2013 Peugeot 208 fuel

194
Checks
Quality of the fuel used for
petrol engines
The petrol engines are per fectly compatible
with E10 or E24 type petrol biofuels (containing10 % or 24 % ethanol), conforming to Europeanstandards EN 228 and EN 15376.
E85 type
fuels (containing up to 85 % ethanol) are reserved exclusively for vehicles marketed
for the use of this type of fuel (BioFlex
vehicles). The quality of the ethanol mustcomply with European standard EN 15293.
For Brazil only, special vehicles are marketed
to run on fuels containing up to 100 % ethanol (E10 0 type).
Quality of the fuel used for
Diesel engines

The Diesel engines are per fectly compatible
with biofuels which conform to current andfuture European standards (Diesel fuel whichcomplies with standard EN 590 mixed with a
biofuel which complies with standard EN 14214)available at the pumps (containing up to 7 %Fatty Acid Methyl Ester).
The B30 biofuel can be used in cer tain Diesel engines; however, this use is subject to strict
application of the special ser vicing conditions.Contact a PEUGEOT dealer or a qualified
workshop.
The use of any other type of (bio)fuel (vegetable or animal oils, pure or diluted,
domestic fuel...) is strictly prohibited (risk of
damage to the engine and fuel system).

195
8
Checks
On vehicle fitted with HDi engines, the fuel system must be primed if you run out of fuel;
refer to the engine compar tment view on the
"Diesel engine" section.
If the tank on your vehicle is fitted with
a misfuel prevention device, refer to the corresponding section.












Running out of fuel (Diesel)


If the engine does not star t first time, don't keep trying. Star t the procedure again from the beginning.

)
Fill the fuel tank with at least five litres of
diesel.)
Open the bonnet.)
Press and release the priming pump until resistance is felt (there may be resistance
on the first press).
) Operate the star ter until the engine star ts. )
Close the bonnet.
1.4 litre HDi engine
)
Fill the fuel tank with at least five litres of diesel. )
Open the bonnet. )
If necessary, unclip the styling cover for
access to the priming pump. ) Squeeze and release the priming pump
repeatedl
y until resistance is felt (there may
be resistance at the first press). ) Operate the star ter until the engine star ts (if the engine does not star t at the first
attempt, wait around 15 seconds before
trying again).) If the engine does not star t after a few
attempts, operate the priming pump again
then star t the engine. ) Clip the styling cover back in place.)
Close the bonnet.



1.6 litre HDi engine

9
201
Technical data
.../S: model fitted with Stop & Star t.















Petrol engines and gearboxes
Engines1 litre VTi68 hp1.2 litre VTi 82 hp1.4 litre VTi 95 hp
Gearboxes

Manual(5-speed)
Manual (5-speed)

Electronic (5-speed)

Manual (5-speed)

Model codes: CC... CA...

ZMZ0


HMZ0 - HMX0
HMZ0/PS

8FP0 - 8FN0


Cubic capacity (cc) 999

1 1991 397
Bore x stroke
(mm)
71 x 84.1
75 x 90.577 x 75

Max power: EU standard (kW)
* 50
60

70

Max power engine speed
(rpm)
6 000 5 750 6 000
Max torque: EU standard
(Nm)95

118

136

Max torque en
gine speed (rpm) 3 000
2 750
4 000

Fuel Unleaded Unleaded Unleaded

Catalytic converter yes yes
yes

OIL CAPACITIES
(in litres)
Engine (with filter replacement) 3.13
3.13

4.25

*
The maximum power corresponds to the type approved value on a test bed, under conditions defined by European legislation (directive 1999/99/EC).

206
Technical data
* The maximum power corresponds to the type approved value on a test bed, under conditions defined by European legislation (directive 1999/99/EC).















