2013 RENAULT KANGOO ignition

13B-194V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
TEST 8 Injector return flow
NOTESSpecial note:
Certain faults make it impossible to carry out this test - deal with these first.
Does the engine start?
Command AC029 High pressure circuit sealing also checks the return volume of each injector to detect any
leaks around the injectors.
Be careful with any objects (tool or other) on the engine housing during the four cycles of the operation
(possible vibrations).
Tooling required
–Mot. 1711 Injector flow measuring kit.
Or: Use four pipes with internal diameter 4mm and approximately 50 cm in length, and four graduated
measuring cylinders.
Procedure
– Ensure that the engine coolant temperature is above 60°C,
– switch off the ignition,
– disconnect the return pipes from the four injectors,
– cap the pump venturi tube to prevent the low-pressure circuit from depriming,
– connect the four transparent tubes in place of the return pipes,
– put the other ends of the four pipes into four graduated measuring cylinders.
NOA
YES
DCM1.2_V08_TEST08

13B-196V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
TEST 8
CONTINUED 2
At the end of the idling phase and these two cycles, the return volume of each injector must be:
45 ml (maximum)for Euro 4 type engines: K9K 714 - 718 - 740 - 792 - 796.
35 ml (maximum).for the euro 3 type engines: K9K 790 - 794.
If the return volume of one of the injectors is more than the values above, only replace the faulty injector (see
MR388 (Logan/Sandero) or MR451 (Duster), Mechanical, 13B, Diesel injection, Diesel injector: Removal -
Refitting).
Disconnect the 4 transparent pipes and reconnect the injector return circuit.
Carry out the following test to confirm the repair:
– With the ignition off, disconnect the low pressure actuator from the pump (brown IMV connector) and connect
the test adapter (test IMV, Mot. 1711),
– electrically disconnect the 4 injectors,
– switch on the ignition, connect the diagnostic tool and re-establish dialogue with the injection system,
– Go to the Main computer statuses and parameters screen,
– activate the starter for 5 seconds,
– read the maximum rail pressure value PR038 Rail pressure during the test on the diagnostic tool.
If the rail pressure (PR038 Rail pressure) is lower than 1050 bar, run test 6 High pressure system check.
– Switch off the ignition, and reconnect the four injectors electrically,
– disconnect the test filling actuator (test IMV) and reconnect the low pressure actuator connector (IMV) to the
pump,
– switch on the ignition again, and clear the injection faults using the diagnostic tool.
If the rail pressure (PR038) is greater than 1050 bar, the repair is correct.
End of TEST8.

13B-197V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
TEST 8
CONTINUED 3
If the engine does not start, only the static leakage can be measured, i.e. the leakage with the injector closed, not
actuated and under high pressure.
Make sure that the ignition circuit is working correctly (minimum engine speed 200 rpm).
Tooling required
–Mot. 1711 Injector flow measuring kit.
Or: Use 4 pipes with internal diameter 4mm and approximately 50 cm in length, and a test adapter (TEST
IMV).
Procedure
– Switch off the ignition,
– disconnect the return pipes from the four injectors,
– cap the pump venturi tube to prevent the low-pressure circuit from depriming,
– connect the four transparent pipes in place of the return pipes (Mot. 1711),
– disconnect the low pressure actuator from the pump (brown IMV connector) and connect a test IMV or the Mot.
1711,
– electrically disconnect the four injectors,
– switch on the ignition and engage the starter for 5 seconds,
– measure the amount of diesel fuel in each pipe.
If the return leakage is greater than 10 cm, replace the injector(s) (see MR 388 (Logan/Sandero) or MR 451
(Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 13B, Diesel injection, Diesel
injector: Removal - Refitting).
Switch off the ignition, and reconnect the four injectors electrically.
Disconnect the test low pressure actuator and reconnect the low pressure actuator connector to the pump.
Disconnect the four transparent tubes and reconnect the injectors return circuit. Switch on the ignition again, and
clear the injection faults using the diagnostic tool.
A

13B-198V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
TEST 8
CONTINUED 4
Carry out the following test to confirm the repair:
–With the ignition off, disconnect the low pressure actuator from the pump (brown IMV connector) and
connect the test adapter (test IMV, Mot. 1711),
– electrically disconnect the four injectors,
– switch on the ignition, connect the diagnostic tool and re-establish dialogue with the injection system,
– go to the Main computer statuses and parameters screen,
– engage the starter for 5 seconds,
– read the maximum rail pressure value PR038 Rail pressure during the test on the diagnostic tool.
If the rail pressure (PR038 Rail pressure) is lower than 1050 bar, run TEST 6 High pressure system check.
– Switch off the ignition, and reconnect the four injectors electrically,
– disconnect the test IMV and reconnect the low-pressure actuator connector to the pump,
– switch on the ignition again, and clear the injection faults using the diagnostic tool.
End of TEST 8

13B-199V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
TEST 9 Diesel filter check
Check the conformity of the diesel filter.
Is the diesel filter in order?Replace the filter with an original
part (see MR 388 (Logan/Sandero),
MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2) or MR 374 (Kangoo VLL),
Mechanical, 13A, Fuel supply, Fuel
filter: Removal - Refitting).
Switch off the ignition and analyse the diesel fuel in the diesel filter.
– Disconnect the diesel supply and return hoses from the filter.
– Block the filter inlets and outlets straight away with appropriate plugs.
– Remove the filter from its support and shake it well keeping the plugs in place and empty the contents of the
filter into a glass container by lifting up a protective plug and undoing the bleed screw.
Check whether there are black particles present at the bottom of the container.
Pass a magnet beneath the container to collect all the
metal particles.
Take the magnet away from the container.Diesel filter in good order.
Do the particles collected using the magnet cover a surface
area greater than 1 cm
2?
Replace the entire injection
system.Diesel filter in good
order.
NO
YES
YESNO
YESNO
DCM1.2_V08_TEST09