2013 Peugeot 208 display

90
Driving
Four-speed automatic gearbox which offers a choice between the comfor t of fully automatic operation, enhanced by spor t and snow
pro
grammes, or manual gear changing.
There are therefore four driving modes:-automatic
operation for electronic management of the gears by the gearbox,
-
sportprogramme for a more dynamic style
of driving,

- snowprogramme to improve driving when
traction is poor,

- se
quentialoperation for manual changing
of the gears by the driver.















Automatic gearbox
1.
Gear lever.2.
Button "S"(sport)
.
3.Button "7"(snow) .


Gear selection gateGear lever
P.Park.
- Immobilisation of the vehicle, parking brakeon or off.
- Starting the engine.
R. Reverse.
- Reversing manoeuvres, vehicle stationary, engine at idle.N.Neutral.
- Immobilisation of the vehicle, parking brakeon.
- Star ting the engine.D.
Automatic operation.M + / -. Manual operation with sequential changing of the four gears.)Push for wards to change up through
the
gears. or )Pull backwards to change down through
the gears.



Displays in the instrument panel

When you move the lever in the gate to select
a position, the corresponding indicator is
displayed in the instrument panel. P. ParkR.ReverseN.
NeutralD.Drive (Automatic driving) S.Sportprogramme 7.Snowprogramme1 2 3 4.
Gears engaged during manual
operation
-. Invalid value during manual operation


Foot on brake
)Press the brake pedal when thisindicator lamp is displayed in the
instrument panel (e.g.: star tingthe engine).

91
4
Driving
)Apply the parking brake. )Select position P or N.)Star t the engine.
If this procedure is not followed, there is an audible signal,
accompanied by the display of an warning message.

Moving off


When the engine is running at idle, with the brakes released, if position R, Dor M
is selected, the vehicle moveseven without the accelerator being pressed.
When the engine is running, never leave children in the vehicle without supervision.
When carrying out maintenance with the engine running, apply the parkingbrake and select position P
.
P


If position N
is selected inadver tently while driving, allow the engine toreturn to idle then select position D
toaccelerate.
Never select position N
while the vehicle is moving.Never select positions P
or Runless thevehicle is completely stationary.

Automatic operation
)
Select position Dfor automaticchanging
of the four gears.The gearbox then operates in auto-adaptivemode, without any inter vention on the par t
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
v
ehicle.
For maximum acceleration without touching the gear lever, press the accelerator pedal downfully (kick down). The gearbox changes downautomatically or maintains the gear selecteduntil the maximum engine speed is reached.On braking, the gearbox changes downautomatically to provide efficient engine
braking.
If you release the accelerator sharply, thegearbox will not change to a higher gear for
safety reasons.

Sport and snow programmes


Sport programme "S"
)
Press button "S", after star ting the engine.
The
gearbox automatically favours a dynamic style of driving.
S
appears in the instrument panel.


Snow programme " 7"
)
Press button "7
", after star ting the engine.
The gearbox adapts to driving on slipperyroads.
This programme improves star ting and drive
when traction is poor.
7 appears in the instrument panel.



Return to automatic
o
peration
) At any time, press the button selectedagain to quit the programme engaged and
return to auto-adaptive mode.
These two special programmes supplement the
automatic operation in very specific conditions of use.
)With the engine running, press
the brake pedal.
)Release the parking brake. )Select position R, Dor M.)
Gradually release the brake pedal.
The vehicle moves off immediately.

92
Driving
Manual operation
)Select position M for sequentialchanging
o
f the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the
instrument panel.

Invalid value duringmanual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage position P
or Nto place the gearbox in
neutral.
In both cases, apply the parking brake to immobilise the vehicle.


Operating fault
When the ignition is on, the lightingof this warning lamp, accompanied
by an audible signal and a message in the
multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.
When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not
operate in manual mode.

There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the P
position to another position when the battery is flat.
To reduce fuel consumption when at a prolonged standstill with the engine
running (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.

If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the
message disappears.

97
4
Driving





Speed limiter


System which prevents the vehicle fromexceeding the speed programmed by the driver.
When the programmed speed limit is reached,
pressing the accelerator pedal in the normalmanner no longer has any effect.

The speed limiter is switched onmanually: the programmed speed must be at least 20 mph(30 km/h).

The speed limiter is switched offby manual foperation of the control.

The programmed speed can be exceeded
temporarily by pressing the accelerator firmly.
To return to the programmed speed, simply slow down to a speed below the programmed speed.


The speed limiter cannot, in any circumstances, replace the need to respect speed limits, nor can it replace the need for vigilance andresponsibility on the par t of the driver.

