2013 NISSAN MURANO instrument panel

Black plate (342,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
4-136Monitor, heater, air conditioner, audio, phone and voice recognition systems
Repeat the command in a clear voice.
. Push the BACK button once to return to the
previous screen.
. If you want to cancel the command, push
and hold the TALK
switch for 1 second.
The message “Voice canceled” will be
announced.
. To skip the voice guidance function and give
the command immediately, press the TALK
switch to interrupt the system. Remem-
ber to speak after the tone.
. If you want to adjust the volume of the
system feedback, push the volume control
switch (+ or −) on the steering wheel or use
the audio system volume knob while the
system is making an announcement.
How to speak numbers:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407NISSAN Voice Recognition requires a certain
way to speak numbers when giving voice
commands. Refer to the following examples.
General rule
Only single digits 0 (zero) to 9 can be used. (For
example, if you would like to say 500, “five zero
zero” can be used, but “five hundred” cannot.
Phone numbers
Speak phone numbers according to the follow-
ing examples: .
1-800-662-6200
— “Dial one eight zero zero six six two six
two zero zero.”
Note 1: For the best voice recognition phone
dialing results, say phone numbers as single
digits.
Note 2: You cannot say 555-6000 as “five five
five six thousands”.
Note 3: When speaking a house number, speak
the number “0” as “ zero”. If the letter “o (oh)” is
included in the house number, it will not be
recognized as the number “0 (zero)” even if you
speak “oh” instead of “zero”. Please speak
“zero” for the number “0 (zero)”, “oh” for the
letter “o (oh)”.
Send digits using dial tone:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407. Press the TALKswitch during a phone
call.
. The menu will be launched and you will be
provided with the following guidance:
"Please say the digits to dial".
. After guidance, say the digits of the number
you want to send. After this, the digits that
have been recognized will be read out.
. If you press the ENTER button on the
steering wheel or on the multi-function
controller, the selected digits will be sent.
SAA2549
Speaker adaptation function (for Alter-
nate Command Mode)
GUID-41540706-ED56-43AC-A84A-CB1ABE3F371AThe voice recognition system has a function to
learn the user’s voice for better voice recognition
performance. The system can memorize the
voices of up to three persons.
Having the system learn the user’s voice:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C4071. Push the SETTING button on the instrument
panel and select the “Others” key.
2. Select the “Voice Recognition” key.
3. Select the “Speaker Adaptation” key.
Condition:

Black plate (344,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
4-138Monitor, heater, air conditioner, audio, phone and voice recognition systems
SAA2553
Speaker Adaptation function settings:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Edit User Name
Edit the user name using the keypad displayed
on the screen.
Delete Voice Data
Resets the user’s voice that the voice recogni-
tion system has learned.
Continuous Learning
When this item is turned to ON, you can have
the system learn the voice commands in
succession, without selecting commands one
by one.
Minimize voice feedback (for Alternate
Command Mode)
GUID-2C83B6D4-4D4E-444E-A5EE-B27DB7DE0C05To minimize the voice feedback from the system,
perform the following steps.
1. Push the SETTING button on the instrumentpanel.
2. Select the “Others” key.
3. Select the “Voice Recognition” key.
4. Select the “Minimize Voice Feedback” key.
5. The setting is turned to ON and the voice guidance will now be reduced when using
the Voice Recognition system.
Condition:

Black plate (358,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-12Starting and driving
SSD0436
Operating range for engine start functionGUID-A596920A-CBFC-4976-89DB-4A47CB018FD5The Intelligent Key functions can only be used
for starting the engine when the Intelligent Key is
within the specified operating range
*1.
When the Intelligent Key battery is almost
discharged or strong radio waves are present
near the operating location, the Intelligent Key
system’s operating range becomes narrower
and may not function properly.
If the Intelligent Key is within the operating
range, it is possible for anyone, even someone
who does not carry the Intelligent Key, to push
the ignition switch to start the engine. .
The cargo/trunk area is not included in the
operating range, but the Intelligent Key may
function.
. If the Intelligent Key is placed on the
instrument panel, rear parcel shelf, inside
the glove box or door pocket, the Intelligent
Key may not function.
. If the Intelligent Key is placed near the door
or window outside the vehicle, the Intelligent
Key may function.
SSD1021
PUSH-BUTTON IGNITION SWITCH
OPERATION
GUID-0FA0E46E-E6F4-42C7-B398-B61C483B7F1BWhen the ignition switch is pushed without
depressing the brake pedal, the ignition switch
position will change as follows:
.Push center once to change to ACC.
. Push center two times to change to ON.
. Push center three times to change to OFF.
(No position illuminates.)
. Push center four times to return to ACC.
. Open or close any door to return to LOCK
during the OFF position.
The ignition lock is designed so that the ignition
switch position cannot be switched to LOCK
Condition:

