2013 NISSAN MURANO seat adjustment

Black plate (1,1)
Condition:
Illustrated table of contents0
Safety — Seats, seat belts and supplemental
restraint system1
Instruments and controls
Pre-driving checks and adjustments
Monitor, heater, air conditioner, audio, phone and
voice recognition systems
Starting and driving
In case of emergency
Appearance and care
Maintenance and do-it-yourself
Technical and consumer information
Index
2
3
4
5
6
7
8
9
10
Table of
Contents
[ Edit: 2012/ 7/ 31 Model: Z51-D ]

Black plate (24,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-2Safety — Seats, seat belts and supplemental restraint system
GUID-2869D0FF-2DAC-47DC-BF36-8D864A5BD9A3
SSS0133
WARNING
.Do not ride in a moving vehicle
when the seatback is reclined. This
can be dangerous. The shoulder belt
will not be against your body. In an
accident, you could be thrown into it
and receive neck or other serious
injuries. You could also slide under
the lap belt and receive serious
internal injuries.
. For the most effective protection
when the vehicle is in motion, the
seat should be upright. Always sit well back in the seat with both feet
on the floor and adjust the seat
properly. See “Precautions on seat
belt usage” later in this section.
. After adjustment, gently rock in the
seat to make sure it is securely
locked.
. Do not leave children unattended
inside the vehicle. They could un-
knowingly activate switches or con-
trols. Unattended children could
become involved in serious acci-
dents. .
The seatback should not be reclined
any more than needed for comfort.
Seat belts are most effective when
the passenger sits well back and
straight up in the seat. If the seat-
back is reclined, the risk of sliding
under the lap belt and being injured
is increased.
CAUTION
When adjusting the seat positions, be
sure not to contact any moving parts to
avoid possible injuries and/or da-
mages.
SEATS
Condition:

Black plate (25,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS0792
FRONT SEATSGUID-589050CC-5D5C-4407-A4F0-CB0819F0ABAB
Manual seat adjustmentGUID-6BE5370B-3D84-4E0B-B0E0-081F8AF0F764
Forward and backward:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Pull the lever*1up and hold it while you slide
the seat forward or backward to the desired
position. Release the lever to lock the seat in
position.
Reclining:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407To recline the seatback, pull the lever*2up and
lean back. To bring the seatback forward, pull
the lever up and lean your body forward. Release
the lever to lock the seatback in position.
The reclining feature allows adjustment of the seatback for occupants of different sizes for
added comfort and to help obtain proper seat
belt fit. (See “Precautions on seat belt usage”
later in this section.) Also, the seatback can be
reclined to allow occupants to rest when the
vehicle is stopped and the transmission in the P
(Park) position.
JVR0034X
Sliding front passenger seat (CrossCab-
riolet models):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407To slide the front passenger seat from the front
most position to the rear most position, push the
bottom half of the seatback
*Aor the front seat
cushion
*B. If you push the top half of the
seatback
*C, it will lock the seat in the front
most position.
Safety — Seats, seat belts and supplemental restraint system1-3
Condition:

Black plate (26,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-4Safety — Seats, seat belts and supplemental restraint system
SSS0793
Seat lifter (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Pull up or push down the adjusting lever to
adjust the seat height until the desired position
is achieved.
SSS0684
Lumbar support (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The lumbar support feature provides lower back
support to the driver.
Move the lever
*1up or down to adjust the
seatback lumbar area.
Power seat adjustmentGUID-2155E48C-B77E-4502-84B7-2AF110D60DE4
Operating tips:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407. The power seat motor has an auto-reset
overload protection circuit. If the motor
stops during operation, wait 30 seconds,
then reactivate the switch.
. Do not operate the power seat switch for a
long period of time when the engine is off.
This will discharge the battery.
See “Automatic drive positioner” in the “3. Pre-
driving checks and adjustments” section for the
seat position memory function (if so equipped).
Condition:

