2013 RENAULT KANGOO display

87B-12V1 MR-376-X76-87B000$080.mif
87B
UCH
VDiag No.: 0F
MAIN SCREEN
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Engine
immobiliserET549:Immobiliser activeNOIn the event of a fault, apply
the interpretation of status
ET549.
Blank UCH ET008:Blank UCHNOIn the event of a fault, apply
the scenario SC004 Program
UCH.
SupplyPR001:Battery voltage12 V < X < 12.5 VIn the event of a fault, run
fault finding on the charging
circuit (see Technical Note
6014A, Checking the
charging circuit).
ET004:+ 12V after ignition
feedYESIn the event of a fault, apply
the interpretation of status
ET004.
ET091:Engine runningNOIn the event of a fault,
perform a test on the injection
computer (see 13B, Diesel
injection or 17B, Petrol
injection).
Speed PR008:Vehicle speedX in km/hIn the event of a fault,
perform a test on the vehicle
speed or ABS computer (see
38C, Anti-lock braking
system).
UCH_V0F_CCONF
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check

87B-13V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: ACCESS - SAFETY
SUB-FUNCTION: ACCESS
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Supply ET004:+ 12V after
ignition feedYESIn the event of a fault, apply
the interpretation of status
ET004.
Speed PR008:Vehicle speedX in mph (km/h)In the event of a fault,
perform a test on the vehicle
speed or ABS computer (see
38C, Anti-lock braking
system).
Opening
elementsET489:Front doorsOpen when the front doors
are open.In the event of a fault, apply
the interpretation of status
ET489.
ET551:Rear doors or
luggage
compartmentOpen when rear doors or
luggage compartment are
open.In the event of a fault, apply
the interpretation of status
ET551.

87B-14V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: ACCESS - SAFETY
SUB-FUNCTION: STARTING
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Supply ET004:+ 12V after
ignition feedYESIn the event of a fault,
apply the interpretation of
status ET004.
Opening
elementsET183:Key already
programmed for
the vehicleYESIn the event of a fault,
apply the interpretation of
status ET183 (see 82D,
Access – Security).
ET184:Valid key codeYES when the ignition is
switched onIn the event of a fault,
apply the interpretation of
status ET184 (see 82D,
Access – Security).
Engine
immobiliserET549:Immobiliser
activeNOIn the event of a fault,
apply the interpretation of
status ET549.
Immobiliser
warning lightET127:Immobiliser
warning lightOFFIn the event of a fault,
apply the interpretation of
status ET127.
KeyPR056:Number of keys
allocated1 to 4In the event of a fault,
apply the interpretation of
status PR056 (see 82D,
Access – Security).
ET185:Key code
receivedYES when the ignition is
switched onIn the event of a fault,
apply the interpretation of
status ET185 (see 82D,
Access – Security).

87B-15V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: LIGHTING
SUB-FUNCTION: LIGHTING CONTROL
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Side lights ET484:Side lights signalPresent when the side lights
are illuminated.In the event of a fault, apply
the interpretation of status
ET484 (see 80D, Lighting).
Direction
indicatorsET485:Hazard warning
lights signalPresent when the hazard
warning lights are
illuminated.In the event of a fault, apply
the interpretation of status
ET485 (see 80D, Lighting).
ET486:Right-hand
direction indicator
signalPresent when the right-hand
indicator is controlled.In the event of a fault, apply
the interpretation of status
ET486 (see 80D, Lighting).
ET487:Left-hand
direction indicator
signalPresent when the left-hand
indicator is controlled.In the event of a fault, apply
the interpretation of status
ET487 (see 80D, Lighting).

87B-16V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: WIPING
SUB-FUNCTION: WIPER CONTROL
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Supply ET004:+ 12V after
ignition feedYESIn the event of a fault,
apply the interpretation of
status ET004.
Park positionET027:Windscreen
wiper park
positionActive when the wiper
control is in the intermittent
position each time the
wiper stops.In the event of a fault,
apply the interpretation of
fault ET097 Windscreen
wiper park position (see
85A, Wiping - Washing).
ET097:Rear screen
wiper park
positionActive when the wiper
control is in the intermittent
position each time the
wiper stops.In the event of a fault,
apply the interpretation of
fault DF040 Rear screen
wiper park position (see
85A, Wiping - Washing).
Windscreen wiper
speed settingET558:Windscreen
wiper speed
setting selectionYes when the wiper control
is in the intermittent
position.In the event of a fault,
apply the interpretation of
status ET558 (see 85A,
Wiping - Washing).

87B-17V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: WIPING (CONTINUED)
SUB-FUNCTION: WIPER CONTROL
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Wiping - Washing
signalsET555:Rear screen
wiper signalPresent when the rear
screen wiper is working.In the event of a fault,
apply the interpretation of
status ET555 (see 85A,
Wiping - Washing).
ET492:Windscreen
washer signalPresent when the
windscreen washer is
working.In the event of a fault,
apply the interpretation of
status ET492 (see 85A,
Wiping - Washing).
ET557:Rear screen
washer signalPresent when the rear
screen washer is working.In the event of a fault,
apply the interpretation of
status ET557 (see 85A,
Wiping - Washing).
Supply PR001: Battery voltage12 V < X < 12.5 VIn the event of a fault, run
fault finding on the charging
circuit (see Technical Note
6014A, Checking the
charging circuit).

87B-28
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-376-X76-87B000$130.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of commands87B
UCH
VDiag No.: 0F
Use this command only with a new and blank UCH.
A new UCH has no immobiliser code and is therefore not assigned to the vehicle; once it is fitted on the vehicle, it
must be programmed to assign it to the vehicle.
To carry out this programming, always use a key belonging to the vehicle (allocated to the old UCH).
Before starting this operation, make sure that there are no components capable of interfering with the
electromagnetic field (e.g.: CB (Citizen Band), mobile phone, etc.).
SC004PROGRAMMING THE UCH
Equipment required
CLIP
Note:
After replacing just the UCH, no operation needs to be carried out on the injection and electric power-assisted
steering computers.
The computers keep the same immobiliser code.
IMPORTANT
When the UCH programming procedure is successfully completed, the UCH is no longer blank and is permanently
assigned to the vehicle. It will not work on another vehicle.
IMPORTANT
When the programming operation is complete, only remove the key once the Programming complete message
is displayed on the screen. Otherwise, programming fails and the UCH can no longer be used.
UCH_V0F_SC004

87B-29
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-376-X76-87B000$130.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of commands87B
UCH
VDiag No.: 0F
UCH programming procedure
– Establish dialogue with the UCH.
– Select the Repair mode menu.
– Select the Programming menu.
– Select line SC004 Program UCH.
Follow the instructions on the CLIP diagnostic tool.
In "not connected" mode, when the Clip diagnostic tool displays the programming key, make a note of this key and
the VIN.
To obtain the immobiliser code, see Technical Note 5037A, Code delivery procedure.
Operations to be carried out after programming the UCH
Enter the vehicle's VIN into the computer using command VP004 Enter VIN.
After programming the UCH, allocate all the keys using command SC015 Allocate key.
Configure the equipment that is present or not on the vehicle using command SC008 UCH type.
SC004
CONTINUED
IMPORTANT
Do not interrupt the procedure when it is in progress.
If it is interrupted, restart the procedure in "not connected mode"; a new programming key will be displayed.
IMPORTANT
In "not connected" mode, the programming key can only be used for a limited amount of time, as indicated by the
Clip diagnostic tool.
After this time, the programming key and associated immobiliser code are no longer valid. The operation must be
restarted from the beginning.