Page 24 of 324
22
Instruments and controls
Active matrix instrument panel
Dials and screens
Control buttons
1.
Engine coolant temperature gauge. 2.
Rev counter (x 1 000 rpm or tr/min),
graduation according to engine (petrol or Diesel).3. Cruise control or speed limiter settings.4.
Gear shift indicator for a manual gearbox
or gear lever position and gear for an
electronic or automatic gearbox. 5. Speedometer (mph or km/h).
A.Main lighting dimmer. B.Instrument panel mood lighting.
C.Recall of the service information.
Reset the selected function (service
indicator or trip distance recorder).
6
. Service indicator, then total distance
recorder (miles or km).
These functions are displayed successively on switching on the ignition.
7.Trip distance recorder (miles or km).8. Analogue speedometer (mph or km/h).9.Fuel gauge.
Page 30 of 324
28
Instruments and controls
Warning lamps
When the engine is running or the vehicle is being driven, illumination of one of the following warning lamps indicates a fault which requires action on
the par t of the driver.
Any fault resulting in the illumination of a warning lamp must be investigated further by reading the associated message in the screen.
If you encounter any problems, contact a PEUGEOT dealer or a qualified workshop.
Warning / indicator lampStateCauseAction / Observations
STOPfixed, associated with another warning lamp. Major faults have occurred. Stop as soon as it is safe to do so.
Park, switch off the ignition and call a PEUGEOT
dealer or qualified workshop.
Servicefixed, associated with another warning lamp. Major faults have occurred. Refer to the section on this warning lamp and youmust then contact a PEUGEOT dealer or qualified
workshop.
fix
ed associated with a message (if a displayscreen is fitted). F
aults have occurred for which there
is no specific warning lamp. Identify the fault by reading the message shown in the screen (if a display screen is fitted) and refer to the corresponding section:
- engine oil level alert,
- risk of blockage of the par ticle emissions filter (Diesel).
- Diesel fuel additive level (Diesel with particle
emissions filter).
You must contact a PEUGEOT dealer or a qualified
workshop.
Page 32 of 324
30
Instruments and controls
Warning / indicator lampStateCauseAction / Observations
Engine autodiagnosis system
fixed. The emission control system has a
fault. The warning lamp should go off when the engine is started.
If it does not go off, contact a PEUGEOT dealer or qualified
workshop without delay.
flashing.The engine management system hasa fault. Risk of destruction of the catalytic conver ter.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
fixed, associated with theSERVICE warning lamp.
A minor engine fault has beendetected.Have it checked by a PEUGEOT dealer or a qualified
workshop.
fixed
, associated with
the STOP warning lamp. A ma
jor engine fault has been detected.You must stop as soon as it is safe to do so.
Park, switch off the ignition and contact a PEUGEOT
dealer or a qualified workshop.
Low fuel levelfixed with the needle
in the red zone. There remains approximately 5 litresof fuel in the tank.
At this point, you begin to use the fuel reserve.Re
fuel as soon as possible to avoid running out of fuel.
This warning lamp will come on every time the ignition
is switched on, until a sufficient addition of fuel is
made.
Fuel tank capacity: approximately 50 litres .
Never continue to drive until you run out of fuel, as
this could damage the emission control and injectionsystems.
flashing with the needle in the redzone.There remains ver
y little fuel in the
tank.
Page 40 of 324
38
Instruments and controls
System that gives you information on
the journey in progress (range, fuelconsumption…).
Tr i p c o m p u t e r
Instrument panel screen
Information displa
y
)
Press the button on the end of the wiper control stalkto display the various tabs insuccession.
- Th
e current information tab with:
●
the range,
●
the current fuel consumption,
●
the Stop & Start time counter.
-
Trip "1"with:
●
the average speed.
●
the average fuel consumption,
●
the distance travelled,
for the first trip.
- Tr i p
"2"
with:
●
the average speed,
●
the average fuel consumption,
●
the distance travelled,
for the second trip.
Page 42 of 324
40
Instruments and controls
System which provides current information concerning the trip (range, fuel consumption…).
Trip computer with touch screen
Information display
- The current fuel consumption tab
with:
●
the range,
●
the current
fuel consumption,
●
the Stop & Star t time counter.
-
The trip "1"tab with:
●
the distance travelled.
●
the average fuel consumption,
●
the average speed,
for the first trip.
- The trip
"2"
tab with:
●
the distance travelled.
●
the average fuel consumption,
●
the average speed,
for the second trip.
