2013 MITSUBISHI OUTLANDER SPORT language

3-124 Features and controls
3
NOTE
Mirror image is displayed on the screen.

Monitor brightness is adjusted automatically by sensors.

It is possible to change the display language of the screen.
For details, please refer to the separated owner’s manual
for “Mitsubishi Multi-Communication System” or
“Change language or turn off the inside rearview mirror
screen: To change the language of warning text (3)” on
page 3-124.

Under certain circumstances, it may become difficult to
see an image on the screen, even when the system is func-
tioning correctly.
• In a dark area, such as at night.
• When water drops or condensation are on the lens.
• When sun light or headlights shine directly into the lens. Change language or turn off the inside rearview
mirror screen
N00568900053
It is possible to turn off the screen of the inside rearview mirror
and change the language of the warning messages on the
screen.
To temporarily set the non-display modeIf you press the switch (1) while the image appears on the
screen, it goes off temporarily.
To return to display mode, press the switch again or perform
the following operation.
[Except for vehicles equipped with the Free-hand Advanced
Security Transmitter (F.A.S.T.-key)]
Turn the ignition switch to the “ON” position after turning to
“OFF” or “ACC” position.
[For vehicles equipped with the Free-hand Advanced Security
Transmitter (F.A.S.T.-key)]
Put the operation mode in ON after putting the operation mode
in OFF.
BK0150700US.book 124 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Features and controls3-125
3
To permanently set the non-display mode1. Turn the ignition switch to the “ON” position or put theoperation mode in ON.
2. Put the gearshift lever or the selector lever in the “R” posi- tion.
3. Press and hold down the switch (1) (for about 15 sec- onds).
While you keep the switch pressed, the orange indicator
(2) comes on. When the image goes off, the non-display
mode setting is completed.
To change the language of warning text (3)1. Turn the ignition switch to the “ON” position or put theoperation mode in ON.
2. Put the gearshift lever or the selector lever in the “R” posi- tion.
3. Press and hold down the switch (1) to enter language selection mode (for 6 to 11 seconds).
In this mode, the image appears and the green indicator
(2) comes on.
4. Press the switch until the desired language appears on the display.
Each time you press the switch, the language will change
to the next one. When the warning text flashes, setting is
completed.
CAUTION
!
For safety reasons, do not perform the following
operations with the engine running.
CAUTION
!
For safety reasons, do not perform the following
operations with the engine running.
BK0150700US.book 125 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Features and controls3-129
3
Multi-information display
N00555000265
The multi-information display displays warnings, the odometer, trip odometer, service reminder, engine coolant temperature, fue
l
remaining, outside temperature, selector lever position, all-wheel drive operation status, average and momentary fuel consumpti on,
driving range, average speed, instrument brightness, etc.
It is also possible to change elements such as the language and units used on the multi-information display.
With ignition switch or
operation mode is in OFF With ignition switch or operation
mode is in ON (CVT)
Type 1 Type 2 With ignition switch or operation
mode is in ON (Manual transaxle)
Type 1 Type 2 Type 1 Type 2
1- Warning display screen (With ignition switch or opera-
tion mode in OFF) → P.3-131
2- Information screen (With ignition switch or operation mode in OFF) → P.3-131
Interrupt display screen (With ignition switch or operation
mode in OFF) → P.3-134
3- Door ajar warning display screen (With ignition switch or operation mode in OFF) → P.3-135
4- Drive mode indicator display screen (if so equipped)
→ P.3-137
5- Warning display screen (With ignition switch or opera-
tion mode in ON) → P.3-137
6- Active stability control (ASC) OFF display screen (if so equipped) → P.3-137
7- Information screen (With ignition switch or operation mode in ON) → P.3-138
Interrupt display screen (With ignition switch or operation
mode in ON) → P.3-142
8- Selector lever position display screen (if so equipped) → P.3-143
9- Outside temperature display screen → P.3-143
BK0150700US.book 129 ページ ２０１２年３月２２日　木曜日　午後６時４６分

3-130 Features and controls
3
NOTE
The fuel units, temperature units, display language, and
other settings can be changed.
Refer to “Changing the function settings (With ignition
switch or operation mode in ON)” on page 3-148.

The display screen is different depending on whether the
ignition switch or the operation mode in OFF or ON.
Refer to “Information screen (With ignition switch or
operation mode in OFF)” on page 3-131.
Refer to “Warning display list (With ignition switch or
operation mode in OFF)” on page 3-164.
Refer to “Information screen (With ignition switch turned
from the “OFF” position to the “ON” position or opera-
tion mode changed from OFF to ON)” on page 3-136.
Refer to “Information screen (With ignition switch or
operation mode in ON)” on page 3-138.
Refer to “Warning display list (With ignition switch or
operation mode in ON)” on page 3-167.
10- Fuel remaining display screen → P.3-144
11- Engine coolant temperature display (if so equipped)
→ P.3-138
12- ECO mode indicator (if so equipped) → P.3-144
13- Gearshift indicator display screen (if so equipped)
→ P.3-71BK0150700US.book 130 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Features and controls3-131
3
Multi-information meter switch
N00555100149
The multi-information meter switch is a button marked
“INFO” on the left side of the dash.
Each time the multi-information meter switch is operated, a
sound is emitted and the multi-information display changes
between information such as warnings, Odometer (Type1), trip
odometer, service reminder, engine coolant temperature (Type
1), average and momentary fuel consumption, driving range,
and average speed.
It is also possible to change elements such as the language and
units used on the multi-information display by operating the
multi-information meter switch.
Warning display screen (With ignition switch
or operation mode in OFF)
N00555200179
If you press the multi-information meter switch and return
from the warning display screen to the previous screen, the
warning is displayed.
Refer to “Returning to the display screen from before the warn-
ing display” on page 3-134.
This mark is also displayed if there is another warning other
than the one displayed. When the cause of the warning display
is eliminated, the warning goes out automatically.NOTE
When the warning is displayed, the warning display
screen can be redisplayed on the information screen.
Refer to “Information screen (With ignition switch or
operation mode in OFF)” on page 3-131.
Refer to “Information screen (With ignition switch or
operation mode in ON)” on page 3-138.Information screen (With ignition switch or oper-
ation mode in OFF)
N00555300167
Each time you lightly press the multi-information meter
switch, the display screen switches in the following order.
BK0150700US.book 131 ページ ２０１２年３月２２日　木曜日　午後６時４６分

3-142 Features and controls
3

Average fuel consumption may vary depend on the driv-
ing conditions (road conditions, how you drive, etc.) The
actual fuel consumption may differ from the fuel con-
sumption displayed, so treat the fuel consumption dis-
played as just a rough guideline.

Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.

The display setting can be changed to the preferred units
{mpg(US), mpg(UK), L/100km or km/L}.
Refer to “Changing the function settings (With ignition
switch or operation mode in ON)” on page 3-148.Momentary fuel consumption displayWhile driving, the momentary fuel consumption is shown with
a bar graph.
When the momentary fuel consumption surpasses the average
fuel consumption, the momentary fuel consumption is dis-
played with a green bar graph. (Type 2)
Be conscious of maintaining the momentary fuel consumption
above the average fuel consumption, it can help you drive with
the better fuel consumption.NOTE
When the momentary fuel consumption cannot be mea-
sured, a bar graph is not shown.

The display setting can be changed to the preferred units
{mpg(US), mpg(UK), L/100km or km/L}.
Refer to “Changing the function settings (With ignition
switch or operation mode in ON)” on page 3-148.

It is possible to cancel the green bar graph.
Refer to “Changing the function settings (With ignition
switch or operation mode in ON)” on page 3-148.
Function setting screenThe “Display language”, “Temperature unit”, “Fuel consump-
tion unit”, and “Average fuel consumption and speed reset
method” settings can be modified as desired.
For further details, refer to “Changing the function settings
(With ignition switch or operation mode in ON)” on page 3-
148.Interrupt display screen (With ignition switch or
operation mode in ON)
N00556300180
Warning displayWhen there is information to be announced, such as a system
fault, a tone sounds and the information screen is switched to
the warning display screen.
Refer to the warning list and take the necessary measures.
Refer to “Warning display list (With ignition switch or opera-
tion mode in ON)” on page 3-167.
When the cause of the warning display is eliminated, the warn-
ing display goes out automatically.
Returning to the display screen from before the warning
display
Even if the cause of the warning display is not eliminated, you
can return to the screen that was displayed before the warning
display.
If you press the multi-information meter switch, the display
screen switches to the screen display from before the warning
and the warning (A) is displayed.
BK0150700US.book 142 ページ ２０１２年３月２２日　木曜日　午後６時４６分

Features and controls3-149
3
3. Press and hold the multi-information meter switch (forabout 2 seconds or more) to switch from the setting mode
screen to the menu screen.
NOTE
To return the menu screen to the function setting screen,
press and hold the multi-information meter switch (for
about 2 seconds or more).

If no operations are made within about 15 seconds of the
menu screen being displayed, the display returns to the
function setting screen.
4. Select the item to change on the menu screen and change to the desired setting. For further details on the operation
methods, refer to the following sections.
Refer to “Changing the reset mode for average fuel con-
sumption and average speed” on page 3-150.
Refer to “Changing the fuel consumption display unit” on
page 3-151.
Refer to “Changing the temperature unit” on page 3-153.
Refer to “Changing the display language” on page 3-154.
Refer to “Changing the language on Mitsubishi Multi-
Communication System or Bluetooth
® 2.0 interface to
match the multi-information display (if so equipped)” on
page 3-155.
Refer to “Operation sound setting” on page 3-156.
Refer to “Changing the time until “REST REMINDER” is
displayed” on page 3-157.
Refer to “Changing the turn signal sound” on page 3-158.
Refer to “Changing the momentary fuel consumption dis-
play (Type 2)” on page 3-159.
Refer to “Returning to the factory settings” on page 3-
160.
CAUTION
!
For safety, stop the vehicle before operating.
While driving, even if you operate the multi-infor-
mation meter switch, the function setting screen is
not displayed.Type 1
Type 2
BK0150700US.book 149 ページ ２０１２年３月２２日　木曜日　午後６時４６分

3-154 Features and controls
3
3. Press and hold the multi-information meter switch (forabout 2 seconds or more) to change in sequence from °F
→ ° C → ° F.
The setting is changed to the selected temperature unit.NOTE
If the battery is disconnected, the memory of the unit set-
ting is erased and is automatically set to °F (° C).
Changing the display language
N00557300161
The language of the multi-information display can be changed.
1. Press and hold the multi-information meter switch (for about 2 seconds or more) to change from the setting mode
screen to the menu screen.
Refer to “Changing the function settings (With ignition
switch or operation mode is in ON)” on page 3-148.
2. Lightly press the multi-information meter switch to select “LANGUAGE” (language setting).Type 1
Type 2
BK0150700US.book 154 ページ ２０１２年３月２２日　木曜日　午後６時４６分