2013 MAZDA MODEL CX-9 low beam

Black plate (226,1)
Signal Warning/Indicator Lights Page
Low Fuel Warning Light 5-55
Check Fuel Cap Warning Light 5-55
Seat Belt Warning Light 5-55
Door-Ajar Warning Light 5-55
Low Washer Fluid Level Warning Light 5-55
Automatic Transaxle Warning Light 5-55
AWD Warning Light 5-56
Tire Pressure Monitoring System Warning Light 5-56
KEY Warning Light (Red)/KEY Indicator Light (Green) 5-58
Security Indicator Light 5-60
Headlight High-Beam Indicator Light 5-60
Shift Position Indicator Light 5-60
TCS/DSC/RSC Indicator Light 5-61
TCS OFF Indicator Light 5-61
Cruise Main Indicator Light (Amber)/Cruise Set Indicator Light (Green) 5-61
BSM OFF Indicator Light 5-62
5-50
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
CX-9_8CM9-EA-12I_Edition1 Page226
Thursday, September 13 2012 2:36 PM
Form No.8CM9-EA-12I

Black plate (236,1)
NOTE
The advanced key can be set so that the KEY
indicator light (green) does not flash even if
the battery power is low.
Refer to Personalization Features on page
10-8.
qSecurity Indicator Light
This indicator light starts flashing every 2
seconds when the ignition is switched
from ON to ACC and the immobilizer
system is armed.
The light stops flashing when the ignition
is switched ON with the correct ignition
key.
At this time, the immobilizer system is
disarmed and the light illuminates for
about 3 seconds and then turns off.
If the engine does not start with the
correct ignition key, and the security
indicator light keeps illuminating or
flashing, the system may have a
malfunction. Consult an Authorized
Mazda Dealer.
qHeadlight High-Beam Indicator
Light
This light indicates one of two things:lThe high-beam headlights are on.lThe turn signal lever is in the flash-to-
pass position.
qShift Position Indicator Light
This indicates the selected shift position
when the ignition is switched ON.
Gear position indicator
5-60
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
CX-9_8CM9-EA-12I_Edition1 Page236
Thursday, September 13 2012 2:36 PM
Form No.8CM9-EA-12I

Black plate (244,1)
NOTElThe headlights, other exterior lights and dashboard illumination may not turn off immediately
even if the surrounding area becomes well-lit because the light sensor determines that it is
nighttime if the surrounding area is continuously dark for several minutes such as inside long
tunnels, traffic jams inside tunnels, or in indoor parking lots.
In this case, the light turns off if the light switch is turned to the OFF position.
lThe dashboard illumination can be adjusted by rotating the knob in the instrument cluster. Also,
the day/night mode can be changed by pressing the knob. To adjust the brightness of the
dashboard illumination: Refer to Dashboard Illumination on page 5-48.
lThe sensitivity of the AUTO lights may be changed by an Authorized Mazda Dealer. Refer to
Personalization Features on page 10-8.
Xenon fusion headlight bulbsí
The low-beam bulbs of the headlights have xenon fusion bulbs that produce a bright white
beam over a wide area.
WARNING
Do not replace the xenon fusion bulbs yourself
Replacing the xenon fusion bulbs yourself is dangerous. Because the xenon fusion
bulbs require high voltage, you could receive an electric shock if the bulbs are
handled incorrectly. Consult an Authorized Mazda Dealer when the replacement is
necessary.
NOTE
If the headlights flicker, or the brightness weakens, the bulb-life may be depleted and a replacement is
necessary. Consult an Authorized Mazda Dealer.
qLights-On Reminderí
If lights are on and the ignition is
switched to ACC or the ignition is
switched off, or the key is removed from
the ignition switch/key slot, a continuous
beep sound will be heard when the
driver's door is opened.
NOTE
l(With advanced key)
When the advanced keyless function is used
and the ignition is switched to ACC, the
“Ignition Not Switched Off (STOP)
Warning Beep”(page 3-18) overrides the
lights-on reminder.
lWhen the ignition is switched to ACC or the
ignition is switched off, the“Ignition Key
Reminder”(page 5-3) overrides the lights-
on reminder.
qHeadlight High-Low Beam
Press the lever forward to turn on the high
beams.
Pull the lever back to its original position
for the low beams.
5-68
Driving Your Mazda
íSome models.
Switches and Controls
CX-9_8CM9-EA-12I_Edition1 Page244
Thursday, September 13 2012 2:36 PM
Form No.8CM9-EA-12I

