Page 3 of 16
Request switch
Request switch Exterior aerial
Operational range80cm (31in) 80cm (31in)
Lock release
lever
Before Driving
Operational Range
The advanced keyless system operates only when the driver is in the vehicle or
within operational range while the key is being carried.
All doors and the liftgate can be locked/unlocked by pressing the request switch
on the front doors while the key is being carried.
The request switch on the liftgate can only be used to lock all doors and the
liftgate.
Locking, Unlocking with Request Switch
Steering Wheel Adjustment
1. Stop the vehicle, and then pull down the lock release
lever under the steering column.
3. Attempt to push the steering wheel up and down
to make sure it's locked before driving. 2. Tilt the steering wheel and/or adjust the steering
column length to the desired positions, and then
push the lever up to lock the column.
2
Front doors (Lock/Unlock) Liftgate (Lock only)
For details, refer to Section 3, “Advanced Keyless Entry and Start System”,
“Doors and Locks” or “Steering Wheel”.
% : A ' , ' ' & A ' F K V K Q P A 3 W K E M ) W K F G K P F D
Page 12 of 16
When Driving
11
Smart City Brake Support (SCBS)
The Smart City Brake Support (SCBS) system is designed to reduce damage in the
event of a collision by operating the brake control (SCBS brake) when the
system's laser sensor detects a vehicle ahead and determines that a collision with
the vehicle ahead is unavoidable.
For details, refer to Section 4, “Smart City Brake Support (SCBS)”.
It may also be possible to avoid a collision if the relative speed between your
vehicle and the vehicle ahead is less than about 15 km/h (9.3 mph).
Do not rely completely on the Smart City Brake Support (SCBS) system:
The Smart City Brake Support (SCBS) is a system which operates in response to a
vehicle ahead. It does not apply to 2-wheeled vehicles or pedestrians.
If the vehicle height or inclination is changed, the system will not be able to
correctly detect vehicles ahead resulting in the Smart City Brake Support
(SCBS) system not operating normally or mistakenly operating, which
could cause a serious accident.
WARNING
Do not modify the suspension:
NOTE
The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a
near-infrared laser beam and receiving the beam reflected off the reflector of the
vehicle ahead, and then using it for the measurement. Consequently, the Smart
City Brake Support (SCBS) may not operate under the following conditions:
• Trucks with low loading platforms and vehicles with an extremely low or
high profile.
• Under bad weather condition, such as rain, fog and snow.
• The window washer is being used or the windscreen wipers are not used when
its raining.
• The windscreen is dirty.
• The steering wheel is turned completely left or right, or the vehicle is acceler-
ated rapidly and comes close to the vehicle ahead.
Other details are described in the related text.
% : A ' , ' ' & A ' F K V K Q P A 3 W K E M ) W K F G K P F D
Page 13 of 16
When Driving
12
X Mark Full Low
For details, refer to Section 4, “Switches and Controls”, “ABS/TCS/DSC” or “Tyre Pressure
Monitoring System”.
Tyre Pressure Monitoring System
The Tyre Pressure Monitoring System (TPMS) monitors the air pressure of all
four tyres. If the air pressure of one or more tyres is too low, the system warns the
driver by indicating the tyre pressure monitoring system warning light in the
instrument cluster and operating a beep sound.
In the following cases, system initialization must be performed so that the system
operates normally.
• A tyre pressure is adjusted.
• Tyre rotation is performed.
• A tyre or wheel is replaced.
• The battery is replaced or completely drained.
• The tyre pressure monitoring system warning
light is illuminated.
Diesel Particulate Filter
The diesel particulate filter collects and removes most of the particulate matter
(PM) in the exhaust gas of a diesel engine.
Inspect the engine oil level periodically. When inspecting the engine oil, if the
engine oil level is close to or exceeds the “X” mark on the dipstick, replace the
engine oil.
Whenever the engine oil is replaced, the vehicles engine control unit needs to be
reset according to the instruction in Workshop Manual as soon as possible.
Otherwise the engine oil warning light may illuminate. Consult an expert repairer
to reset the engine control unit, we recommend an Authorised Mazda Repairer.
% : A ' , ' ' & A ' F K V K Q P A 3 W K E M ) W K F G K P F D