2013 NISSAN MURANO display

Black plate (145,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SIC3250
PERSONAL LIGHTS (Hardtop models)GUID-649CAF7C-2CCF-4E76-A1BD-9F34B3E94A95
RearGUID-0958BB58-F974-4165-8A79-D4E6DD15AACDPush the button as illustrated to turn the light on
or off.
SIC4239
INTERIOR LIGHT CONTROL SWITCHGUID-2A6055BA-7B37-4FE4-B397-77EF5A05A796The interior light control switch has three
positions: ON, DOOR and OFF.
ON positionGUID-7462AA90-5FAE-4F84-925A-24F0133E09B3When the switch is in the ON position*1the
map lights and rear personal lights will illumi-
nate.
DOOR positionGUID-2534F567-EC7E-4D89-9E58-CCFFC0DDC2B3When the switch is in the DOOR position*2,
the map lights and rear personal lights will
illuminate under the following conditions:
. ignition switch is switched to the LOCK
position — remain on for about 15 seconds.
. doors are unlocked by pushing the UN-
LOCK button on the Intelligent Key or door
handle request switch with the ignition
switch in the LOCK position
— remain on for about 15 seconds.
. any door is opened and then closed with the
ignition switch in the LOCK position
— remain on for about 15 seconds.
. any door is opened with the ignition switch
in the ACC or ON position
— remain on while the door is opened.
When the door is closed, the lights go
off.
The lights will also turn off after a period of
time when the lights remain illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.
Models with color display:
When the auto interior illumination is set to the
OFF position (see “Vehicle information and
settings” in the “4. Monitor, heater, air condi-
tioner, audio, phone and voice recognition
systems” section) , the lights will illuminate under
the following condition:
. any door is opened with the ignition switch
in any position
Instruments and controls2-61
Condition:

Black plate (158,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-6Pre-driving checks and adjustments
Crosscabriolet modelsGUID-E42A3CA3-AD22-4044-A8E7-1CE5A91D11A8.Turning the driver’s door key cylinder to the
rear of the vehicle
*2will lock all doors.
. Turning the driver’s door key cylinder once
to the front of the vehicle
*1will unlock the
driver’s door. After returning the key to the
neutral position
*3, turning it to the front
again within 5 seconds will unlock all doors.
Models with color display:
You can switch the lock system to the mode that
allows you to open all the doors when the key is
turned once. (See “How to use SETTING
button” in the “4. Monitor, heater, air conditioner,
audio, phone and voice recognition systems”
section.)
OPENING AND CLOSING WINDOWS
WITH THE MECHANICAL KEY
GUID-5CA6B107-CCEF-4728-83E6-1D0247152077The driver’s door key operation also allows you
to open and close the window that is equipped
with the automatic open/close function. (See
“Power windows” in the “2. Instruments and
controls” section) .
To open the windows, turn the driver’s door key
cylinder to unlock for longer than 1 second.
The door is unlocked and the window keeps
opening while turning the key.
This function can also be performed by pushing
and holding the door UNLOCK button of the key. (See “Remote keyless entry system” later in
this section.)
To close the windows, turn the driver’s door key
cylinder to lock for
longer than 1 second. The
door is locked and the window keeps closing
while turning the key.
SPA2465
LOCKING WITH INSIDE LOCK KNOBGUID-280B5B43-891E-4CBE-9845-1698016E3BD4To lock the door individually, move the inside
lock knob to the lock position
*1then close the
door.
To unlock, move the inside lock knob to the
unlock position
*2.
When locking the door without Intelligent
Key, be sure not to leave the Intelligent
Key inside the vehicle.
Condition:

Black plate (163,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
prevent the Intelligent Key from being left in
the vehicle.
. The door handle request switch is opera-
tional only when the Intelligent Key has been
detected by the Intelligent Key system.
. To prevent the Intelligent Key from being left
inside the vehicle or the trunk, make sure you
carry the key with you and then lock the
doors or the trunk.
. Do not pull the door handle before pushing
the door handle request switch. The door
will be unlocked but will not open. Release
the door handle once and pull it again to
open the door.
. The Intelligent Key system (opening/closing
doors with the door handle request switch)
can be set to remain inactive on the center
display (if so equipped). (See “Vehicle
information and settings” in the “4. Monitor,
heater, air conditioner, audio, phone and
voice recognition systems” section.)
SPA2408
INTELLIGENT KEY OPERATIONGUID-11F409E1-2083-4E3E-98C3-276AB17A6B02You can lock or unlock the doors without taking
the key out from your pocket or bag.
SPA2779
SPA2780
Hardtop models
Pre-driving checks and adjustments3-11
Condition:

Black plate (166,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-14Pre-driving checks and adjustments
sound and the trunk will open.
BATTERY SAVER SYSTEMGUID-20E66BAB-355C-4A3F-B30F-61C4E89141BDWhen all the following conditions are met for a
period of time, the battery saver system will cut
off the power supply to prevent battery dis-
charge.
.The ignition switch is in the ACC position,
and
. All doors are closed, and
. The selector lever is in the P (Park) position.
WARNING SIGNALSGUID-737B9BCC-17DA-4349-B877-AC71EFB1D933To help prevent the vehicle from moving
unexpectedly by erroneous operation of the
Intelligent Key listed on the following chart or
to help prevent the vehicle from being stolen,
chime or beep sounds inside and outside the
vehicle and a warning displays in the dot matrix
liquid crystal display.
When a chime or beep sounds or the warning
displays, be sure to check the vehicle and
Intelligent Key.
See “Troubleshooting guide” later in this section
and “Dot matrix liquid crystal display” in the “2.
Instruments and controls” section.
Condition:

Black plate (167,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
TROUBLESHOOTING GUIDEGUID-E1D6756A-F1B8-472A-887B-B4B6682D8BDF
SymptomPossible causeAction to take
When pushing the ignition switch
to stop the engine The SHIFT P warning appears on the display
and the inside warning chime sounds con-
tinuously.
The selector lever is not in the P (Park)
position.
Shift the selector lever to the P (Park)
position.
When shifting the selector lever
to the P (Park) position. The inside warning chime sounds continuously.
The ignition switch is in the ACC or ON
position.Push the ignition switch to the OFF posi-
tion.
When opening the driver’s door
to get out of the vehicle The inside warning chime sounds continuously. The ignition switch is in the ACC
position.
Push the ignition switch to the OFF posi-
tion.
The Intelligent Key is in the Intelligent
Key port. Remove the Intelligent Key from the Intelli-
gent Key port.
When closing the door after get-
ting out of the vehicle The NO KEY warning appears on the display,
the outside chime sounds 3 times and the
inside warning chime sounds for a few
seconds.
The ignition switch is in the ACC or ON
position.
Push the ignition switch to the OFF posi-
tion.
The SHIFT P warning appears on the display
and the outside chime sounds continuously. The ignition switch is in the ACC or OFF
position and the selector lever is not in
the P (Park) position.Move the selector lever to the P (Park)
position and push the ignition switch to the
OFF position.
When closing the door with the
inside lock knob turned to LOCK The outside chime sounds for a few seconds
and all the doors unlock. The Intelligent Key is inside the vehicle
or cargo/trunk room area.
Carry the Intelligent Key with you.
When pushing the request switch
or the LOCK
button on the
Intelligent Key to lock the door The outside chime sounds for a few seconds. The Intelligent Key is inside the vehicle
or cargo/trunk room area.
Carry the Intelligent Key with you.
A door is not closed securely. Close the door securely.
When closing the trunk lid
(CrossCabriolet models) The outside chime sounds for approximately 10
seconds and the trunk lid opens.
The Intelligent Key is inside the trunk.
Carry the Intelligent Key with you.
Pre-driving checks and adjustments3-15
Condition:

Black plate (197,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
.Never pour fuel into the throttle
body to attempt to start your vehi-
cle.
. Do not fill a portable fuel container
in the vehicle or trailer. Static elec-
tricity can cause an explosion of
flammable liquid, vapor or gas in
any vehicle or trailer. To reduce the
risk of serious injury or death when
filling portable fuel containers:
— Always place the container on
the ground when filling.
— Do not use electronic devices when filling.
— Keep the pump nozzle in contact with the container while you are
filling it.
— Use only approved portable fuel containers for flammable liquid.
CAUTION
. If fuel is spilled on the vehicle body,
flush it away with water to avoid
paint damage. .
Insert the cap straight into the fuel-
filler tube, then tighten the fuel-filler
cap until a single click is heard.
Failure to tighten the fuel-filler cap
properly may cause the
mal-
function indicator light (MIL) to
illuminate. If the
light illumi-
nates because the fuel-filler cap is
loose or missing, tighten or install
the cap and continue to drive the
vehicle. The
light should turn off
after a few driving trips. If the
light does not turn off after a few
driving trips, have the vehicle in-
spected by a NISSAN dealer.
For additional information, see
“Malfunction Indicator Light (MIL)”
in the “2. Instruments and controls”
section.
. The LOOSE FUEL CAP warning will
appear if the fuel-filler cap is not
properly tightened. It may take a few
driving trips for the message to be
displayed. Failure to tighten the
fuel-filler cap properly after the
LOOSE FUEL CAP warning appears
may cause the
Malfunction
Indicator Light (MIL) to illuminate.
SPA2442
To remove the fuel-filler cap:
1. Turn the fuel-filler cap counterclockwise to remove.
2. Put the fuel-filler cap on the cap holder
*A
while refueling.
To install the fuel-filler cap:
1. Insert the fuel-filler cap straight into the fuel- filler tube.
2. Turn the fuel-filler cap clockwise until a single click is heard.
Pre-driving checks and adjustments3-45
Condition:

