2013 RENAULT KANGOO engine oil

13B-152
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP2 The engine will not start
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply test 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter
(see MR 388 (Logan/Sandero),
MR 451 (Duster), MR 423 (Thalia
2/Symbol 2) or MR 374 (Kangoo
VLL), Mechanical, 19B, Exhaust,
Catalytic converter: Removal -
Refitting).
Check the electrical circuit by running TEST 2 Electrical circuit check.
Check the electrical conformity of the heater plugs (the resistance of the heater plug must be less than 2 ).
YES
NO
A
DCM1.2_V08_ALP02

13B-155
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP3 The engine starts with difficulty, or starts then stalls
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply test 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR
388 (Logan/Sandero), MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2) or MR 374
(Kangoo VLL), Mechanical, 19B, Exhaust,
Catalytic converter: Removal - Refitting).
Check the electrical conformity of the heater plugs (the resistance of the heater plug must be less than 2 ).
YES
NO
A
DCM1.2_V08_ALP03

13B-163
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP7 Erratic acceleration/deceleration and engine racing
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the engine has not sucked up its oil (engine racing).
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Visually check the condition of the engine wiring harness.
Check the injectors by running TEST 3 Injector check.
Check the condition of the computer connections (for bent pins, signs of oxidation, silicone, etc.) and check that
the computer connectors lock correctly.
Contact the Techline if the customer complaint is still present.
DCM1.2_V08_ALP07

13B-166
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP9 Engine cut-out (stalling)
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply test 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check that the engine has not sucked up its oil (engine racing).
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR
388 (Logan/Sandero), MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2) or MR 374
(Kangoo VLL), Mechanical, 19B,
Exhaust, Catalytic converter: Removal
- Refitting).
Visually check the condition of the engine wiring harness.
YES
NO
A
DCM1.2_V08_ALP09

13B-170
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP11 Loss of power
NOTESSpecial note:
Only address this customer complaint after a complete check with the diagnostic
tool.
See explanation for flow capacity function in system operation.
Is status ET563 Flow capacity function "ACTIVE"?
Using the diagnostic tool, check that the
injector codes (C2I) are correctly
entered on the identification screen. If not,
configure the correct injector codes using
command SC002 Enter injector codesCheck the diesel filter.
Is it close to the replacement mileage?
Replace the diesel filter (see MR 388 (Logan/Sandero),
MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR
374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel
filter: Removal - Refitting).
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the engine oil level correct? Top up the oil level.
NOYES
NO
YES
NO
A
YES
DCM1.2_V08_ALP11

13B-172
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP12 Too much power
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
In this case, the control solenoid valve is jammed: it is possible to increase the vacuum but not reduce it
afterwards.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Check that the engine has not sucked up its oil (engine racing).
Check that the turbocharger is working properly.
Run TEST 11 Air line at the turbocharger.
Run TEST 10 Turbocharger solenoid valve check.
Run TEST 12 Turbocharger.
Check the condition of the computer connections (for bent pins, signs of oxidation, silicone, etc.) and check that
the computer connectors lock correctly.
Contact the Techline if the customer complaint is still present.
DCM1.2_V08_ALP12

13B-173
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP12
CONTINUED 1
In this case, it may be the solenoid valve dynamic specification which is at fault (atmospheric pressure
resetting time). Final fault finding is carried out by measuring this specification on a special bench.
Check that solenoid valve casing does not have any splashes of fluid on it which may impede the breather (water,
engine oil, gearbox oil, brake fluid, coolant, mud, dust, or any other substance).
Instructions:
The solenoid valve must be set up 450 mm above the ground, in an area free from water, mud, or any other fluid.
Cleaning with a high pressure jet is forbidden.
Is there coolant present?
Is the solenoid valve subjected to significant fluctuations or impacts?
Instructions:
The solenoid valve must be correctly secured to its mounting.
Contact with the engine environment is forbidden.Follow the
recommendations below.
Check the turbocharger regulation control (no
partial jamming, etc.).Follow the recommendations below.
NOYES
NOYES
AA

13B-175
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP 13 Excessive consumption
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.Replace the fuel temperature sensor (see MR
388 (Logan/Sandero), MR 423 (Thalia 2/Symbol
2), MR 451 (Duster) or MR 374 (Kangoo VLL),
Mechanical, 13B, Diesel injection, Rail pressure
sensor: Removal - Refitting). Is the fuel temperature sensor leaking?
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
Visually check that there are no leakages on the high pressure circuit by running TEST 7 High pressure circuit
sealing check.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
YES
NO
A
DCM1.2_V08_ALP13