2013 RENAULT KANGOO coolant temperature

13B-96
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF121
PRESENT
OR
STOREDACCELEROMETER CIRCUIT
1.DEF: No signal
NOTESPriorities when dealing with a number of faults:
– DF001 Coolant temperature sensor circuit,
– DF002 Air temperature sensor circuit,
– DF003 Atmospheric pressure sensor circuit,
– DF098 Fuel temperature sensor circuit,
A fault on one of these sensors could lead to incorrect fault finding on the
accelerometer.
Conditions for applying the fault finding procedure to a stored fault:
The fault is considered present when the engine is running.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the conformity of the injectorsfitted to the vehicle in relation to the type of vehicle and engine number (low,
high or very high injector pressure).
Check the connection and condition of the accelerometer connector, component code 146.
Check the connection and condition of the injection computer connector, component code 120 and the shielding
of the sensor on connection TB1.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3DQ between components 120 and 146,
●3S between components 120 and 146.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
DCM1.2_V08_DF121

13B-115
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF859
PRESENT
OR
STOREDINJECTOR PROGRAMMING CYCLE NOT DONE
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is considered present when the engine is running.
Priorities when dealing with a number of faults:
– Deal with all the other faults before fault DF859
Special notes:
This fault is activated when the injectors have not been reset for 1800 miles
(3000 km).
Leave the vehicle to run at idle speed until the engine is warm.
When the engine is warm (PR064 COOLANT TEMPERATURE above 77°C), carry out the following test drive:
– Drive at a speed of up to 30 mph (50 km/h) and change into 5th gear.
– Stay in this gear and perform 8 accelerations from 30 mph (50 Km/h) to 54 mph (90 Km/h).
– At the end of driving: without switching off the ignition, allow the vehicle to run at idle speed for at least
10 minutes.
– Switch off the ignition, and wait 30 seconds.
– switch on the ignition, check that the fault is stored and clear the fault.
DCM1.2_V08_DF859

13B-120V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
STATUS CHECK (CONTINUED 1)
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Air
conditioningET116:Climate control
authorisationNO
YES: The UCH should send an
activation request to the injection.
The coolant pressure sensor must
not be defective. Satisfactory engine
operating conditions (coolant
temperature, engine load etc.).
NO: One of the above conditions has
not been fulfilled.NONE
EGRET008:EGR solenoid
valve controlINACTIVE
Shows the condition of the EGR
valve control.
INACTIVE: The valve is not
controlled by the computer.
ACTIVE: The valve is controlled by
the computer.NONE
PreheatingET007:Pre-
postheating
controlACTIVE/INACTIVE
Shows the status of the preheating
unit control.In the event of a fault,
consult the interpretation
of fault DF017 Preheating
unit control circuit.

13B-122V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PARAMETER CHECK
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Idle speed
regulationPR010:Idle speed
regulation
setpointShows the speed of rotation
that the engine should reach
at idle speed: approximately
825 rpm.In the event of a fault, consult the
interpretation of faults DF007 Rail
pressure sensor circuit, DF024
Low pressure actuator control
circuit and DF053 Rail pressure
regulation function.
Accelerator
pedalPR030:Accelerator
pedal
positionPR030 = 0% (pedal
released)
Gives the accelerator pedal
position in %.In the event of a fault, apply the
interpretation of faults DF008 Pedal
potentiometer circuit gang 1,
DF009 Pedal potentiometer circuit
gang 2, DF113 Sensor supply
voltage and DF122 Pedal
potentiometer gang 2 supply
voltage.
Coolant
temperaturePR064:Coolant
temperatureWarm: 90°C
Indicates the engine coolant
temperature in °C.
Default value: 80°C.In the event of a fault, consult the
interpretation of parameter PR064.
Vehicle speedPR089:Vehicle
speedGives the vehicle speed in
mph (km/h).See fault finding for the ABS (see
38C, Anti-lock braking system).