Black plate (364,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-18Starting and driving
SSD0692
Overdrive (O/D) OFF switchGUID-8A3D61C2-25AC-4088-A419-A1EAB3D4657FWhen the O/D OFF switch is pushed with the
selector lever in the D (Drive) position, the
indicator light in the instrument panel illuminates.
Use the overdrive off mode when you need
improved engine braking.
To turn off the overdrive off mode, push the O/D
OFF switch again. The
indicator light will
turn off.
Each time the engine is started, or when the
selector lever is shifted to any position other
than the D (Drive) position, the overdrive off
mode will be automatically turned off.
Accelerator downshift — In D position —GUID-CD19E66D-4772-4785-B00D-BC9BC6AC4E04For passing or hill climbing, fully depress the
accelerator pedal to the floor. This shifts the
transmission down into a lower gear, depending
on the vehicle speed.
High fluid temperature protection modeGUID-FE0DB0A0-F4AF-44F6-8609-E1599FEA814DThis transmission has a high fluid temperature
protection mode. If the fluid temperature be-
comes too high (for example, when climbing
steep grades in high temperature with heavy
loads, such as when towing a trailer), engine
power and, under some conditions, vehicle
speed will be decreased automatically to reduce
the chance of transmission damage. Vehicle
speed can be controlled with the accelerator
pedal, but the engine and vehicle speed may be
limited.
Fail-safeGUID-CA9C7C97-9363-4621-960F-9DED536408A1If the vehicle is driven under extreme
conditions, such as excessive wheel spin-
ning and subsequent hard braking, the
fail-safe system may be activated. The MIL
may illuminate to indicate the fail-safe
mode is activated. (See “Malfunction In-
dicator Light (MIL)” in the “2. Instruments
and controls” section.) This will occur even
if all electrical circuits are functioning
properly. In this case, place the ignition switch in the OFF position and wait for 10
seconds. Then place the ignition switch
back in the ON position. The vehicle should
return to its normal operating condition. If
it does not return to its normal operating
condition, have a NISSAN dealer check the
transmission and repair if necessary.
WARNING
When the high fluid temperature pro-
tection mode or fail-safe operation
occurs, vehicle speed may be gradually
reduced. The reduced speed may be
lower than other traffic, which could
increase the chance of a collision. Be
especially careful when driving. If ne-
cessary, pull to the side of the road at a
safe place and allow the transmission
to return to normal operation, or have it
repaired if necessary.
Condition:

Black plate (368,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-22Starting and driving
BSW SYSTEM OPERATIONGUID-57C34072-19AD-4F92-8527-4EC338107115The BSW system operates above approximately
20 MPH (32 km/h) .
When the camera unit detects vehicles in the
detection zone, the Blind Spot Indicator light
located inside the outside mirrors will illuminate.
If the turn signal is then activated, the system
chimes (twice) .
SSD1026
Detection zoneGUID-EDF6517E-4B22-4DBC-B7D0-02DAE5036383The camera unit can detect vehicles on either
side of your vehicle when part of another vehicle
is within the detection zone shown as illustrated.
This detection zone typically starts from the
outside mirror of your vehicle and extends
approximately 10 ft (3 m) behind the rear
bumper, and approximately 10 ft (3 m) sideways.
NOTE:
The Blind Spot Indicator light will illumi-
nate for a few seconds when the ignition
switch is placed in the ON position.
The brightness of the Blind Spot Indicator lights
is adjusted automatically depending on thebrightness of the ambient light.
A chime sounds if the camera unit has already
detected vehicles when the driver activates the
turn signal. If a vehicle comes into the detection
zone after the driver activates the turn signal,
then only the Blind Spot Indicator light flashes
and no chime sounds. (See “BSW driving
situations” later in this section.)
Turning on or off the BSW systemGUID-C47C5086-5272-41CD-9A3F-A6BA43F0B737The BSW system can be turned on or off using
the setting menu on the center display.
SYSTEM ON:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The BSW light (green) on the instrument panel
will light up.
SYSTEM OFF:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The BSW light (green) on the instrument panel
will go out.
Condition:

