Page 38 of 734

WARNING!(Continued)
•Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or
others could be seriously or fatally injured. Chil-
dren should be warned not to touch the parking
brake, brake pedal or the shift lever.
• Do not leave the Key Fob in or near the vehicle, or
in a location accessible to children, and do not
leave a vehicle equipped with Keyless Enter-N-Go
in the ACC or ON/RUN mode. A child could
operate power windows, other controls, or move
the vehicle.
Power Door Locks — If Equipped
A power door LOCK switch is on each front door trim
panel. Use this switch to lock or unlock the doors. If you press the power door LOCK switch while the Key
Fob is in the ignition, and any front door is open, the
power locks will not operate. This prevents you from
accidentally locking your Key Fob in the vehicle. Remov-
ing the Key Fob or closing the door will allow the locks to
Power Door Lock Switch Location
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 41 of 734

WARNING!
Avoid trapping anyone in a vehicle in a collision.
Remember that the rear doors can only be opened
from the outside when the Child-Protection locks are
engaged.
NOTE:
• After setting the Child-Protection Door Lock system,
always test the door from the inside to make certain it
is in the desired position.
• For emergency exit with the system engaged, move the
door lock switch to the UNLOCK position, roll down
the window and open the door with the outside door
handle.
KEYLESS ENTER-N-GO™
The Passive Entry system is an enhancement to the
vehicle’s Remote Keyless Entry (RKE) system and a
feature of Keyless Enter-N-Go™. For further information,
refer to “Keyless Enter-N-Go™” in “STARTING AND
OPERATING”. This feature allows you to lock and
unlock the vehicle’s door(s) without having to press the
RKE transmitter lock or unlock buttons.
NOTE:
• Passive Entry may be programmed ON/OFF; refer to
“Uconnect® settings” in “Understanding Your Instru-
ment Panel” for further information.
• If wearing gloves on your hands, or if it has been
raining on the Passive Entry door handle, the unlock
sensitivity can be affected, resulting in a slower re-
sponse time.
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39
Page 47 of 734

WARNING!
•Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children to
be in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Children should be
warned not to touch the parking brake, brake pedal
or the shift lever.
• Do not leave the key fob in or near the vehicle (or
in a location accessible to children), and do not
leave a vehicle equipped with Keyless Enter-N-
Go™ in the ACC or ON/RUN mode. A child could
operate power windows, other controls, or move
the vehicle.
Auto-Down
Both the driver and front passenger window switch have
an Auto-Down feature. Press the window switch past the first detent, release, and the window will go down
automatically. To cancel the Auto-Down movement, op-
erate the switch in either the up or down direction and
release the switch.
To stop the window from going all the way down during
the Auto-Down operation, pull up on the switch briefly.
To open the window part way, press to the first detent
and release it when you want the window to stop.
Auto-Up Feature With Anti-Pinch Protection
(4-Door Models Driver And Front Passenger Door
Only) — If Equipped
Lift the window switch fully upward to the second
detent, release, and the window will go up automatically.
To stop the window from going all the way up during the
Auto Up operation, push down on the switch briefly.
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45
Page 128 of 734

▫Power Lumbar — If Equipped ............143
▫ Heated Seats — If Equipped ..............143
▫ Ventilated Seats — If Equipped ............146
▫ Manual Seat Adjuster — If Equipped ........147
▫ 40-20-40 Front Bench Seat — If Equipped . . . .148
▫ Mega Cab® Rear Seat Features ............148
▫ Head Restraints ..................... .153
DRIVER MEMORY SEAT — IF EQUIPPED . . . .155
▫ Programming The Memory Feature .........155
▫ Linking And Unlinking The Remote Keyless Entry
Transmitter To Memory .................157
▫ Memory Position Recall .................158
TO OPEN AND CLOSE THE HOOD .........158
LIGHTS ............................ .160
▫ Headlights ......................... .161
▫ Automatic Headlights — If Equipped .......161
▫ Headlights On With Wipers (Available With
Automatic Headlights Only) ..............162
▫ Daytime Running Lights (DRL) —
If Equipped ........................ .162
▫ Headlight Delay ..................... .163
▫ SmartBeam™ — If Equipped .............163
▫ Parking Lights And Panel Lights ...........165
▫ Fog Lights — If Equipped ...............165
▫ Lights-On Reminder ...................166
▫ Battery Saver ........................ .166
▫ Interior Lights ...................... .166
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 132 of 734