)Press MODElocated on the
touch screen front panel, to
displa
y the various tabs. )Select the desired tab using your finger.
Page 44 of 324
42
Instruments and controls
Stop & Start time counter
(minutes / seconds or hours /
minutes)
If dashes are displayed continuously while driving in place of the digits, contact a PEUGEOT dealer or a qualified workshop.
This function is only displayed from 20 mph (30 km/h).
This value may vary following a changein the style of driving or the relief,resulting in a significant change in thecurrent fuel consumption.
Trip computer, a few definitions
Range
(miles or km)
The distance which can still be
travelled with the fuel remainingin the tank. Related to theaverage fuel consumption over
the last few miles (kilometres)
travelled.
When the ran
ge falls below 20 miles (30 km),
dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (10 0 km).
Current fuel consumption
(mpg or l/100 km or km/l) Calculated over the last few seconds.
Average fuel consumption
(mpg or l/100 km or km/l) Calculated since the last trip computer reset.
Average speed
(mph or km/h)Calculated since the last trip computer reset.
Distance travelled
(miles or km)
Calculated since the last trip
computer reset.
If
your vehicle is fitted with Stop & Star t, a timecounter calculates the time spent in STOP mode during a journey. It resets to zero every time the ignition isswitched on with the key.
Page 72 of 324
70
Comfort
) Switch off the demisting/defrosting of the rear screen and door mirrorsas soon as appropriate, as lower current consumption results inreduced fuel consumption.
Front demist - defrost
Rear screen
demist - defrost
The control button is located on theair conditioning system control panel.
These markin
gs on the control panel indicate the control positions for rapid demisting or
defrosting of the windscreen and side windows.
With manual air
conditioning
Switching on
The rear screen demisting/defrosting can onlyoperate when the engine is running. )Press this button to demist/defrost the rear screen and (depending on version) the door mirrors. The indicator lamp associated with
the button comes on.
With Stop & Star t, when demisting has been activated, the STOP mode is not available.
Switching off
The demisting/defrosting switches off automatically
to prevent an excessive consumption of current. )It is possible to stop the demisting/defrosting
operation before it is switched off automatically
by pressing the button again. The indicator lamp associated with the button goes off.
With dual-zone digital air
conditioning
Automatic visibility programme )Put the temperature and distributioncontrols to the dedicated marked position. )Switch on the air conditioning by pressing
the "A/C"button; the warning lamp in thebutton comes on.
) Select this programme to demist or defrost
the windscreen and side windows as quickly as possible.
The system automatically manages the air conditioning, air flow and air intake, and
provides optimum distribution towards the
win
dscreen and side windows. ) To stop the programme, press either the "visibility"button again or "AU TO "
, the
warning lamp on the button goes off and
the warning lamp in the "AU TO "buttoncomes on.
The system rever ts to the previous settings.
Page 84 of 324
82
Driving
Gear lever positions
N
. Neutral R
. Reverse 1, 2, 3, 4, 5.
Gears in sequential mode AUTO.
This comes on when the automatedmode is selected. It switches off on changing to sequential mode.
)Select position N. )Press the brake pedal fully. )Star t the engine.
Nappears in the instrument panel.
Moving off
N
flashes in the instrument panelscreen if the gear lever is not inposition N
on starting.
)
Place your foot on the brakewhen this warning lamp flashes(e.g.: star ting the engine).
There is an audible signal on engagement of reverse.
When moving off on a slope, accelerate gradually while releasing the parking brake.
)
Select first gear (position Mor A
) or Areverse (position R)R )
Release the parking brake. )
Progressively take your foot off the brakepedal, then move off.
AUTO
and 1
or R
appear in the
instrument panel.
Stopping - Moving off on a slope
When stopping on a slope, do not use the
accelerator to immobilise the vehicle; apply the
parkin
g brake.
Sequential mode
AUTOdisappears and the gearsengaged appear in succession in the
instrument panel.
)After star ting the vehicle, select position Mto change to sequential mode.
The
gear change commands are only carried
out if the engine speed permits.
When driving at low speed, on approachinga stop sign or traffic lights for example,
the gearbox changes down to first gear
automatically.
You must press the brake pedal while star ting
the en
gine.
Automated mode
)Following use of the sequential mode, select position A
to return to the automated mode.
AUT
Oand the gear engaged appear in the instrument panel.
The gearbox then operates in auto-adaptive mode, without any action on the par t of the
driver. It continuously selects the most suitable
gear for:
- optimisation of fuel consumption,
- the drivin
g style,
- the road conditions,
- th
e vehicle load.