Black plate (198,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-46Pre-driving checks and adjustments
SPA2833
LOOSE FUEL CAP warningGUID-A04C09C8-3C53-423B-AC70-189E634F9E83The LOOSE FUEL CAP warning appears on the
dot matrix liquid crystal display when the fuel-
filler cap is not tightened correctly after the
vehicle has been refueled. It may take a few
driving trips for the message to be displayed. To
turn off the warning, perform the following steps:
1. Remove and install the fuel-filler cap as soonas possible. (See “Fuel-filler cap” earlier in
this section.)
2. Tighten the fuel-filler cap until a single click is heard.
3. Push the reset switch
*Aon the right side
of the combination meter for about 1 second to turn off the LOOSE FUEL CAP warning
after tightening the fuel cap.
GUID-24FBE4B2-4508-4AC7-A4F2-026DF692853E
WARNING
.
Do not adjust the steering wheel
while driving. You could lose control
of your vehicle and cause an acci-
dent.
. Do not adjust the steering wheel
any closer to you than is necessary
for proper steering operation and
comfort. The driver’s air bag inflates
with great force. If you are unrest-
rained, leaning forward, sitting side-
ways or out of position in any way,
you are at greater risk of injury or
death in a crash. You may also
receive serious or fatal injuries from
the air bag if you are up against it
when it inflates. Always sit back
against the seatback and as far
away as practical from the steering
wheel. Always use the seat belts.
TILT/TELESCOPIC STEERING
Condition:

Black plate (207,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
4 Monitor, heater, air conditioner, audio, phoneand voice recognition systems
Safety note ...
........................................................................\
.......... 4-3
Center multi-function control panel (models with color
display screen) ...
........................................................................\
.. 4-3
How to use multi-function controller ...
.............................. 4-5
How to use touch screen (models with
navigation system) ...
.............................................................. 4-5
Menu options (models with navigation system) ...
.......... 4-7
How to select menus on the screen ...
.............................. 4-8
Vehicle information and settings (if so equipped) ...
............ 4-9
How to use STATUS button ...
............................................. 4-9
How to use brightness control and display
ON/OFF button ...
................................................................... 4-9
How to use INFO button ...
.................................................. 4-9
How to use SETTING button ...
....................................... 4-13
RearView monitor (if so equipped) ...
................................... 4-23
How to read the displayed lines ...
.................................. 4-24
How to park with predictive course lines ...
.................. 4-24
Difference between predictive and
actual distances ...
................................................................ 4-26
Predictive course line settings ...
.................................... 4-28
How to adjust the screen ...
............................................. 4-28
Operating tips ...
................................................................... 4-29 Rear and rear-wide view monitor with Moving Object
Detection (MOD) (if so equipped)
...
................................... 4-30
How to switch the display ...
........................................... 4-31
How to park with predictive course lines ...
................ 4-33
How to adjust the screen ...
............................................ 4-37
Operating tips ...
................................................................. 4-37
Moving Object Detection (MOD) function ...
.............. 4-37
Ventilators ...
........................................................................\
........ 4-40
Heater and air conditioner ...
.................................................. 4-41
Automatic operation ...
...................................................... 4-43
Manual operation ...
............................................................ 4-44
To turn the system ON/OFF ...
....................................... 4-45
Operating tips ...
................................................................. 4-45
In-cabin microfilter ...
......................................................... 4-45
Servicing air conditioner ...
.............................................. 4-45
Audio system ...
........................................................................\
.. 4-46
Audio operation precautions ...
....................................... 4-46
FM-AM radio with Compact Disc (CD) changer ...
..... 4-61
FM-AM-SAT radio with Compact Disc
(CD) player ...
...................................................................... 4-66
DVD (Digital Versatile Disc) player operation
(models with navigation system) ...
................................ 4-70
Condition: