPractical TipsTechnical Specifications

243
If and when
– Move the loop ⇒ Fig. 157 1
in the direction of the arrow and
remove the cover.
– Remove the bulb holder 4
⇒ Fig. 159 outwards.
– Replace the bulb by pulling it out and inserting the replace-
ment.
– Installation is done in the reverse order. 
Double headlight bulb change Double headlight
Fig. 160 Double head-
lights
Side lights
Main beam headlights
A
B
Dipped beam headlights
Turn signal lights

Side light
Fig. 161 Side lights
Fig. 162 Side lights 
C
D
Safety FirstOperating instructionsPractical TipsTechnical Specifications

245
If and when
Dipped beam headlights
Fig. 165 Dipped beam
headlights
Fig. 166 Dipped beam
headlights
– Raise the bonnet.
– Move the loop ⇒ Fig. 165 1
in the direction of the arrow and
remove the cover. –
Remove connector ⇒ Fig. 166 2
from the bulb.
– Unclip the retainer spring ⇒ Fig. 166 3
pressing inwards to the
right.
– Extract the bulb and fit the replacement so that the rim of the
attachment plate is on the reflector cut-out.
– Fit the connector.
– Fit the cover and close the strap. Make sure that the gasket sits
well on the casing cover during the operation.
– Check whether the new bulb is working. 
Turn signal lights
Fig. 167 Turn signal
– Raise the bonnet.
– Turn bulb holder ⇒ Fig. 167 A
to the left and pull. 
Safety FirstOperating instructionsPractical TipsTechnical Specifications

247
If and when
Changing the bulbs of AFS headlights
AFS headlight bulbs
Fig. 168 AFS headlight
bulbs
Turn signal lights
Xenon headlight (dipped beam/main beam) 
Changing the xenon bulb
The procedure for changing the bulb is the same on both sides of the vehi-
cle.
WARNING
This type of bulb should be changed at a specialised workshop.

A
B
Turn signal light bulb
Fig. 169 Turn signal
– Raise the bonnet.
– Turn bulb holder ⇒ Fig. 169 A
to the left and pull.
– Remove the bulb by pressing on the bulb holder and rotating at
the same time to the left.
– Installation involves all of the above steps in reverse sequence. 
Safety FirstOperating instructionsPractical TipsTechnical Specifications

249
If and when
Note
Due to the difficulty of accessing fog light bulbs, have them replaced at a
Technical Service or specialised workshop. 
Remove the bulb holder
Fig. 173 Front fog light
– Remove connector ⇒ 
Fig. 173 A
from the bulb.
– Turn bulb holder ⇒ 
Fig. 173 B
to the left and pull.
– Remove the bulb by pressing on the bulb holder and turning it
anticlockwise at the same time.
– Installation involves all of the above steps in reverse sequence.
– Check that the bulb works properly. Changing rear bulbs
Applies to the model: IBIZA / IBIZA SC
Summary of LED tail lights
LEDS
● Brake lights
● Side lights
Bulbs
● Rear fog light
● Reversing light
● Turn signal 
Safety FirstOperating instructionsPractical TipsTechnical Specifications

251
If and when
Applies to the model: IBIZA / IBIZA SC
Changing bulbs on tail lights
Fig. 177 Changing bulbs
on tail lights
Fig. 178 Changing bulbs
on tail lights
– Remove the connector from housing A
⇒ Fig. 176.–
Remove the bulb holder, separating it from the casing. To do
this, press tabs B
in the direction of the arrows
⇒ Fig. 177.
– When the bulb holder has been removed, press in the direction
of the arrow 1
and at the same time, turn in the direction of
the arrow 2 ⇒ Fig. 178
Changing bulbs. LED lamps
Carry out the same operations as in lights fitted with bulbs.
If necessary, remove the socket, as if it were a bulb.
If the brake light and/or side light with LEDs have to be replaced, the tail
light must be replaced. 
Changing the rear lights (on the wing) Applies to the model: IBIZA STOverview of tail lights
Tail lights on side panel Bulb lamps
● Brake lights
● Side light
● Turn signal
Tail lights on side panel LED lamps
● Brake lights (LEDS)
● Side lights (LEDS)
● Turn signal 
Safety FirstOperating instructionsPractical TipsTechnical Specifications

253
If and when
Changing the rear lights (on the rear lid)
Applies to the model: IBIZA ST Overview of tail lights
Lights on the rear lid Bulb lamps
● Reverse lights
● Side light
● Fog lights
Lights on the rear lid LED lamps
● Reverse lights
● Side lights (LEDS)
● Fog lights Applies to the model: IBIZA ST
Accessing the rear lid lights
Fig. 181 Lights on the
rear lid
– Open the rear lid.
– On the rear lid lining there is a lid behind each light.
– Remove the lid with a flat screwdriver, placing it in notch A
⇒ Fig. 181. 
Safety FirstOperating instructionsPractical TipsTechnical Specifications