13B-127V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
STATUS CHECK
NOTESOnly perform this conformity check after a complete check using the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine idling, warm engine, coolant temperature > 80°C.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
EngineET038:EngineRUNNING NONE
Engine
immobiliserET003:Engine
immobiliserINACTIVE
Indicates the status of the
immobiliser system.
INACTIVE: The injection computer
has recognised the immobiliser code
transmitted by the UCH.
ACTIVE: The injection computer
does not recognise the immobiliser
code transmitted by the UCH.If status ET003 is
inconsistent, consult the
fault finding procedure for
the UCH (See 82D,
Access – Security).
Air
conditioningET164:Configuration
with air
conditioningYES - NO
States whether the vehicle is fitted
with air conditioning or not.
YES: Air conditioning is detected by
the injection computer.
NO: Air conditioning is not detected
by the injection computer.If not consistent with the
vehicle equipment, test the
multiplex network and
follow the relevant
procedure.
Fast idle speedET023:Fast idle speed
requestABSENT
The UCH sends a fast idle request to
the injection.
ABSENT: no UCH request.
PRESENT: UCH request.If status ET023 is
inconsistent, consult the
fault finding procedure for
the UCH (See 87B,
Passenger compartment
connection unit).

13B-128V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
STATUS CHECK (CONTINUED 1)
NOTESOnly perform this conformity check after a complete check using the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine idling, warm engine, coolant temperature > 80°C.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Air
conditioningET116:Climate control
authorisationNO
YES: The UCH should send an
activation request to the injection.
The coolant pressure sensor must
not be defective. Satisfactory engine
operating conditions (coolant
temperature, engine load etc.).
NO: One of the above conditions has
not been fulfilled.NONE
EGRET008:EGR solenoid
valve controlINACTIVE
Shows the condition of the EGR
valve control.
INACTIVE: The valve is not
controlled by the computer.
ACTIVE: The valve is controlled by
the computer.In the event of a fault,
apply the interpretation of
faults DF016 EGR control
circuit and DF114 EGR
solenoid valve circuit
(not applicable to K9K796
Euro 2).
PreheatingET007:Pre-
postheating
controlACTIVE/INACTIVE
Shows the status of the preheating
unit control.In the event of a fault,
consult the interpretation
of fault DF017 Preheating
unit control circuit.

13B-129V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
STATUS CHECK (CONTINUED 2)
NOTESOnly perform this conformity check after a complete check using the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine idling, warm engine, coolant temperature > 80°C.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Brake
contactET122:Brake switch no.
1 signalINACTIVE
INACTIVE: Brake pedal released.
ACTIVE: Brake pedal depressed.In the event of a fault, refer
to the interpretation of
status ET122.
ET123:Brake switch no.
2 signalINACTIVE
Indicates recognition of brake pedal
contacts.
INACTIVE: Brake pedal released.
ACTIVE: Brake pedal depressed.If status ET123 is
inconsistent, run a
multiplex network test
using the diagnostic tool.
Clutch pedalET233:Clutch pedalRELEASED
Indicates recognition of clutch pedal
contacts.
RELEASED: Pedal released.
DEPRESSED: Pedal depressed.In the event of a fault,
consult the interpretation
of status ET233.

13B-130V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PARAMETER CHECK
NOTESOnly perform this conformity check after a complete check using the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine idling, warm engine, coolant temperature > 80°C.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Idle speed
regulationPR010:Idle speed
regulation
setpointShows the speed of rotation
that the engine should reach
at idle speed: approximately
825 rpm.In the event of a fault, consult the
interpretation of faults DF007 Rail
pressure sensor circuit, DF024
Low pressure actuator control
circuit and DF053 Rail pressure
regulation function.
Accelerator
pedalPR030:Accelerator
pedal
positionPR030 = 0 %
Gives the accelerator pedal
position in %.In the event of a fault, apply the
interpretation of faults DF008 Pedal
potentiometer circuit gang 1,
DF009 Pedal potentiometer circuit
gang 2, DF113 Sensor supply
voltage and DF122 Pedal
potentiometer gang 2 supply
voltage.
Coolant
temperaturePR064:Coolant
temperatureWarm: 90°C
Indicates the engine coolant
temperature in °C.
Default value: 80°C.In the event of a fault, consult the
interpretation of parameter PR064.
Vehicle speedPR089:Vehicle
speedGives the vehicle speed in
mph (km/h). This parameter
is sent by the ABS computer
or the vehicle speed
computer. Refer to fault finding for the ABS
system or the vehicle speed
computer.