2013 Peugeot 308 SW BL service indicator

16
FAMILIARISATION
MONITORING

Instrument panel
Switch panel



A.
With the ignition on, the needle
should indicate the level of fuel
remaining.

B.
With the engine running, its
associated low level warning lamp
should switch off.

C.
With the ignition on, the oil level
indicator should indicate for a few
seconds that the level is correct or
OK, depending on version.
If the levels are not correct, top up the
levels which are low. Lighting of the indicator lamp indicates
the status of the corresponding function.


A.
Emergency call in progress.

243

B.
Deactivation of the alarm interior
volumetric monitoring.

87

C.
Central locking.

92

D.
Deactivation of the ESP/ASR
system.

140

E.
Deactivation of the front and rear
parking sensors.

168

F.
Access to PEUGEOT services.


243



1.
With the ignition on, the orange and
red warning lamps come on.

2.
With the engine running, these
warning lamps should go off.
If warning lamps remain on, refer to the
page concerned.

Warning lamps




25



29, 33

1
25
INSTRUMENTS and CONTROLS
TYPE 1 INSTRUMENT PANEL

Dials


5.
Screen.


6.
Control button.

Recalls the service information.
Resets the function to zero (trip
distance recorder or service
indicator).

7.
Instrument panel lighting button.

Adjusts the brightness of the lighting
of the instruments and controls.

1.
Rev counter.

Indicates the speed of rotation of
the engine (x 1000 rpm).

2.
Coolant temperature.

Indicates the temperature of the
engine coolant (° Celsius).

3.
Fuel level.

Indicates the quantity of fuel
remaining in the tank.

4.
Vehicle speed.

Indicates the current speed of the
moving vehicle (mph or km/h).

A.
Speed limiter

(mph or km/h) or
Cruise control.


B.
Gear shift indicator.


C.
6-speed electronic gear control
or automatic gearbox.


D.
Trip distance recorder.

(miles or km)

E.
Service indicator

(miles or km) then,
engine oil level indicator

then
distance recorder.

(miles or km)
These three functions are displayed
in succession when the ignition is
switched on.


Displays
For more information, refer to the
section on the button or function
and its associated display.

1INSTRUMENTS and CONTROLS












TYPE 2 INSTRUMENT PANEL

Dials


6.
Central screen.


7.
Control button.

Starts a manual CHECK and
recalls the service information.
Resets the function to zero (trip
distance recorder or service
indicator).

8.
Instrument panel lighting button.

Adjusts the brightness of the lighting
of the instruments and controls.

1.
Rev counter.

Indicates the speed of rotation of
the engine (x 1000 rpm).

2.
Coolant temperature.

Indicates the temperature of the
engine coolant (° Celsius).

3.
Fuel level.

Indicates the quantity of fuel
remaining in the tank.

4.
Vehicle speed.

Indicates the current speed of the
moving vehicle (mph or km/h).

5.
Small screen.


A.
Trip distance recorder.

(miles or km)

B.
Distance recorder.

(miles or km)

C.
Engine oil level indicator,

service indicator.

(miles or km)
These two functions are displayed
when the ignition is switched on,
then disappear after a few seconds.
Displays
For more information, refer to the
section on the button or function
and its associated display. The following functions are displayed
depending on the selection.


- Warning lamps / CHECK.



- Tyre under-infl ation detection.


- Speed limiter / Cruise control.


- Gear shift indicator.


- 6-speed electronic gear control
or automatic gearbox.


- Navigation - Guidance / Trip
computer.


- Alert messages symbol.

1INSTRUMENTS and CONTROLS












TYPE 3 INSTRUMENT PANEL WITH PEUGEOT CONNECT MEDIA
NAVIGATION (NG4 3D)


1.
Rev counter.

Indicates the speed of rotation of
the engine (x 1000 rpm).

2.
Coolant temperature.

Indicates the temperature of the
engine coolant (° Celsius).

3.
Fuel level.

Indicates the quantity of fuel
remaining in the tank.

4.
Vehicle speed.

Indicates the current speed of the
moving vehicle (km/h or mph).

5.
Small screen.


A.
Trip distance recorder.

(miles or km)

B.
Distance recorder.

(miles or km).

C.
Engine oil level indicator,

service indicator.

(miles or km)
These two functions are displayed
when the ignition is switched on,
then disappear after a few seconds.
The following functions are displayed
depending on the selection.


- Warning lamps / CHECK.


- Tyre under-infl ation detection.


- Speed limiter / Cruise control.


- Gear shift indicator.


- 6-speed electronic gear control
or automatic gearbox.


- Navigation - Guidance / Trip
computer.


- Vehicle and screen parameter
settings menus.


- Alert messages.






Dials


Displays

6.
Central screen.


7.
Control button.

Starts a manual CHECK and
recalls the service information.
Resets the function to zero (trip
distance recorder or service
indicator).

8.
Instrument panel lighting button.

Adjusts the brightness of the lighting
of the instruments and controls.
For more information, refer to the
section on the button or function
and its associated display.

