2013 RENAULT CLIO CUP Chapter c

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-18

B.6.3.1.8 DIAGNOSTIC PAGE 5 : CBNT DIAGNOSTIC (PAGE 1/2 : STATES)



Every indication corresponds to the XAP CBNT pinout and shows the state
(ON/OFF) of
each Pin. Please refer to chapter F- wiring for more details.

When XAP Master relay is ON :
- All values from the first column must be “ON” (gr een)

- On the second column, Steer W/A, starter and revG B Sol must be “ON” green, for the
other Pins, please find the action/result below :
Sensors
/actuators Signification Action result
stop light SW Brake Pedal
contactor switch Brake pedal pressed OFF >ON
rain light SW Rain light switch on facia switch
panel “Rain ” switch ON OFF >ON
light left SW Left side lights switch on steering
wheel “light” button pressed OFF >ON
light right SW Right side lights switch on steering
wheel “light” button pressed OFF >ON
ignition Ignition coils switch on facia switch
panel “ignition” switch ON OFF >ON
fuel pump Fuel tower pump (facia switch panel
manual mode or automatic mode) state “fuel pump” button pressed and/or
automatic fuel pump management OFF >ON
brake light Lateral rear brake light state
Brake pedal pressed OFF >ON
rain light** Rear central rain light state Brake pedal pressed
And/or « Rain » switch ON And/or pit limiter ON
And/or Reverse gear ratio engaged OFF >ON
wiper zero “Wiper” position state
When “wiper” leave its rest position ON>OFF

** Please refer to Central rear rain light activati on strategies in this chapter

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-19

B.6.3.2 Changing pages

The pages of the display may be changed by pressing on the push button ‘PAGE” of the
steering wheel - Pressing briefly on this button (one second) moves the display in the 3 driver
pages
- Pressing this button for longer (more than 2 second s) moves the display from
driver pages to diagnostic pages
- Pressing briefly on the button moves the display in the 5 diagnostic pages

You can return to the driver pages by pressing the button for a longer period (more than
2 seconds). The display returns to the first driver page

B.6.3.3 Leds / shiftlights



Shiftlights (8):
Shiftlight thresholds are fully configurable using the “Toolset” software, see chapter G-
Softwares
The LEDs light up in all gear ratios. By default, t he setup is the following one:

LEDs Alarm (2):
On the left side, 1 LED lights up when an engine al arm rises up
On the right side, 1 LED lights up when a Gearbox a larm rises up

These LEDs are associated with the message displaye d in the area “Default” and with the
letter recorded in the area “events”
Engine alarm LED gearbox
alarm LED
Shiftlights
5000 5200 5400 5600 5800 6000 6200 6300 Engine RPM at which LEDs
light up

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-22

B " Manifold P - def"
+ value in Blue 1 Left Electrical fault on manifold sensor -
B "Oil P - def"
+ value in Blue 1 Left Electrical fault on oil pressure sensor -
B
"Water T - def"
+ value in Blue 1 Left Electrical fault on water temperature sensor -
B
“Throt FBW * def”
+ value in blue 1 Left Electrical fault on motorised throttle
B
“High press def”
+ value in Blue 1 Left High pressure sensor default -
B
“Low press def”
+ value in Blue 1 Left Low pressure sensor default -
B
" V.V.T.1 - def"
+ value in Blue 1 Left Intake V.V.T. servo control default difference > 10°
between VVT1_tg and VVT1_pos during more than 5s
B “GB actuator - def”
+ value in Blue 1 Right Gearbox actuator default
(only if connected) -
B "GB Pot - def"
+ value in Blue 1 Right Electrical default on barrel position senso
r -
B “up contact – def”
+ value in Blue 1 Right Electrical default on upshift contactor -
B “Solenoid R”
+ value in Blue 1 Right Electrical default on reverse solenoid (barrel
unlocking) -
B "CBNT - Can Def" - CAN CBNT fault -
B "Steering - def" - Major/minor fault on power ste
ering module -
“Gear” - Gear button pressed, message displayed in the
middle of the screen without alarm

"Pit Limiter" - Speed limiter enabled, message displayed on the top of the screen without alarm
-

B.6.4 BASIC PROCEDURES
B.6.4.1 Power-up

Press the “ON” button of the facia switch panel
(See B.6.1) to power supply the vehicle
The “COSWORTH” home page appears when the dashboard display first comes on, and
then moves to the first driver page (RACE Page)
B.6.4.2 Starting

Once the vehicle’s electrics are on, flick the vehi cle's “IGNITION” switch to the up (ON)
position.
Check that no gear is engaged (the letter “N” is di splayed on one of the display screen’s
driver pages).
Press on the “START” button without touching the Gas Pedal


The vehicle will only start if the following elect ronic equipments are connected
and are working properly:
- ECU
- CBNT
- Master relay
It is possible to start without plugging the dashbo ard
NOTE :
For the first engine start after engine refitting, it’s necessary to bleed the fuel
rail. To make it properly, please follow carefully the procedure indicated in chapter C-
Engine

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-23

B.6.4.3 Turning off the engine

Flick the “IGNITION” switch to the down (OFF) posit ion

NOTE : The vehicle’s electrics remain switched on
Except in the event of an emergency stop, it’s stri ctly not advised to turn off the
engine using the power supply switch (OFF button).
It is also recommended to wait 30seconds between sw itching off the engine and
switching off the power supply.
Respecting these two recommendations will guarantee optimum operation of the power
steering.
B.6.4.4 Switching off the power supply

Press the “OFF” button of the facia switch panel an d hold there for at least half a second.
The dashboard display is switched off.
NOTE: Switching off the power supply also switches off th e engine.

B.6.4.5 Changing gears

2 modes are possible and are completely independent . It’s possible to make randomly
upshift and downshift manually (using the lever) or in semi-auto using paddle shift kit.

Please refer to Chapter D-Transmission/shifting for a complete description of the shifting
modes.
B.6.4.6 Pit limiter

The purpose of this function is to limit the vehicl e's speed to 60kph
. It is enabled and
disabled by the driver.
Principle:
By pressing the button “PIT” of the steering wheel, Engine revs are thus limited (by the
ECU) to those corresponding to a speed of 60kph and the message “PIT LIMITER” is
displayed on the dashboard in the RPM Area :