2013 RENAULT KANGOO light

80D-17
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-80D000$080.mif
LIGHTING
Fault finding – Interpretation of statuses80D
UCH
Vdiag No.: 0F
ET485HAZARD WARNING LIGHTS SIGNAL
NOTESThere must be no present or stored faults.
Activate the hazard warning lights switch.
The status should be PRESENT.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
"ABSENT"
Check for the presence and condition of supply fuse F31 (10 A) on the passenger
compartment fuse and relay box, component code 260 (see MR 374 Mechanical,
81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the hazard warning lights switch connector,
component code 125.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the operation of the hazard warning lights control.
Check the continuity between the following connections:
•64Q and MK of component 125,
•MK and 64D of component 125.
If the connection or connections are faulty and if there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair)
repair the wiring, otherwise replace it.
Check the continuity of the following connection:
•64D between components 125 and 645.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
UCH_V0F_ET485

80D-18
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-80D000$080.mif
LIGHTING
Fault finding – Interpretation of statuses80D
UCH
Vdiag No.: 0F
ET485
CONTINUEDHAZARD WARNING LIGHTS SIGNAL
"ABSENT"
Check the continuity of the following connection:
•MK of component 125:
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
• Check the insulation, continuity and the absence of interference resistance on
the following connection:
•64Q between components 125 and 645.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, contact the techline.

80D-19
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-80D000$080.mif
LIGHTING
Fault finding – Interpretation of statuses80D
UCH
Vdiag No.: 0F
ET486
ET487RIGHT-HAND INDICATOR SIGNALLEFT-HAND INDICATOR SIGNAL
NOTESThere must be no present or stored faults.
Switch on the ignition.
Activate the left or right direction indicator control.
The status should be PRESENT.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
"ABSENT"
Check for the presence and condition of supply fuse F31 (10 A) on the passenger
compartment fuse and relay box, component code 260 (see MR 374 Mechanical,
81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the direction indicator stalk connector,
component code 209 and the UCH connector, component code 645.
If the connector or connectors are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
Check the operation of the indicator light stalk in the left-hand indicator position:
Check the continuity between connections 64T and NA.
Check the operation of the direction indicator stalk in the right-hand indicator position:
Check the continuity between connections 64S and NA.
Check the continuity of connection NA of component 209.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Disconnect the connectors of the UCH, the right-hand indicator, and the left-hand
indicator.
Check the continuity and insulation of the following connections:
•64S between components 209 and 645,
•64T between components 209 and 645.
If the connection or connections are faulty and if there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair)
repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ET486/UCH_V0F_ET487

80D-20V1 MR-376-X76-80D000$090.mif
80D
UCH
Vdiag No.: 0F
Tool commands Diagnostic tool name Comments
AC022Left-hand direction indicatorThis command is used to activate the left-
hand direction indicators.
AC023Right-hand direction indicatorThis command is used to activate the right-
hand direction indicators.
AC145Front courtesy lightsThis command is used to activate the front
courtesy lights.
LIGHTING
Fault finding – Command summary table

80D-21
AFTER REPAIRCarry out a road test and then a check using the diagnostic tool.
V1 MR-376-X76-80D000$100.mif
80D
UCH
Vdiag No.: 0F
AC022LEFT-HAND INDICATOR
NOTESThis command is used to activate the left-hand direction indicators.
There must be no present or stored faults.
Check the conformity of the left-hand direction indicator bulbs.
Switch on the ignition.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check for the presence and condition of supply fuse F31 (10 A) on the passenger compartment fuse and relay box,
component code 260 (see MR 374 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the indicator control stalk connector, component code 209, and the UCH
connector, component code 645.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the operation of the indicator light stalk in the left-hand indicator position:
Check the continuity between connections 64T and NA of component 209.
Check the continuity of connection NA of component 209.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
UCH_V0F_AC022
LIGHTING
Fault finding – Interpretation of commands

80D-22
AFTER REPAIRCarry out a road test and then a check using the diagnostic tool.
V1 MR-376-X76-80D000$100.mif
LIGHTING
Fault finding – Interpretation of commands80D
UCH
Vdiag No.: 0F
AC022
CONTINUED
Check the continuity and the insulation of the following connections:
•64T between components 209 and 645,
•64C between components 645 and 173,
•64C between components 645 and 256,
•64C between components 645 and 268,
•MB between component 268 and earth,
•MB between component 256 and earth,
•MG between component 173 and earth.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.

80D-23
AFTER REPAIRCarry out a road test and then a check using the diagnostic tool.
V1 MR-376-X76-80D000$100.mif
LIGHTING
Fault finding – Interpretation of commands80D
UCH
Vdiag No.: 0F
AC023RIGHT-HAND DIRECTION INDICATOR
NOTESThis command is used to activate the right-hand direction indicators.
There must be no present or stored faults.
Check the conformity of the right-hand direction indicator bulbs.
Switch on the ignition.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check for the presence and condition of supply fuse F31 (10 A) on the passenger compartment fuse and relay box,
component code 260 (see MR 374 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the indicator control stalk connector, component code 209, and the UCH
connector, component code 645.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the operation of the indicator control stalk in the right-hand indicator position:
Check the continuity between connections 64S and NA of component 209.
Check the continuity of connection NA of component 209.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
UCH_V0F_AC023

80D-24
AFTER REPAIRCarry out a road test and then a check using the diagnostic tool.
V1 MR-376-X76-80D000$100.mif
LIGHTING
Fault finding – Interpretation of commands80D
UCH
Vdiag No.: 0F
AC023
CONTINUED
Check the continuity and the insulation of the following connections:
•64S between components 209 and 645,
•64D between components 645 and 172,
•64D between components 645 and 255,
•64D between components 645 and 267,
•MQ between component 267 and earth,
•MQ between component 255 and earth,
•MF between component 172 and earth,
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the techline.