▫Plastic Grocery Bag Retainers (Regular Cab
Models) ........................... .223
REAR WINDOW FEATURES ..............224
▫ Rear Window Defroster .................224
▫
Power Sliding Rear Window — If Equipped . . .224
▫ Manual Sliding Rear Window —
If Equipped ........................ .225
FOLD FLAT LOAD FLOOR — IF EQUIPPED . . .225
PICKUP BOX ........................ .227
RAMBOX® — IF EQUIPPED ..............229
▫ RamBox® Integrated Box Side Storage Bins . . .230
▫ Locking And Unlocking RamBox® .........232
▫ RamBox® Safety Warning ................233
▫ Bed Extender — If Equipped .............234▫
Bed Rail Tie-Down System ..............241
SLIDE-IN CAMPERS ....................243
▫ Camper Applications ...................243
EASY-OFF TAILGATE ...................244
▫ Disconnecting the Rear Camera or Remote
Keyless Entry — If Equipped .............244
▫ Removing The Tailgate ..................245
▫ Locking Tailgate ..................... .246
TRI-FOLD TONNEAU COVER-IF EQUIPPED . . .247
▫ Tri-Fold Tonneau Cover — If Equipped ......247
▫ Tri-Fold Tonneau Cover Removal ..........247
▫ Tri-Fold Tonneau Cover Installation And
Cleaning ........................... .249
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 158 of 734

•The head restraints should only be removed by quali-
fied technicians, for service purposes only. If either of
the head restraints require removal, see your autho-
rized dealer.
DRIVER MEMORY SEAT — IF EQUIPPED
This feature allows the driver to store up to two different
memory profiles for easy recall through a memory
switch. Each memory profile contains desired position
settings for the driver seat, side mirrors, adjustable
pedals (if equipped) and a set of desired radio station
presets. Your Remote Keyless Entry (RKE) transmitter
can also be programmed to recall the same positions
when the UNLOCK button is pressed.
NOTE: Your vehicle is equipped with two RKE trans-
mitters. One RKE transmitter can be linked to memory
position 1 and the other transmitter can be linked to
memory position 2. The memory seat buttons are located on the outboard
side of the drivers seat cushion.
Programming The Memory Feature
NOTE:
To create a new memory profile, perform the
following:
Memory Seat Buttons
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 159 of 734

Vehicles Equipped With Keyless Enter-N-Go
1. Without pressing the brake pedal, push the ENGINESTART/STOP button and cycle the ignition to the
ON/RUN position (Do not start the engine).
2. Adjust all memory profile settings to desired prefer- ences (seat, side mirrors, adjustable pedals and radio
station presets).
3. Press and release the S (Set) button on the memory switch.
4. Within five seconds, press and release either of the memory buttons (1) or (2). The Electronic Vehicle
Information Center (EVIC) will display which
memory position has been set.
Vehicles Not Equipped With Keyless Enter-N-Go
1. Insert the ignition key fob, and turn the ignition switch to the ON/RUN position. 2. Adjust all memory profile settings to desired prefer-
ences (seat, side mirrors, adjustable pedals [if
equipped], power tilt and telescopic steering column
[if equipped], and radio station presets).
3. Press and release the S (Set) button on the memory switch.
4. Within five seconds, press and release either of the memory buttons (1) or (2). The Electronic Vehicle
Information Center (EVIC) will display which
memory position has been set.
NOTE:
• Memory profiles can be set without the vehicle in
PARK, but the vehicle must be in PARK to recall a
memory profile.
• The Recall Memory with Remote Linked to Memory
feature can be enabled through the Electronic Vehicle
Information Center (EVIC), refer to “Electronic Vehicle
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157
Page 160 of 734

Information Center (EVIC)/Customer-Programmable
Features” in “Understanding Your Instrument Panel”
for further information.
Linking And Unlinking The Remote Keyless Entry
Transmitter To Memory
Your RKE transmitters can be programmed to recall one
of two pre-programmed memory profiles by pressing the
UNLOCK button on the RKE transmitter.
NOTE:Before programming your RKE transmitters you
must select the “Remote Linked to Memory” feature
through the Electronic Vehicle Information Center
(EVIC), refer to “Electronic Vehicle Information Center
(EVIC)/Customer-Programmable Features” in “Under-
standing Your Instrument Panel” for further information. To program your RKE transmitters, perform the follow-
ing:
1. Remove the Key Fob from the ignition (or change the
ignition to OFF, for vehicles equipped with Keyless
Enter-N-Go).
2. Select desired memory profile (1) or (2).
NOTE: If a memory profile has not already been set,
refer to Programming The Memory Feature for instruc-
tions on how to set a memory profile.
3. Once the profile has been recalled, press and release the SET (S) button on the memory switch, then press
and release button (1) or (2) accordingly. “Memory
Profile Set” (1 or 2) will display in the instrument
cluster on vehicles equipped with the EVIC.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE