2013 MITSUBISHI LANCER bulb

7-68 Vehicle care and maintenance
7
3. Turn the socket (D) counterclockwise to remove it.
4. Pull the bulb out of the socket.5. To install the bulb, perform the removal steps in reverse.
BK0150800US.book 68 ページ ２０１２年３月２９日　木曜日　午後２時３８分

7-70 Vehicle care and maintenance
7
2. Remove the entire socket and bulb assembly (E) by turn-
ing it counterclockwise.3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.*- Front of the vehicle
BK0150800US.book 70 ページ ２０１２年３月２９日　木曜日　午後２時３８分

Vehicle care and maintenance
7-73
7
4. Remove the bulb assembly (E) by turning it counterclock-
wise.
5. To install the bulb, perform the removal steps in reverse.
NOTE
When mounting the cover, align the hooks (F) on the
cover with the hole in the body.
BK0150800US.book 73 ページ ２０１２年３月２９日　木曜日　午後２時３８分

7-74 Vehicle care and maintenance
7
Front fog lights (Type 2)
(if so equipped)
N00943600747
1. Remove the screw (A).
CAUTION
!
Handle halogen light bulbs with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen lights bulb with a bare hand,
dirty glove, etc.
The oil from your hand could cause the bulb to
break the next time the fog lights are used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0150800US.book 74 ページ ２０１２年３月２９日　木曜日　午後２時３８分

Vehicle care and maintenance
7-77
7
5. Remove the bulb assembly (E) by turning it counterclock-
wise.
6. To install the bulb, perform the removal steps in reverse.
NOTE
When mounting the cover, align the hook (F) on the cover
with the hole in the body.
BK0150800US.book 77 ページ ２０１２年３月２９日　木曜日　午後２時３８分

7-78 Vehicle care and maintenance
7
Rear combination lights
N00943700386
Tail and stop lights, rear turn signal lights and rear
side-marker lights1. Remove the screws (A) from the light unit.
CAUTION
!
Handle halogen light bulbs with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen lights bulb with a bare hand,
dirty glove, etc.
The oil from your hand could cause the bulb to
break the next time the fog lights are used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0150800US.book 78 ページ ２０１２年３月２９日　木曜日　午後２時３８分

Vehicle care and maintenance
7-79
7
2. Remove the light unit in the rear direction. 3. Remove the socket and bulb assemblies by turning them
counterclockwise.
B- Tail and stop light
C- Rear turn signal light
D- Rear side-marker light
BK0150800US.book 79 ページ ２０１２年３月２９日　木曜日　午後２時３８分

7-80 Vehicle care and maintenance
7
4. Remove the bulb by pulling it out. 5. To install the bulb, perform the removal steps in reverse.
NOTE
When mounting the light unit, align the pins (E) on the
light unit with the holes in the body.
Tail and stop light and
Rear turn signal lightRear side-marker lightBK0150800US.book 80 ページ ２０１２年３月２９日　木曜日　午後２時３８分