Black plate (28,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-6Safety — Seats, seat belts and supplemental restraint system
JVR0039X
Reclining:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Move the recline switch*Abackward until the
desired angle is obtained. To bring the seatback
forward again, move the switch
*Aforward.
Push and hold the back
*2end of the reclining
switch
*Buntil the desired angle is obtained.
To bring the seatback forward again, push and
hold the front
*1end of the switch (Cross-
Cabriolet models driver’s seat only).
The reclining feature allows adjustment of the
seatback for occupants of different sizes for
added comfort and to help obtain proper seat
belt fit. (See “Precautions on seat belt usage”
later in this section.) Also, the seatback can be
reclined to allow occupants to rest when the vehicle is stopped and the transmission is in the
P (Park) position.
SSS1027
Seat lifter (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Push the front or rear end of the switch up or
down to adjust the angle of the front portion or
height of the seat.
Condition:

Black plate (30,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-8Safety — Seats, seat belts and supplemental restraint system
Alternatively, you can push the remote walk-
in switch located on the instrument panel to
fold down the front passenger’s seatback
and unlock the seat position.
2. Slide the seat forward to the foremost
position manually.
3. Get in or out the vehicle.
4. Return the front passenger seat to the
rearmost position. To slide the front passen-
ger seat, see “Manual seat adjustment”
earlier in this section.
SSS1173
Driver’s seatback release (CrossCabrio-
let models)
GUID-116F27BD-8437-47A9-8270-AD99D91FA75DTo exit the rear seat from the driver’s side, pull
the strap behind the driver’s seat to release the
driver’s seatback. The driver’s seatback will tilt
forward so that you can exit the vehicle.
NOTE:
Pulling the strap behind the driver’s seat
does not slide the driver’s seat forward.
You cannot slide the driver’s seat manu-
ally.
WARNING
Before using the driver’s seatback re-
lease, be sure that the driver’s seat is
not occupied by a driver and/or any
objects to avoid possible injuries and/
or damage.
Condition:

Black plate (33,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS0227A
RecliningGUID-1BFE5C97-1FC3-4054-A6B3-17A9466D0C05Pull the reclining strap*Aand position the
seatback at the desired angle. Release the
reclining strap after positioning the seat at the
desired angle.
The reclining feature allows adjustment of the
seatback for occupants of different sizes to help
obtain proper seat belt fit. (See “Precautions on
seat belt usage” later in this section.) The
seatback may also be reclined to allow occu-
pants to rest when the vehicle is parked.
WARNING
. Do not ride in a moving vehicle
when the seatback is reclined. This
can be dangerous. The shoulder belt
will not be against your body. In an
accident, you could be thrown into it
and receive neck or other serious
injuries. You could also slide under
the lap belt and receive serious
internal injuries.
. For the most effective protection
when the vehicle is in motion, the
seat should be upright. Always sit
well back in the seat with both feet
on the floor and adjust the seat belt
properly. See “Precautions on seat
belt usage” later in this section.
. After adjustment, check to be sure
the seat is securely locked.
HEAD RESTRAINTSGUID-5E605952-D804-4293-B401-616CD7C38955
WARNING
Head restraints supplement the other
vehicle safety systems. They may pro-
vide additional protection against injury
in certain rear end collisions. Adjust the
head restraints properly, as specified in
this section. Check the adjustment after
someone else uses the seat. Do not
attach anything to the head restraint
stalks or remove the head restraint. Do
not use the seat if the head restraint
has been removed. If the head restraint
was removed, install and properly ad-
just the head restraint before an occu-
pant uses the seating position. Failure
to follow these instructions can reduce
the effectiveness of the head restraints.
This may increase the risk of serious
injury or death in a collision.
Safety — Seats, seat belts and supplemental restraint system1-11
Condition:

Black plate (34,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-12Safety — Seats, seat belts and supplemental restraint system
JVR0140X
The illustration shows the seating positions
equipped with head restraints and headrest.
For Hardtop models, the head restraints and the
headrest are adjustable.
For CrossCabriolet models, the front head
restraints are adjustable and the rear head
restraints are not removable or adjustable.
Indicates the seating position is equipped
with a head restraint.
Indicates the seating position is equipped
with an adjustable headrest (for Hardtop mod-
els) .
SSS0992
ComponentsGUID-D58E33DF-16BC-41B1-B4C5-AA96E133EBC71. Head restraint
2. Adjustment notches
3. Lock knob
4. Stalks
SSS0997
AdjustmentGUID-ACB994E3-70CF-4004-BDD8-BB431714EC1EAdjust the head restraint so the center is level
with the center of your ears.
Condition: