2013 MITSUBISHI OUTLANDER XL ECU

2-34 Seat and restraint systems
2
2. Push down on the entire seat until it locks into place with
a click.NOTE
You can load luggage with the seatback folded down.3. While pulling on the lock release strap on the back of the
seatback, raise up the seatback.
4. After returning the seatback to its normal position, gently
shake the seat and seatback to make sure they are firmly
secured.
BK0150600US.book 34 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-35
2
5. Raise all the head restraints to the highest position.
Refer to “Head restraints: Adjustment of the head restraint
height” on page 2-26.
Making a flat seat
N00404800156
The entire interior of the vehicle may be used for sleeping
accommodations by removing the head restraints and fully
reclining all the seats when the vehicle is stopped.
WA R N I N G
!
After returning the seat to its normal position, raise
all the head restraints to the highest position. Using
the second row seat with the head restraints
retracted could cause a serious head injury or death
in the event of a collision or sudden breaking.
WA R N I N G
!
Never drive with passengers or cargo on the flat
seat. This is extremely dangerous and can cause
severe or fatal injury or death in an accident or if
heavy braking is required.
CAUTION
!
Adjust the seats only when the vehicle is stopped in a
safe place.
Seat should be adjusted only by adults to avoid acci-
dents.
When sliding the seats, be careful not to catch your
hand or leg.
Do not walk around on top of the seats after they
have been laid flat because the footing is uneven. It
is safest to move about on your hands and knees.
To ensure the seats are locked securely, attempt to
move them back and forth.
Do not jump on or drop heavy objects on the seat-
backs.
BK0150600US.book 35 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-42 Seat and restraint systems
2
3. Pull the seat belt out slowly while holding the latch plate.
Push the latch plate into the buckle until you hear a
“click”. Pull up on the belt to be sure the latch plate is
locked securely in the buckle.NOTE
If the seat belt locks up and cannot be pulled out, pull it
once with force and let it retract all the way.
Then, pull the belt out slowly once again.4. The lap part of the belt must always be worn low and snug
across the hips. Pull up on the shoulder portion of the belt
to take up any slack in the lap belt.
BK0150600US.book 42 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-44 Seat and restraint systems
2
If you then repeatedly stop and start your vehicle with the seat
belt unfastened, the warning light/display and tone will remind
you to fasten your seat belt every time the vehicle starts mov-
ing. You will also be reminded to fasten your seat belt in this
way when you remove your seat belt while driving. The warn-
ing light and the tone go off when the seat belt is fastened.NOTE
At the same time, “FASTEN SEAT BELT” will be dis-
played on the information screen in the multi-information
display.
Front passenger seat belt warning light
N00418300208
The front passenger seat belt warning light is located in the
instrument panel.
When the ignition switch is turned to the “ON” position, this
indicator normally comes on and goes off a few seconds later.
The light comes on when a person sits on the front passenger
seat but does not fasten the seat belt. It goes off when the seat
belt is subsequently fastened.
WA R N I N G
!
In order to reduce the risk of serious injury or death
in an accident, always fasten your own seat belt. Do
not allow anyone to ride in your vehicle unless he or
she is also seated and fastening a seat belt. Children
should additionally be restrained in a secure child
restraint system.
WA R N I N G
!
Do not install any accessory or sticker that makes
the light difficult to see.
BK0150600US.book 44 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-45
2
Adjustable seat belt shoulder anchor (front seats)
N00406300298
To move the anchor (A) down, press the lock knob (B) and
slide the anchor down to the desired position.Anchor down Anchor up
WA R N I N G
!
Always adjust the shoulder belt anchor so that the
shoulder belt is positioned across the center of your
shoulder without touching your neck. The shoulder
belt should not be able to fall off your shoulder. Fail-
ure to follow this instruction can adversely affect
seat belt performance and increase the risk of seri-
ous injury or death in the event of an accident.
Adjust the shoulder belt anchor only when the vehi-
cle is not in motion.
Make sure the anchor is securely locked in position
after adjusting it.
BK0150600US.book 45 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-53
2
NOTE
Before purchasing a child restraint system, try installing it
in the rear seat to make sure there is a good fit. Because of
the location of the seat belt buckles and the shape of the
seat cushion, it may be difficult to securely install some
manufacturer’s child restraint systems.
If the child restraint system can be pulled forward or to
either side easily on the seat cushion after the seat belt has
been tightened, choose another manufacturer’s child
restraint system.
Depending on the seating position in the vehicle and the
child restraint system that you have, the child restraint
system can be attached using one of the following 2 meth-
ods:
• Attach to the lower anchorage in the second row seat
ONLY if the child restraint system is compatible with
the LATCH system (See page 2-54).
• Attach to the seat belt (See page 2-57).
WA R N I N G
!
It is important to use an approved rear-facing infant
restraint until the infant is one year old (unless the
infant outgrows the seat sooner). This allows the
infant’s neck and spine to develop enough to support
the weight of their head in the event of an accident.
When installing a child restraint system, follow the
instructions provided by the manufacturer and fol-
low the directions in this manual. Failure to do so
can result in serious injury or death to your child in
an accident or sudden stop.
After installation, push and pull the child restraint
system back and forth, and side to side, to see that it
is firmly secured. If the child restraint system is not
installed securely, it may cause injury to the child or
other occupants in the event of an accident or sud-
den stop.
When not in use, keep your child restraint system
secured with the seat belt, or remove it from the
vehicle, in order to prevent it from being thrown
around inside the vehicle during an accident.
BK0150600US.book 53 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-54 Seat and restraint systems
2
Installing a child restraint system using the
LATCH (Lower Anchors and Tethers for chil-
dren) system
N00418800085
Lower anchor locationsThe outboard seating positions in the second row seat of your
vehicle are equipped with lower anchors for attaching child
restraint systems compatible with the LATCH system.NOTE
The symbols on the seatback show the location of the
lower anchor points.
Tether anchor locations
N00418900099
Your vehicle has 3 attachment points on the backside of the
second row seats. These are for securing a child restraint sys-
tem tether strap to each of the 3 rear seating positions in your
vehicle.
BK0150600US.book 54 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-55
2
Examples of child restraint systems compatible with the
LATCH system
N00419000198
Using the LATCH system
N00419100173
1. In order to securely fasten the tether strap, remove the
head restraint from the location where you wish to install
the child restraint system.
A- Rear-facing child restraint system
B- Front-facing child restraint system
C- Child restraint system lower anchor connectors
D- Tether strap
(These are only examples.)
BK0150600US.book 55 ページ ２０１２年３月３０日　金曜日　午前１０時４３分