Diesel engines and gearboxes
Engines 1.4 litre HDi68 hp1.4 litre e- HDi 68 hp1.6 litre e- HDi 92 hp
GearboxesManual (5-speed)Electronic(5-speed)


Manual (5-speed)

Model codes: CC... CA...
8HR0
8HP0/PS
9HP0/S
Cubic capacity (cc) 1 398

1 560

Bore x stroke
(mm)

73.7 x 8275 x 88.3

Max power: EU standard (kW)
* 50
68

Max power engine speed
(rpm)
4 000 4 000
Max torque: EU standard
(Nm) 160

230

Max torque en
gine speed (rpm)
1 750
2 000

Fuel Diesel
Diesel

Catalytic conver ter yes yes

P
article emission filter yes
yes

OIL CAPACITIES
(in litres)
Engine (with filter replacement) 3.75 3.75

...
/S: e-HDi model fitted with Stop & Start.

212
Technical data























Identifi cation markings
A.Vehicle Identification Number (VIN) under the bonnet.
This number is engraved on the bodyworknear the damper suppor t.

The tyre pressures must be checked when the tyres are cold, at least oncea month.


Low tyre pressures increase fuelconsumption.
B.Vehicle identification Number (VIN) on
the windscreen lower crossmember.This number is indicated on a self-adhesive label which is visible through the
windscreen.
C.Manufacturer's label. The VIN is indicated on a self-destroying
label affixed to the middle pillar, on the
passenger's side.
D.Tyre/paint label. This label is fitted to the middle pillar, on
the driver's side. It bears the
following information:


- the tyre inflation pressures with and without
load,

- the tyre sizes,

- the in
flation pressure of the spare wheel,

- the paint colour code. Various visible markin
gs for the identification of your vehicle.

04
219219
PEUGEOT CONNECT APPS
These intelligent applications use
vehicle data such as the current
speed, mileage, remaining fuel range or even GPS position to
provide useful information.
Plu
g the "PEUGEOT CONNECT" connection key into one the theUSB ports for access to the applications via the touch screen.
The "M
yPeugeot" application is alink between the user, PEUGEOTand the dealer network.
It
allows the customer to knoweverything about their vehicle:handbook, servicing booklet,accessory range, contracts takenout.
It also makes possible the sendin
g
of the vehicle's mileage to the "MyPeugeot" site, or to identify a dealer.


With "PEU
GEOT CONNECT APPS", the driver travels around while having access to useful information such as the state of the traffi c, the
availability of parking places, tourist sites, weather conditions, correct addressesÖ
This service includes access to the mobile network associated with the use o
f these applications. It is available according to country,subscription contract and the version of touch screen.

For obvious sa
fety reasons, some functions can only be used whenstationary.

Using "Plug & Play", the key is recognised automatically and allows
display of the interface giving access to the applications.

263
Level 1Level 2Level 3Comments
Settings
S
ystem confi guration
S
ystem
settingsBri
ghtnessT
urn off screen
Set the brightness. Adjust daytime brightness

Animations and scrolling:
Skin
s Change the environment.
Languages Select the language.
Date & Time
GPS Synchronisation:
Set the date and time.
Time format:
Other
Continue with other system settings
Units Set the units for the display of distance, fuel consumptionand temperature.
Delete data Select the desired data in the list then press Delete.
Settings Factory settings.
Confi rm
Save the settings.

08

MODIFY SYSTEM SETTINGS







SYSTEM

Select "System confi guration".


Press MENUto display the " MAIN MENU
" then select " Preferences".
Select " Other" to display the other settings.r

Select:
-
"Brightness
" to switch off the screen or
adjust the brightness.

- "
Languages
" to change the language.

- "
Units" to change the units used
for distance, fuel consumption and
temperature.
-"
Date & Time" to change the time zone,synchronisation with GPS, time and itsformat and then the date.


Select "Factory settings " to return to theoriginal settings.

Select "Delete data
" to delete the list of recent
destinations, personal points of interest,
contacts in the list.

Choose the item then select " Delete".

Select "Recent destinations" then press on
" Delete " and confi rm with the message.
SETTINGS
266