1
40
INSTRUMENTS and CONTROLS






Service indicator

System which informs the driver when
the next service is due, in accordance
with the manufacturer's servicing
schedule.
The point at which the service is due is
calculated from the last indicator zero
reset. It is determined by two param-
eters:


- the distance travelled,

- the time elapsed since the last
service.
Between 600 miles (1 000 km) and
1 800 miles (3 000 km) remain before
the next service is due
For 5 seconds after the ignition is switched
on, the spanner symbolising the service
operations comes on. The distance re-
corder display line indicates the distance
remaining before the next service is due.

Example:
1 700 miles (2 800 km) re-
main before the next service is due.
For 5 seconds after the ignition is
switched on, the screen indicates:
5 seconds after the ignition is switched
on, the spanner goes off
; the distance
recorder resumes its normal operation.
The screen then indicates the total and
trip distances.
Less than 600 miles (1 000 km)
remain before the next service is due

Example:
560 miles (900 km) remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the screen indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation. The spanner re-
mains on
to indicate that a service
must be carried out soon.
More than 1 800 miles (3 000 km)
remain before the next service is due
When the ignition is switched on, no ser-
vice information appears in the screen.

1
41
INSTRUMENTS and CONTROLS
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve min-
utes for the zero reset to be reg-
istered.






Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:


)
switch off the ignition,

)
press and hold the ".../000"
button
on the right of the instrument panel,

)
switch on the ignition; the
distance recorder display begins a
countdown,

)
when the instrument panel central
screen indicates "=0"
, release the
button; the spanner disappears
from the screen. The distance remaining may be
weighted by the time factor, de-
pending on the driving conditions.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.

Service overdue
For 5 seconds after the ignition is
switched on, the spanner fl ashes
to
indicate that the service must be carried
out as soon as possible.

Example:
the service is overdue by 186 miles
(300 km).
For 5 seconds after the ignition is
switched on, the screen indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation. The spanner re-
mains on
.
Retrieving the service information
You can access the service information
at any time.
This information appears, depending
on version, when running through the
manual check procedure.


)
Briefl y press the ".../000"
button on
the right of the instrument panel.
The service information is
displayed for a few seconds on the
instrument panel central screen,
then disappears.

1
42
INSTRUMENTS and CONTROLS
The level shown will only be correct
if the vehicle is on level ground and
the engine has been off for more
than 30 minutes.















Engine oil level indicator

This information is displayed for a few
seconds when the ignition is switched
on, after the service information.

Oil level correct

Oil level low
Oil level indicator fault

Dipstick
This is indicated by the fl ashing of "OIL"
,
linked with the service warning lamp, ac-
companied by an audible signal and a
message in the multifunction screen.
If the low oil level is confi rmed by a
check using the dipstick, the level must
be topped up to prevent damage to the
engine. This is indicated by the fl ashing of "OIL--"
.
Contact a PEUGEOT dealer or a qualifi ed
workshop.
Refer to the "Checks" section to locate
the dipstick and the oil fi ller cap on your
engine.
There are 2 marks on the
dipstick:


- A
= max; never exceed
this level (risk of
damage to the engine),

- B
= min; top up the level
via the oil fi ller cap,
using the grade of oil
suited to your engine.

10
174
CHECKS
CHECKING LEVELS
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
If a level drops signifi cantly, have the
corresponding system checked by a
PEUGEOT dealer or a qualifi ed work-
shop.

Brake fluid level


On vehicles which are fi tted with a par-
ticle emission fi lter, the fan may oper-
ate after the vehicle has been switched
off, even if the engine is cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work.
To avoid any risk of scalding, unscrew the
cap by two turns to allow the pressure to
drop. When the pressure has dropped,
remove the cap and top up the level.

Oil level

The check is carried out either
when the ignition is switched on
using the oil level indicator on
the instrument panel, or using
the dipstick.
This manual check will only be correct
if the vehicle is on level ground and
the engine has been off for more than
30 minutes.
After topping up the oil, the check when
switching on the ignition with the oil level
indicator in the instrument panel will only
be valid 30 minutes after topping up. The brake fl uid level should be
close to the "MAX" mark. If it is
not, check the brake pad wear.

Changing the fl uid
Refer to the servicing booklet for details
of the interval for this operation.


Power steering fluid level

The power steering fl uid level
should be close to the "MAX"
mark. Unscrew the cap, with the
engine cold, to check the level.
Engine oil change
Refer to the servicing booklet for details
of the interval for this operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.

It is normal to top up the oil level
between services. PEUGEOT re-
commends that you check the oil
level and top up if necessary every
3 000 miles (5 000 kilometres).
Fluid specifi cation
The brake fl uid must conform to the
manufacturer's recommendations and
meet the DOT4 standard.

Changing the coolant
The coolant does not have to be changed.


Coolant level

The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm, the tempera-
ture of the coolant is regulated by the
fan. This can operate with the ignition
off.

Fluid specifi cation
The coolant must conform to the manu-
facturer's recommendations.

When working under the bonnet,
take care, as certain areas of the
engine may be extremely hot (risk
of burns).
Oil specifi cation
The oil must be the correct grade for
your engine and conform to the manu-
facturer's recommendations.