2013 RENAULT KANGOO heater

13B-145V1 MR-376-X76-13B000$130.mif
13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
Tool command Diagnostic tool title Comments
RZ001Fault memoryThis command is used for clearing the computer's stored
faults
RZ002EGR programming adaptivesUse this command when replacing the EGR valve (not
applicable to K9K796 Euro 2).
RZ004Pressure regulation adaptivesUse this command when simultaneously replacing the four
injectors and after replacing/retightening the accelerometer.
It enables you to reset the injector adaptives.
RZ005ProgrammingThis command enables you to reinitialise the entire computer
configuration.
AC001Preheating unitActivating this controls the preheating unit to test the heater
plug supply.
AC002EGR solenoid valveActivating this enables an audible check of the mechanical
operation of the EGR valve (not applicable to K9K796
Euro 2).
AC004Turbocharging solenoid valveActivating this enables an audible check of the operation of
the turbocharging solenoid valve.
AC005Cylinder 1 injectorActivating this enables an audible check of the injector on
cylinder 1.
AC006Cylinder 2 injectorRunning this allows you to you listen to the injector on
cylinder 2 when operating.
AC007Cylinder 3 injectorActivating this enables an audible check of the injector on
cylinder 3.
AC008Cylinder 4 injectorActivating this enables an audible check of the injector on
cylinder 4.
AC010High pressure pumpActivating this lets you listen to the operation of the high-
pressure pump.
AC028Static testActivating this enables fault finding to be run on the EGR,
high pressure pump and water in fuel warning light circuits
DIESEL INJECTION
Fault finding – Command summary table

13B-152
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP2 The engine will not start
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply test 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter
(see MR 388 (Logan/Sandero),
MR 451 (Duster), MR 423 (Thalia
2/Symbol 2) or MR 374 (Kangoo
VLL), Mechanical, 19B, Exhaust,
Catalytic converter: Removal -
Refitting).
Check the electrical circuit by running TEST 2 Electrical circuit check.
Check the electrical conformity of the heater plugs (the resistance of the heater plug must be less than 2 ).
YES
NO
A
DCM1.2_V08_ALP02

13B-155
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP3 The engine starts with difficulty, or starts then stalls
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply test 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR
388 (Logan/Sandero), MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2) or MR 374
(Kangoo VLL), Mechanical, 19B, Exhaust,
Catalytic converter: Removal - Refitting).
Check the electrical conformity of the heater plugs (the resistance of the heater plug must be less than 2 ).
YES
NO
A
DCM1.2_V08_ALP03

13B-161
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP5
CONTINUED
Is the compression in order? Carry out the necessary repairs.
Check the electrical conformity of the heater plugs (the resistance of the heater plug must be less than 2 ).
Check the high pressure system by running test 6 High pressure system check.
Contact the Techline if the customer complaint is still present.
A
NO
YES

13B-180
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP16 Engine rattling, noisy engine, turbocharger noise
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
If the noise is coming from the turbocharger, apply the Technical Note 5164A, Fault finding of noises.
Note:
Pay close attention to faulty components that might result in unjustified replacement of the turbocharger. For
example, whistling does not necessarily indicate damage to the turbocharger (this could be coming from the
exhaust, the timing, the gearbox, etc.).
Check that the fuel tank is correctly filled and that the fuel is correct by running TEST 13 Diesel fuel conformity
check.
Check the levels of engine oil and coolant.
Is the compression in order? Carry out the necessary repairs.
Check the electrical conformity of the heater plugs (the resistance value of the heater plug must be less than
2).
NO
YES
A
DCM1.2_V08_ALP16

13B-182
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP17 Blue, white or black smoke
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Is the compression in order? Carry out the necessary repairs
Check the electrical conformity of the heater plugs (the resistance of the heater plug must be less than 2 ).
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR 388
(Logan/Sandero), MR 451 (Duster), MR 423
(Thalia 2/Symbol 2) or MR 374 (Kangoo VLL),
Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Check the air inlet circuit by running TEST 5 Inlet circuit check.
NO
YES
YES
NO
A
DCM1.2_V08_ALP17

13B-184
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP18 Blue, black or white smoke when accelerating.
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check that the engine has not sucked up its oil (engine racing).
Is the compression in order? Carry out the necessary repairs.
Check the electrical conformity of the heater plugs (the resistance of the heater plug must be less than 2 ).
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR 388
(Logan/Sandero), MR 451 (Duster), MR 423
(Thalia 2/Symbol 2) or MR 374 (Kangoo VLL),
Mechanical, 19B, Exhaust, Catalytic converter:
Removal - Refitting).
Check the air inlet circuit by running TEST 5 Inlet circuit check.
NO
YES
YES
NO
A
DCM1.2_V08_ALP18