38C-45
AFTER REPAIRClear the computer memory using command RZ001 Fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-38C000$170.mif
38C
ABS BOSCH 8.1
Vdiag No.: 18
ALP1 No dialogue with the ABS computer
NOTESUse the Wiring Diagrams Technical Note for KANGOO VLL.
Try to establish dialogue with a computer on another vehicle to check that the diagnostic tool is not faulty. If the
tool is not causing the fault and dialogue cannot be established with any other computer on the same vehicle, it
may be that a faulty computer is disrupting fault finding line HK.
Use a process of successive disconnections to locate this computer.
Check the battery voltage and carry out the necessary operations to obtain a correct voltage between 9.8 V < X <
16.7 V.
Check the presence and condition of the ABS fuses on the passenger compartment fuse box, component code
260, F17 and in the engine fuse box, component code 710, F01 and F10, (see MR 374 Mechanical, 81C, Fuses,
Fuses: List and location of components).
Check the connection of the ABS computer connector, component code 118 and the condition of its connections.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the earths on the MQ connections of component 118 (good condition, not corroded, tightness of the earth
bolt on top of the ABS assembly).
Check that the supply to the computer is correct:
–Earth on the MQ connections of component 118,
–+ before ignition feed on connections BP14 and BP8 of component 118,
–+ after ignition feed on connection AP5 of component 118.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the connection of the diagnostic socket connector, component code 225 and the condition of its
connections.
Check the continuity of connection HL and HK between the computer and the diagnostic socket.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
A
ABS8.1X76_V18_ALP1
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault Finding Chart
38C-49
AFTER REPAIRClear the computer memory using command RZ001 Fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-38C000$170.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault Finding Chart38C
ABS BOSCH 8.1
Vdiag No.: 18
ALP3 Pull
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Disconnect one wheel speed sensor.
Start the engine and ensure that only the ABS fault warning light comes on. Do not drive the vehicle if the brake
fault warning light is also illuminated because the "braking compensator" function is no longer guaranteed.
Carry out a road test with the ABS thus out of order.
Is the fault still present under these conditions?
Raise the vehicle so that you can rotate the wheels and check:
– whether the speed sensors have been incorrectly
connected,
– whether the pipes on the hydraulic unit have been inverted.
For these two tests, consult and apply the procedures defined
in ALP2 Locking of one or several wheels.
Check the condition and conformity of the ABS targets.
If the fault is still present, contact the techline.If the brake pedal travel is relatively long,
bleed the brake circuit.
If the travel is normal, check the tyre
pressures, the front axle, or for any leaks in
the circuit.
NOYES
ABS8.1X76_V18_ALP3
38C-50
AFTER REPAIRClear the computer memory using command RZ001 Fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-38C000$170.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault Finding Chart38C
ABS BOSCH 8.1
Vdiag No.: 18
ALP4 Drift
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Disconnect one wheel speed sensor.
Start the engine and ensure that only the ABS fault warning light comes on. Do not drive the vehicle if the brake
fault warning light is also illuminated because the "braking compensator" function is no longer guaranteed.
Carry out a road test with the ABS thus out of order.
Is the fault still present under these conditions?
Normal behaviour linked to the system operation during
the regulation phase, mainly on surfaces with uneven
grip or which are poorly laid.Road holding fault not related to the ABS.
Check the condition of the brake linings and that
they are to specification and check the tyre
pressures, the front axle, etc.
NOYES
ABS8.1X76_V18_ALP4