Black plate (245,1)
Type A
High beam
Low beam
Type B
High beam
Low beam
qFlashing the Headlights
To flash the headlights, pull the lever fully
towards you (the headlight switch does
not need to be on). The lever will return to
the normal position when released.
Type A
OFF
Flashing
Type B
OFF
Flashing
Driving Your Mazda
Switches and Controls
5-69
CX-9_8CM9-EA-12I_Edition1 Page245
Thursday, September 13 2012 2:36 PM
Form No.8CM9-EA-12I

Black plate (419,1)
qDisplayable Range on the Screen
The images on the screen may be different from the actual conditions.
(Screen display)
(Actual view)
ObjectGarnish
Bumper
NOTElThe displayable range varies depending on the vehicle and road conditions.lThe displayable range is limited. Objects under the bumper or around the bumper ends cannot be
displayed.
lThe distance appearing in the displayed image is different from the actual distance because the
rear view parking camera is equipped with a specific lens.
lSome optionally installed vehicle accessories may be picked up by the camera. Do not install any
optional parts that can interfere with the camera view, such as illuminating parts or parts made of
reflective material.
lIt may be difficult to see the display under the following conditions, however, it does not indicate a
malfunction.
lIn darkened areas.lWhen the temperature around the lens is high/low.lWhen the camera is wet such as on a rainy day or during periods of high humidity.lWhen foreign material such as mud is stuck around the camera.lWhen the camera lens reflects sunlight or headlight beams.lImage display may be delayed if the temperature around the camera is low.
Interior Comfort
Rear View Monitor
6-155
CX-9_8CM9-EA-12I_Edition1 Page419
Thursday, September 13 2012 2:38 PM
Form No.8CM9-EA-12I

Black plate (508,1)
Light Bulbs
High-mount brake lightFog lights
Side turn
signal lights
Some models.
License plate lights
Brake lights/TaillightsTaillights (Liftgate side) Vanity mirror
lights Overhead light (Front)/Map lights
Overhead light (Center)
Overhead light (Rear)
Headlights
(Low beam) Front turn
signal lights Front side-
marker lights
Rear side marker lights
Rear turn signal lights Reverse lights
Luggage
compartment light
Headlights (High
beam)/Running lights Parking lights
Fog lights
Side turn
signal lights Vanity mirror
lights Overhead light (Front)/Map lights
Overhead light (Center)
Overhead light (Rear)
Headlights
(Low/High beam) Front turn
signal lights Front side-
marker lights
Parking lights/
Running lights
With xenon fusion headlights With halogen headlights
Courtesy lights
8-40
Maintenance and Care
Owner Maintenance
CX-9_8CM9-EA-12I_Edition1 Page508
Thursday, September 13 2012 2:40 PM
Form No.8CM9-EA-12I

Black plate (509,1)
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement
is necessary.
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
qReplacing Exterior Light Bulbs
Headlights (With xenon fusion
headlights)
Low/High beam bulbs
You cannot replace the low/high beam
bulbs by yourself. The bulbs must be
replaced at an Authorized Mazda Dealer.
Headlights (With halogen headlights)
High-beam bulbs
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.
3. Turn the cover counterclockwise and
remove it.
4. Disconnect the electrical connector
from the bulb by pulling the tab on the
connector with your finger and pulling
the connector downward.
Maintenance and Care
Owner Maintenance
8-41
CX-9_8CM9-EA-12I_Edition1 Page509
Thursday, September 13 2012 2:40 PM
Form No.8CM9-EA-12I

Black plate (510,1)
5. Turn the socket and bulb assembly to
remove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
6. Install the new bulb in the reverse order
of the removal procedure.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Low-beam bulbs
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.3.(Right side)
Remove the attachment bolts and the
coolant reservoir before replacing the
light bulb.
4. Turn the cover counterclockwise and
remove it.
8-42
Maintenance and Care
Owner Maintenance
CX-9_8CM9-EA-12I_Edition1 Page510
Thursday, September 13 2012 2:40 PM
Form No.8CM9-EA-12I