2013 Peugeot 208 change time

199
8
Checks






Checks
12 V battery
The battery does not require any maintenance.
However, check that the terminals are clean
and correctl
y tightened, particularly in summer and winter.
The presence of this label, in particular with
the Stop & Star t system, indicates the use of
a specific 12 V lead-acid battery with special
technology and specification. The involvement
of a PEUGEOT dealer or a qualified workshop is essential when replacing or disconnecting
the battery.
Particle emissions filter (Diesel)

The star t of saturation of the particle filter is indicated by the fixed
illumination of this warning lamp
accompanied by a warning message
in the screen (if a display screen isfitted).
On a new vehicle, the first particlefilter regeneration operations may beaccompanied by a "burnt" smell, which is perfectly normal.
Following prolonged operation of thevehicle at very low speed or at idle, you may, in exceptional circumstances, notice the emission of water vapour atthe exhaust on acceleration. This does
not affect the behaviour of the vehicle or the environment.
Unless other wise indicated, check these components in accordance with the ser vicin
g and warranty booklet and according to your engine.
Other wise, have them checked by a PEUGEOT dealer or a qualified workshop.
Air filter and passenger compartment filter

Refer to the ser vicing and warrantybooklet for details of the replacement
inter vals for these components.
Oil filter
Replace the oil filter each time theengine oil is changed.
Refer to the servicing and warrantybooklet for details of the replacement
interval for this component. Depending on the environment
(e.g. dustyatmosphere) and the use of the vehicle(e.g. city driving), replace them twice as oftenif necessary.y
A clogged passenger compartment filter may have an adverse effect on the per formance
of the air conditioning system and generateundesirable odours. When carr
ying out work on the battery, refer
to the "Practical information" section for
details of the precautions to be taken before
disconnecting the battery and following its
reconnection.
As soon as the traffic conditions permit,
regenerate the filter by driving at a speed of at
least 40 mph (60 km/h) until the warning lamp goes off.
If the warning lamp stays on, this indicates a
low additive level.

05

ADDING A WAYPOINT
ORGANISING WAYPOINTS

Select "Navigation GPS ".

Select "Waypoints
".

Select "Add
".

The address of the wa
ypoint is entered in
the same way as a destination, so enter
the " City" or post code, the "Street" andthe " N°". Confi rm each time.
Th
en select " As waypoint
".
Select the wa
ypoint that you want to move in
the order.
To or
ganise waypoints, carry out the previous operations 1 to3 again (Adding a waypoint).

Select "Up
".

Select "Down".

Select "Delete
".

Select "Road map
" to view the changes made
to the route.
Select "Guide
".

Select the criteria then "Confi rm
" to start guidance and give the general direction of the navigation route.

Pr
ess MENUto display the " MAIN MENU
" then select " Navigation".
NAVIGATION - GUIDANCE

Select "Address
".

263
Level 1Level 2Level 3Comments
Settings
S
ystem confi guration
S
ystem
settingsBri
ghtnessT
urn off screen
Set the brightness. Adjust daytime brightness

Animations and scrolling:
Skin
s Change the environment.
Languages Select the language.
Date & Time
GPS Synchronisation:
Set the date and time.
Time format:
Other
Continue with other system settings
Units Set the units for the display of distance, fuel consumptionand temperature.
Delete data Select the desired data in the list then press Delete.
Settings Factory settings.
Confi rm
Save the settings.

08

MODIFY SYSTEM SETTINGS







SYSTEM

Select "System confi guration".


Press MENUto display the " MAIN MENU
" then select " Preferences".
Select " Other" to display the other settings.r

Select:
-
"Brightness
" to switch off the screen or
adjust the brightness.

- "
Languages
" to change the language.

- "
Units" to change the units used
for distance, fuel consumption and
temperature.
-"
Date & Time" to change the time zone,synchronisation with GPS, time and itsformat and then the date.


Select "Factory settings " to return to theoriginal settings.

Select "Delete data
" to delete the list of recent
destinations, personal points of interest,
contacts in the list.

Choose the item then select " Delete".

Select "Recent destinations" then press on
" Delete " and confi rm with the message.
SETTINGS
266