2013 RENAULT KANGOO sensor

38C-48
AFTER REPAIRClear the computer memory using command RZ001 Fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-38C000$170.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault Finding Chart38C
ABS BOSCH 8.1
Vdiag No.: 18
ALP2
CONTINUED
Check that the wheel speed sensor mounting is in good condition (clipping).
Visually inspect the condition of the target (clogging, metallic contamination, etc.) and clean with compressed air
if necessary.
Check the condition of the braking system (condition of linings, sealing, grating, bleed, etc.).
Check the condition of the axles and the conformity and good condition of the tyre mountings.
If the fault is still present after these checks, contact the Techline.

38C-49
AFTER REPAIRClear the computer memory using command RZ001 Fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-38C000$170.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault Finding Chart38C
ABS BOSCH 8.1
Vdiag No.: 18
ALP3 Pull
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Disconnect one wheel speed sensor.
Start the engine and ensure that only the ABS fault warning light comes on. Do not drive the vehicle if the brake
fault warning light is also illuminated because the "braking compensator" function is no longer guaranteed.
Carry out a road test with the ABS thus out of order.
Is the fault still present under these conditions?
Raise the vehicle so that you can rotate the wheels and check:
– whether the speed sensors have been incorrectly
connected,
– whether the pipes on the hydraulic unit have been inverted.
For these two tests, consult and apply the procedures defined
in ALP2 Locking of one or several wheels.
Check the condition and conformity of the ABS targets.
If the fault is still present, contact the techline.If the brake pedal travel is relatively long,
bleed the brake circuit.
If the travel is normal, check the tyre
pressures, the front axle, or for any leaks in
the circuit.
NOYES
ABS8.1X76_V18_ALP3

38C-50
AFTER REPAIRClear the computer memory using command RZ001 Fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-38C000$170.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault Finding Chart38C
ABS BOSCH 8.1
Vdiag No.: 18
ALP4 Drift
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Disconnect one wheel speed sensor.
Start the engine and ensure that only the ABS fault warning light comes on. Do not drive the vehicle if the brake
fault warning light is also illuminated because the "braking compensator" function is no longer guaranteed.
Carry out a road test with the ABS thus out of order.
Is the fault still present under these conditions?
Normal behaviour linked to the system operation during
the regulation phase, mainly on surfaces with uneven
grip or which are poorly laid.Road holding fault not related to the ABS.
Check the condition of the brake linings and that
they are to specification and check the tyre
pressures, the front axle, etc.
NOYES
ABS8.1X76_V18_ALP4

38C-51
AFTER REPAIRClear the computer memory using command RZ001 Fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-38C000$170.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault Finding Chart38C
ABS BOSCH 8.1
Vdiag No.: 18
ALP5Unexpected ABS operation at low speed and slight pedal
pressure
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool. Warning: ABS control is sensitive to poor traction (icy roads, wet cobblestones,
etc.).
It is possible to feel brake pedal vibrations which are associated with the reaction of the system in particular
circumstances, such as:
– crossing rumble strips,
– tight cornering with lifting of the inside rear wheel.
These vibrations may be linked to simple brake limiter activation, when the pressure on the rear axle is limited.
If the fault is different, check the speed sensor connectors (micro-breaks).
ABS8.1X76_V18_ALP5