Page 151 of 324
149
7
Practical information
2. Infl ation
)
Connect the compressor's electric plug to
the vehicle's 12 V socket. ) Star t the vehicle again and leave theengine running.
)
Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch B
in position "O"and press button C), in accordance with the vehicle's
tyre pressure label (located on the left hand
door aperture).
A loss of pressure indicates that thepuncture has not been fully plugged; contact a PEUGEOT dealer or qualified
workshop for assistance. ) Remove and stow the kit. )
Drive at reduced speed (50 mph [80 km/h]max) limiting the distance travelled to
approximately 120 miles (200 km).
As soon as possible, go to a PEUGEOTdealer or a qualified workshop.Yo u m u s t i nform the technician that you have used this kit. After inspection, the technician will advise you on whether the tyre can be repaired or if it must be replaced.
)Turn the selector A
to the "air" position. )Uncoil the black pipe Hfully. )Connect the black pipe to the
valve of the wheel.
Page 152 of 324
150
Practical information
Removing the cartridge
) Stow the black pipe. )
Detach the angled base from the white pipe. )
Suppor t the compressor ver tically. )
Unscrew the car tridge from the bottom.
Beware of discharges of fluid.
The expiry date of the fluid is indicated on the car tridge.
The sealant car tridge is designed for
single use; even if only partly used, itmust be replaced. After use, do not discard the car tridge into the environment, take it to anauthorised waste disposal site or aPEUGEOT dealer.
Do not forget to obtain a new sealantcartridge, available from PEUGEOT dealers or from a qualified workshop.
Checking tyre pressures /
inflatin
g accessories
You can also use the compressor, without injecting any product, to:
- check or adjust the pressure of your tyres,
- inflate other accessories (balls, bicycle
tyres...).
)
Turn the selector A
to the "Air"
position.
) Uncoil the black pipe H
fully. )
Connect the black pipe to the
valve of the wheel or accessory.
If necessary, fit one of the adaptorssupplied with the kit first.
)Connect the compressor's electrical connector to the vehicle's 12 V socket. )Star t the vehicle and let the engine run. )Adjust the pressure using the compressor (to inflate: switch B in position "I"
; to deflate: switch B
in position "O"and press button C), according to the vehicle's tyrepressure label or the accessory's pressure
label. )Remove the kit then stow it.
Page 153 of 324
151
7
Practical information
Changing a wheel
The tools are installed in the boot under the floor.
To gain access to them: )open the boot, )lift the floor and remove it. )remove the polystyrene spacer, )remove the carrier box containing the tools.
Access to the tools
List of tools *
3."Bolt cover" tool.
For removing the bolt protectors
(covers)on alloy wheels.4.Socket for the security bolts (located in theglove box).
For adapting the wheelbrace to the special
"security" bolts.
5.Towing eye.
See "Towing the vehicle".
Procedure for chan
ging a faulty wheel for the spare wheel using the tools provided with the vehicle.
All o
f these tools are specific to your vehicle andcan vary according to the level of equipment. Donot use them for other purposes.
1.Wheelbrace.
For removing the wheel trim and removing
the wheel bolts.
2. Jack with integral handle.For raising the vehicle.
*
Depending on country of sale.
Page 154 of 324
152
Practical information
Wheel with trim
When refitting the wheel
, refit the trimstarting by placing its notch facing thevalve and press around its edge withthe palm of your hand.
The spare wheel is installed in the boot under
th
e floor.
It is the "space-saver" type.
To gain access to it, refer to the paragraph"Access to the tools" on the previous page.
Access to the spare wheel *
Ta k i ng out the wheel
)Unscrew the yellow central bolt. )Raise the spare wheel towards you from
the rear. )Take the wheel out of the boot.
* Dependin
g on country of sale.
Page 161 of 324
159
7
Practical information
Changing a bulb
Front lamps
In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal surface of the glass of the headlamps and rear lampsis normal; it disappears after the lamps have been on for a few minutes.
The headlamps are fitted with polycarbonate glass with a protectivecoating:
)do not clean them using a dr y or abrasive cloth, nor with a detergent or solvent product, )
use a sponge and soapy water or apH neutral product, )
when using a high pressure washer on persistent marks, do not keep the lance directed towards thelamps or their edges for too long, so as not to damage their protectivecoating and seals, )
do not touch the bulb directly withyour fingers, use lint-free cloths.
Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of serious burns). It is imperative to use only anti-ultraviolet (UV) type bulbs in order notto damage the headlamp.
Always replace a failed bulb with a new bulb with the same type andspecification.1
.Daytime running lamps / sidelamps(light emitting diodes - LEDs).2. Dipped beam headlamps (H7-55W).3.Direction indicators (PWY-24W).4.Main beam headlamps (H7-55W).5.Front foglamps (with "corneringlighting" function according to version) (PSX-24W).
Page 166 of 324
164
Practical information
These bulbs are changed from inside the boot:
)open the boot, )remove the access grille from the corresponding side trim panel, )slacken and remove the nut, )disconnect the lamp unit connector, )remove the lamp unit carefully by it pullingin line towards the outside,
)
press the retaining tabs and remove the
bulb holder,
) turn the bulb a quar ter of a turn and change it.
To r e a s s e m b l e , c a r ry out these operations in reverse order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
Page 179 of 324
177
7
Practical information
Towing the vehicle
Access to the tools
The towing eye is installed in the boot under
the floor.
To gain access to it: )open the boot, )lift the floor and remove it,
)remove the towing eye from the holder.
General recommendations
Obser ve the legislation in force in your country. Ensure that the weight of the towing vehicle is higher than that of the towed vehicle. The person at the wheel of the towed vehicle must have a valid driving licence.When towing a vehicle with all four wheels on the ground, always use an approved towingbar; rope and straps are prohibited. When towing a vehicle with the engine off, there is no longer any power assistance for braking or steering.
In the following cases, you must always call on a professional recovery service: - vehicle broken down on a motor way or fast road, - 4 wheel drive vehicle, - when it is not possible to put the gearbox into neutral, unlock the steering, or release theparking brake, - towing with only two wheels on the ground, - where there is no approved towing bar available...
Procedure for havin
g your vehicle towed or for towing another vehicle using a removable towing eye.
Page 180 of 324
178
Practical information
To w i ng your vehicle
To w i ng another vehicle
)On the front bumper, unclip the cover by inserting the flat end of the towing eye in
the bottom of the cover. )Screw the towing eye in fully. )Install the towing bar.
)On the rear bumper, unclip the cover by pressing at the bottom. )Screw the towing eye in fully. )Install the towing bar. )Switch on the hazard warning lamps on
both vehicles. )Move off gently, drive slowly and for a shor t distance.
)Place the gear lever in neutral (position Non an electronicgearbox or automatic gearbox).Failure to observe this instruction could result in damage to certain components (braking, transmission...) and the absenceof braking assistance the next timethe engine is star ted.
) Unlock the steering by turning the key
in the ignition one notch and release the
parking brake. ) Switch on the hazard warning lamps onboth vehicles.
)
Move off gently, drive slowly and for a shor tdistance.