Black plate (372,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-26Starting and driving
SSD1034
If the driver activates the turn signal while
another vehicle is in the detection zone, then
the Blind Spot Indicator light flashes and a
chime will sound twice.
JVS0154X
SSD0672
LDW light (orange, green)
LDW SYSTEM OPERATIONGUID-5A428BA7-251A-49AB-8955-F9AF33E9CC89The LDW system operates above approximately
43 MPH (70 km/h) .
When the vehicle approaches either the left or
the right of the traveling lane, the LDW system
will chime a sound and the LDW light (orange)
on the instrument panel will blink to alert the
driver.
The LDW system is not designed to operate
under the following conditions.
.When you operate the lane change signal
and change traveling lanes in the direction of
the signal. (The LDW system will become
operable again approximately 2 seconds
after the lane change signal is turned off.)
. When the vehicle speed is less than
approximately 43 MPH (70 km/h) .
After the above conditions have finished and the
necessary operating conditions are satisfied, the
LDW functions will resume.
Condition:

Black plate (373,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
Turning on or off the LDW systemGUID-1EF8AD82-14EA-4DE4-82CA-349DE5262573The LDW system is turned on or off using the
setting menu on the center display.
SYSTEM ON:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The LDW light (green) on the instrument panel
will light up.
SYSTEM OFF:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The LDW light (green) on the instrument panel
will go out.
JVS0159X
SSD0885
Example
Perform the following steps to enable or disable
the BSW system.
1. Push the SETTING
*1button and highlight
the “Driver Assistance” key on the display
using the multi-function controller. Then
push the ENTER
*2button.
Starting and driving5-27
Condition:

Black plate (379,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-76A875B9-D302-49EA-808D-3131A08DF31D.Keep your engine tuned up.
. Follow the recommended scheduled main-
tenance.
. Keep the tires inflated to the correct
pressure. Low tire pressure increases tire
wear and lowers fuel economy.
. Keep the wheels in correct alignment.
Improper alignment increases tire wear and
lowers fuel economy.
. Use the recommended viscosity engine oil.
(See “Engine oil and oil filter recommenda-
tion” in the “9. Technical and consumer
information” section.)GUID-789B8744-E030-429A-8E1D-A540048EE2D3
WARNING
.For AWD equipped vehicles, do not
attempt to raise two wheels off the
ground and shift the transmission to
any drive or reverse position with
the engine running. Doing so may
result in drivetrain damage or un-
expected vehicle movement which
could result in serious vehicle da-
mage or personal injury.
. Do not attempt to test an AWD
equipped vehicle on a 2-wheel dy-
namometer (such as the dynam-
ometers used by some states for
emissions testing) or similar equip-
ment even if the other two wheels
are raised off the ground. Make sure
that you inform the test facility
personnel that your vehicle is
equipped with AWD before it is
placed on a dynamometer. Using
the wrong test equipment may re-
sult in drivetrain damage or unex-
pected vehicle movement which
could result in serious vehicle da-
mage or personal injury.
SSD0418
ALL-WHEEL DRIVE (AWD) LOCK
SWITCH OPERATIONS
GUID-59E847D3-AC63-4E97-B941-A563BA7CB53EThe AWD LOCK switch is located on the lower
side of the instrument panel (CrossCabriolet
models) or on the center console (Hardtop
models) . This switch is used to select the AUTO
or LOCK mode depending on the driving
conditions.
Each time you push the lower part of the switch
*A, the AWD mode will switch:
AUTO ?LOCK ?AUTO.
Starting and driving5-33
INCREASING FUEL ECONOMY ALL-WHEEL DRIVE (AWD) (if so
equipped)
Condition: