Page 664 of 706
Vehicle care and maintenance
7-83
7
Back-up lights
N00901200066
1. Insert a screwdriver into the notch of the cover and pry
gently to remove the cover.NOTEWrap a cloth around the tip of the screwdriver to keep
from scratching the cover.2. Remove the socket and bulb assembly by turning it coun-
terclockwise.
BK0151000US.book 83 ページ ２０１２年３月２９日 木曜日 午後６時８分
Page 666 of 706
Vehicle care and maintenance
7-85
7
License plate lights
N00944000357
1. When removing the light unit (A), push it toward the left
side of the vehicle body.2. Use a screwdriver to gently pry up the tab (B) and remove
the lens.
NOTEWrap a piece of cloth around the tip of the screwdriver to
keep from scratching the lens.
BK0151000US.book 85 ページ ２０１２年３月２９日 木曜日 午後６時８分
Page 667 of 706
7-86 Vehicle care and maintenance
7
3. Pull the bulb out of the socket. 4. To install the bulb, perform the removal steps in reverse.
NOTEWhen installing the light, insert tab (C) first then align and
insert tab (D).
BK0151000US.book 86 ページ ２０１２年３月２９日 木曜日 午後６時８分
Page 668 of 706
Vehicle care and maintenance
7-87
7
Dome light (front)/Reading lights
N00944500235
1. Insert a screwdriver into the notch of the light assembly.
Gently pry to remove the lens.NOTEWrap a cloth around the tip of the screwdriver to keep
from scratching the lens.2. While holding down the tab (A), pull out the bulb.
3. To install the bulb, perform the removal steps in reverse.
BK0151000US.book 87 ページ ２０１２年３月２９日 木曜日 午後６時８分
Page 669 of 706
7-88 Vehicle care and maintenance
7
NOTEBefore replacing the bulb, put the dome light (front)/read-
ing lights switch into the “OFF” position.
When mounting the lens, align the tab (B) with the hole
on the vehicle body.
Dome light (rear)
(if so equipped)
N00944100329
1. Insert a screwdriver into the notch of the light assembly
and pry gently to remove the lens.NOTEWrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
BK0151000US.book 88 ページ ２０１２年３月２９日 木曜日 午後６時８分
Page 670 of 706
Vehicle care and maintenance
7-89
7
2. While holding down the tab (A), pull out the bulb.
3. To install the bulb, perform the removal steps in reverse.
NOTEBefore replacing the bulb, put the dome light (rear) switch
into the “OFF” position.
When mounting the lens, align the tabs (B) with the holes
on the vehicle body.
BK0151000US.book 89 ページ ２０１２年３月２９日 木曜日 午後６時８分
Page 671 of 706
7-90 Vehicle care and maintenance
7
Cargo room light
N00950000075
1. Insert a screwdriver into the notch of the light assembly
and pry gently to remove the lens.NOTEWrap a cloth around the tip of the screwdriver to keep
from scratching the lens.2. Remove the bulb by pulling it out.
3. To install the bulb, perform the removal steps in reverse.
NOTEBefore replacing the bulb, put the cargo room light switch
into the “OFF” position.
BK0151000US.book 90 ページ ２０１２年３月２９日 木曜日 午後６時８分
Page 673 of 706
7-92 Vehicle care and maintenance
7Cleaning the inside of your vehicle
N00945200109
After washing the inside of your vehicle with any cleaner, wipe
it dry in a shady, well ventilated area. NOTEAlways read the instructions on the cleaner label.Plastic, vinyl leather, fabric and flocked parts
N00945300168
1. Lightly wipe these off with a soft cloth soaked in a 3 %
solution of gentle soap and water.
2. Dip cloth in fresh water and wring out well. Using this
cloth, wipe off the detergent thoroughly.
NOTEDo not use cleaners, conditioners, and protectants contain-
ing silicones or wax.
Such products, when applied to the instrument panels or
other parts, may cause reflections on the windshield and
obscure vision.
Also, if such products get on the switches of the electrical
accessories, it may lead to failure of these accessories.Upholstery
N00945500131
1. To maintain the value of your new vehicle, maintain the
upholstery carefully and keep the interior clean.
Use a vacuum cleaner and brush to clean the seats. If
stained, vinyl and synthetic leather should be cleaned with
an appropriate cleaner. Cloth fabrics can be cleaned with
either upholstery cleaner or a 3 % solution of gentle soap
in lukewarm water.
2. Clean the carpeting with a vacuum cleaner and remove
any stains with carpet cleaner. Oil and grease can be
removed by lightly dabbing with a clean white cloth and
spot remover. NOTEIf fuzzing is difficult to remove from the seat upholstery,
draw a suitable defuzzing brush over the surface in one
direction.
CAUTION
!Do not use organic substances (solvents, benzine,
kerosene, alcohol, gasoline, etc.) or alkaline or acidic
solutions.
These chemicals can cause discoloring, staining or
cracking of the surface.
If you use cleaners or polishing agents, make sure
their ingredients do not include the substances men-
tioned above.
BK0151000US.book 92 ページ ２０１２年３月２９日 木曜日 午後６時８分