1.Selection of speed limiter mode.
2. Speed limiter on/off.
Steering mounted controls

The programmed information is grouped
together in the instrument panel screen.
5.Speed limiter on/off indication.
6. Speed limiter mode selection indication. 7.Programmed speed value.8.
Selection of a memorised speed setting.


Displays in the instrument panel
The programmed speed remains in the memory
when the ignition is switched off.
3. Increase the programmed value.
4. Decrease the programmed value.

98
Driving
) Turn thumb wheel 1to the "LIMIT"position: the speed limiter mode
is selected but is not switched on(PAUSE).
You do not have to switch the speed limiter
on in order to set the speed.
Programming

On a steep descent or in the event of sharp acceleration, the speed limiter willnot be able to prevent the vehicle from exceeding the programmed speed.
To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- do not fit one mat on top of another.




Leaving limiter mode

Operatin
g fault
)Set the speed value by pressing button 2or 3.You can then change the programmed speed using buttons 2
and 3:- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.

Exceeding the programmed speed
)Switch the speed limiter back on by pressing button 4
again.


)Switch the speed limiter on by pressing button 4 .
)Switch the speed limiter off by pressing button 4: the display confirms that it has been switched off (PAUSE). In the event of a speed limiter fault, the speed
is cleared resultin
g in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a qualified workshop.
)Turn thumb wheel 1
to the "0"position:
the speed limiter mode is deselected. The
displa
y returns to the distance recorder.
Pressing the accelerator pedal to exceed the programmed speed will not have
any effect unless you press the pedal firmlypast the ypoint of resistance.eThe speed limiter is deactivated temporarily and the programmed speed, which
is still displayed, flashes.
Returning to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of the
programmed speed.

99
4
Driving




Cruise control
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.

Th
e cruise control is switched off
manually for by pressing the brake or clutch pedal or on
triggering of the electronic stability system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal.
Switching off the ignition cancels any programmed speed value.
1
.Selection of cruise control mode.
2. Cruise control stop/resume.
Steering mounted controls

The cruise control cannot, in any circumstances,replace the need to respect speed limits, nor canit replace the need for vigilance and responsibilityon the par t of the driver.


The programmed information is grouped
together in the instrument panel screen.
5.Cruise control stopped/resumed indication.
6. Cruise control mode selection indication.
7. Programmed speed value.8. Selecting a memorised speed setting.


Displays in the instrument panel
3.
Increase the programmed value. 4.
Decrease the programmed value. Th
e cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph (40 km/h), as well as the engagement of:


- fourth gear on a manual gearbox,

- second gear on an electronic or automatic
gearbox, in manual sequential mode,

- position A
on an electronic gearbox or position D
on an automatic gearbox.

100
Driving
) Turn thumb wheel 1to the "CRUISE"position: the cruise control mode
is selected but is not switched on(PAUSE).

Programming
You can then change the programmed speed using buttons 2
and 3:- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.

Intentional or unintentional exceedin
g of the programmed speed results
in flashing of this speed in the screen.
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically cancels theflashing of the speed.
When the cruise control is switched on,be careful if you maintain the pressure on one of the programmed speedchanging buttons: this may result in avery rapid change in the speed of your vehicle.
Do not use the cruise control on slippery roads or in heavy traffic. On a steep descent, the cruise controlwill not be able to prevent the vehicle from exceeding the programmed speed.
To avoid any risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- never fit one mat on top of another.




Operating fault
Leavin
g cruise control mode
)Turn thumb wheel 1 to the "0"position: the cruise control mode isdeselected. The display returns to the distance recorder.

Exceeding the programmed speed
)Set the programmed speed byaccelerating to the required speed, then press button 2or 3.
)Switch off the cruise control by pressing button 4
: the screenconfirms that it has been switched off (PAUSE).
)Switch the cruise control back on by pressing button 4again. In the event o
f a cruise control malfunction,
the speed is cleared resulting in flashing of the
dashes. Have it checked by a PEUGEOT dealer
or a qualified workshop.

101
4
Driving








Memorising speeds
This memorisation of speeds applies to both the speed limiter and the cruise control.
You can memorise up to 5 speed settings in the system. By default, a few speeds are already memorised.


Memorisation

To select a memorised speed: )
press and hold button " + " or "- "; the systemstops at the closest memorised speed,)
press and hold button " +
" or "-
" again toselect another memorised speed.

A reminder of the speed and the state of thesystem (on / off) is displayed in the instrument
panel.
) Go to the main menu bypressing MENU.
For safety reasons, the driver mustcarry out these operations when stationary.


Selection
)Select the "Preferences" menu then "Vehicle".)Select the "Vehicle configuration" menu
then "Speeds memorised". )Choose the speed setting you want tomodify then select "Modify speed".)Enter the desired speed and press confirm
to save the modifications.